微机械热对流倾角仪温度补偿技术研究

介绍了微机械热对流倾角仪的工作原理和结构设计,利用有限元分析软件,计算了在不同倾斜状态下二维密闭腔中点热源引起的对流场和温度场,提出了环境温度对热对流倾角仪影响的模型。根据仿真结果,在电路中增加了加热丝恒定温度控制电路,建立了基于软件的环境温度补偿算法,实现了对温度影响的补偿。经测试,环境温度从-40℃变化到60℃时,倾角仪0°输入的温度稳定性为0.07°,10°输入的温度稳定性为0.02°。     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

Routing Correlated Data with Fusion Cost in Wireless Sensor Networks

In this paper, we propose a routing algorithm called minimum fusion Steiner tree (MFST) for energy efficient data gathering with aggregation (fusion) in wireless sensor networks. Different from existing schemes, MFST not only optimizes over the data transmission cost, but also incorporates the cost for data fusion, which can be significant for emerging sensor networks with vectorial data and/or security requirements. By employing a randomized algorithm that allows fusion points to be chosen according to the nodes' data amounts, MFST achieves an approximation ratio of 5/4log(k + 1), where k denotes the number of source nodes, to the optimal solution for extremely general system setups, provided that fusion cost and data aggregation are nondecreasing against the total input data. Consequently, in contrast to algorithms that only excel in full or nonaggregation scenarios without considering fusion cost, MFST can thrive in a wide range of applications     

Environmental factors and kinetics of microbial degradation of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) in an aqueous medium

Environmental factors such as oxygen, temperature, and microbial species may have significant effects on decomposition of biodegradable polymers. A representative biodegradable, thermoplastic polymer, poly(3‐hydroxybutyrate‐co‐hydroxyvalerate) (PHBV), was decomposed in an aqueous medium under controlled laboratory conditions by soil microbes for the intrinsic degradation kinetics and the effects of the environmental factors on polymer biodegradation. The amount of proteins, including the PHBV depolymerases, that attached to the polymer surfaces was quite constant during the period of significant mass loss of the polymer specimens. The microbial polymer degradation followed a zero‐order rate model, so the residual mass fraction of PHBV films declined linearly with time. The mixed aerobic microbial organisms from fertile soil showed a higher activity of polymer degradation than an aerobic PHBV‐producing bacterium and the mixed anaerobes in the same soil. The mixed anaerobic microorganisms from barren soil decomposed the polymer at a slower rate than the anaerobes from fertile soil, and this was attributed to fewer microbial cells in the barren soil instead of the difference in the microbial species. The temperature effect on PHBV degradation can be described with an Arrhenius equation, and the activation energy is around 16 kcal/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 205–213, 2003     

电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

随机激光器的最新进展

综述了近年来随机激光器的最新研究结果，包括随机激光产生的机制，随机增益介质的制备方法，随机激光器的激励与发光特性和随机激光理论。最后，介绍了随机激光器的应用前景。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。     

热管传热性能对小型热管换热器散热效能影响

在零重力辅助下,小热管热阻是小型热管换热器散热效能的重要影响因素之一。基于集总参数法对于换热器系统数值计算的高效性思想,建立了热管、热管换热器的集总参数模型。对同一热管换热器选用不同传热性能的热管,在不同传热温差和流体质量流速下,就其散热效能进行了数值计算。计算结果表明,在零重力辅助下,热管换热器管内热阻存在一临界值Rcri。当热阻RHP≤Rcri时,管外热阻起主导作用,热管换热器的散热效能εh几乎不随热管管内热阻的值而变化。     

关于我国钢铁工业发展战略的思考

21世纪初是世界经济发展的重大战略机遇期,如何抓住机遇加快发展,是中国钢铁行业应认真思考的问题。十一五我国钢铁工业的发展,靠什么来拉动,还能靠大规模的投资吗?目前我们还不能生产的双高产品怎么办,靠花钱能买来技术吗?靠市场能换来核心产品吗?值得深思。当今,我们思考的不仅应考虑个别企业的生存问题,而更应考虑的是钢铁行业整体的长远发展问题,即