基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

Interaction of triton X-100 on silica: A relationship between surface characteristics and adsorption isotherms

Adsorption of Triton X-100 on various silica substrates has been investigated. A number of solids, including a natural quartz, this quartz washed with HCl acid and subsequently heated at 1273 K; two aerosils and one Kieselgel silicas were studied. These solids exhibit surface areas in the range of 5 to 430 m² g^?1. All the Triton adsorption isotherms display an S-shape at the adsorption temperatures studied (298 and 308 K). It has been found that the pretreatments of natural quartz (by water washing, impurities removed by acid and/or high temperature calcination) affect considerably the amounts of TX-100 adsorbed. Measurements of surface composition have been made by X-ray photoelectron spectroscopy (XPS) with particular emphasis on the presence of impurities and on the number of OH groups at the surface of the samples. The nature of the surface hydroxyl has also been studied by infrared spectroscopy. Furthermore, the specific number of hydroxyl groups on the surface of the silica samples has been determined by thermogravimetric analysis. Finally an attempt to correlate solid surface characteristics with adsorption isotherms has been developed.     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Preparation and characterization of proton‐exchange hybrid membranes

Two types of composite were prepared, based on a thermoplastic polymer, polyvinylidene fluoride (PVDF), and an elastomer, ethylene‐propylene‐diene terpolymer (EPDM), respectively. We obtained both series by addition of an inorganic proton‐conducting antimonic acid derivative (HSb) and polystyrene crosslinked with a small percentage of divinylbenzene (PS‐co‐DVB). From these composites, membranes were obtained and subjected to a heterogeneous‐phase sulfonation reaction with chlorosulfonic acid. All experimental materials were characterized from a morphological and electrical point of view, by means of techniques such as differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), non‐isothermal crystallization and complex impedance analysis. Copyright © 2005 Society of Chemical Industry     

Specific interactions in blends containing Chitosan and functionalized polymers. Molecular dynamics simulations

Chitosan (CS)/poly(vinyl alcohol) (PVA) and Chitosan/poly(2-hydroxyethyl methacrylate) (P2HEM) blends have been studied through molecular dynamic simulations. In a previous work it was found miscibility between these polymers and it was attributed to hydrogen bonding formation. However, the experimental information obtained was not enough to know which of the interacting groups of Chitosan, i.e. -CH₂OH or -NH₂, are responsible of the interaction. Therefore, we have performed molecular dynamics simulation runs of 1 ns in order to calculate radial distribution functions (RDF) for the groups tentatively involved in the interaction. The results are correlated with our previous experimental data. This way, we have obtained a more precise conclusive information about the interactions involved as function of the blends composition. For low compositions of PVA and P2HEM the interaction is predominantly with the hydroxymethyl groups of CS while as the composition of PVA and P2HEM increases, the interaction with the amine groups increases.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Manual dexterity of older Mexican American adults: a cross-sectional pilot experimental investigation

This paper reports results from an experimental pilot study performed to quantify the manual dexterity of older Mexican American adults. The Purdue pegboard test, a two-arm coordination test, and a hand-tool dexterity test were used in this study. To enable cross-sectional comparisons of manual dexterity measures of older Mexican American adults with young Mexican American adults, these tests were administered to 18 older Mexican American adults aged 63–85 (mean age: 71.3 years, SD: 7.0 years), recruited from senior recreation centers in El Paso, and eighteen young adults aged 21–32 (mean age: 25.6 years, SD: 3.8 years) recruited from the student body at the University of Texas at El Paso. For the Purdue pegboard test, the number of pegs placed in 30 s using the preferred hand, the non-preferred hand, and both hands were first individually monitored. Then, scores on an assembly task using the Purdue pegboard were obtained. For the two-arm coordination test, participants were required to trace a star pattern with a stylus using both hands. The time for task completion and the number of errors made during task performance were monitored. For the hand-tool dexterity test, participants were required to use common hand tools and remove nuts and bolts from one side of a wooden upright, and to assemble nuts and bolts in the corresponding holes on the other side of the upright. The time taken for task completion was recorded. Since modified Levene's test showed equality of variances, two sample t-tests, comparing the mean responses of older adults with the mean responses of young adults for each individual test, were conducted. Results indicate that responses for the older adults were statistically significant different (p<0.001) from young adults for all Purdue pegboard tasks. On the average, older adults performed significantly slower (p<0.001) than young adults on the two-arm coordination test, and committed more errors before task completion (p<0.05). Older adults also took longer to complete the hand-tool dexterity task compared to their younger counterparts (p<0.05). In addition to the t-tests, manual dexterity performance measures from older adults were regressed with age to determine the cross-sectional age effects on manual dexterity measures. Results indicate that all Purdue pegboard performance measures were significantly affected by age (p<0.05). The time to complete the two-arm coordination test was significantly linearly related to age (p<0.05). However, the number of errors committed by older adults in the performance of the two-arm coordination test was not significantly linearly related to age. Time to complete the hand-tool dexterity was also significantly linearly related to age (p<0.05). Accommodating age-related changes in manual dexterity is important for job design in industry, especially in industries employing older adults requiring significant assembly and hand-tool use.

Relevance to industry

Given the aging of the industrial workforce, it is important to understand how manual dexterity is affected by age, so that jobs requiring significant manual dexterity for task initiation, task performance and task completion are designed to fit older adult dexterity levels.     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.     

Molecular weight effect on the obtainment of parallel and perpendicular orientation in thermotropic poly(diethylene glycol <Emphasis Type="Italic">p,p′</Emphasis>-bibenzoate)

Summary The effect of molecular weight on the uniaxial orientation process has been analyzed in two samples of thermotropic poly(diethylene glycol p,p′-bibenzoate), evaluating the influence of that parameter on the type of orientation obtained. Several strain rates and deformation temperatures have been tested in order to map out the conditions for obtaining the two different kinds of orientation. The results show that in the lower molecular weight PDEB sample (M_w=31200) it is rather easy to get exclusively perpendicular “anomalous” orientation, with the molecular axes aligned transversely to the stretching direction. However, it is extremely difficult to obtain 100% parallel “normal” orientation. On the contrary, either type of orientation or a mixture of them can be easily developed for the higher molecular weight PDEB sample (M_w=102900).