Molecular beam epitaxy growth of TmP/GaAs and transistor action inGaP/TmP/GaAs heterostructures

The growth of thulium phosphide (TmP) by molecular beam epitaxy (MBE) on GaAs substrate is reported. Good epilayer quality was demonstrated through X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM) analysis. The closely lattice matched TmP layer was n-type with an electron concentration of 1.6×10²¹ cm^-3 and a room temperature mobility of 4.8 cm²V^-1s^-1. The Schottky barrier height determined from 1/capacitance² (1/C²) versus voltage (V) measurements is about 0.81 eV which agrees well with the value obtained through the current-voltage (I-V) measurements. In this work, we also report transistor action in a GaP/TmP/GaAs structure, for which chemical bonding techniques were employed. From I-V measurements, a common base current gain α≈0.55 at V_CB=0 was obtained at room temperature     

Low-cost broadband millimetre-wave array antenna using waveguide/microstrip feed network and slot pair

A low-cost broadband millimetre-wave planar 30/spl times/30 array antenna is presented. The antenna is fed by a microstrip feed network in the H-plane to decrease fabrication costs, and a waveguide feed network in the E-plane to reduce the feed line loss. The waveguide and microstrip feed network are coupled through the proposed slot pair. The slots are placed one quarter of a guided-wavelength distance apart, so that the reflected waves from the slots cancel each other. A conductive bar is laid above the slots to increase the coupling, which increases the antenna gain by about 1 dBi. The maximum gain is 30.5 dBi at 41.5 GHz. The measured bandwidth is as broad as 7.1%.     

Enhanced carrier mobility and photon-harvesting property by introducing Au nano-particles in bulk heterojunction photovoltaic cells

In this study, polymer solar cells (PSCs) doped with Au nanoparticles (Au NPs) were successfully fabricated to maximize the photon-harvesting properties on the photoactive layer. In addition, a conductivity-enhanced hybrid buffer layer was introduced to improve the photon absorption properties and effectively separate the generated charges by adding Au NPs and dimethylsulfoxide (DMSO) to the PH 500 as a buffer layer. The PSC performance was optimized with a 88% improvement over the conventional PSCs (photoactive area: 225 mm², power conversion efficiency (PCE): 3.2%) by the introduction to the buffer layer of Au NPs and DMSO at 10 wt% and 1.0 wt%, respectively, and with 15 wt% Au NP doping in the photoactive layer. The internal resistance was decreased due to the increased photocurrent caused by the localized surface plasmon resonance (LSPR) effect of the Au NPs in the photoactive layer and by the improvement of carrier mobility induced by the DMSO doping of the buffer layer. As a result, the series resistance (R_S) deceased from 42.3 to 19.7 Ω cm² while the shunt resistance (R_SH) increased from 339 to 487 Ω cm².     

Design of Rate-Compatible Block Turbo Code with a Low-Degree Generating Polynomial

This paper presents a Rate-Compatible Block Turbo Code (RC-BTC) with increased transmission capacity. The proposed RC-BTC uses a new algorithm called information augmenting scheme, and can achieve a higher code rate than conventional one. A new Error Location Finding (ELF) Decoding Algorithm is introduced to solve the decoding problem of the information augmenting scheme. As a result, a novel error-correcting capability of the BTC-applied Chase-ELF Hybrid Decoder, combining the previous Chase–Pyndiah algorithm and the proposed ELF algorithm, is demonstrated via Monte-Carlo simulation. In addition, the proposed code maximally increases the transmission capacity with the Chase-ELF Hybrid decoder using an information augmenting scheme.     

Miniaturized Flexible Electronic Systems with Wireless Power and Near‐Field Communication Capabilities

A class of thin, lightweight, flexible, near‐field communication (NFC) devices with ultraminiaturized format is introduced, and systematic investigations of the mechanics, radio frequency characteristics, and materials aspects associated with their optimized construction are presented. These systems allow advantages in mechanical strength, placement versatility, and minimized interfacial stresses compared to other NFC technologies and wearable electronics. Detailed experimental studies and theoretical modeling of the mechanical and electromagnetic properties of these systems establish understanding of the key design considerations. These concepts can apply to many other types of wireless communication systems including biosensors and electronic implants.     

Sliding Mode Observer Driver IC Integrated Gate Driver for Sensorless Speed Control of Wide Power Range of PMSMs

This work proposes a highly efficient sensorless motor driver chip for various permanent‐magnet synchronous motors (PMSMs) in a wide power range. The motor driver chip is composed of two important parts. The digital part is a sensorless controller consisting mainly of an angle estimation block and a speed control block. The analog part consists of a gate driver,which is able to sense the phase current of a motor. The sensorless algorithms adapted in this paper include a sliding mode observer (SMO) method that has high robust characteristics regarding parameter variations of PMSMs. Fabricated SMO chips detect back electromotive force signals. Furthermore, motor current–sensing blocks are included with a 10‐bit successive approximation analog‐to‐digital converter and various gain current amplifiers for proper sensorless operations. Through a fabricated SMO chip, we were able to demonstrate rated powers of 32 W, 200 W, and 1,500 W.     

A Fast Computation Method in Frequency Domain for Power Ground Plane Impedance Calculation Using the Mobius Transform

A new method to reduce the computation time in power/ground-plane analysis is proposed. The proposed method is based on an approximation of impedance in the frequency domain using Mobius transform. The power/ground plane impedance is transformed by Mobius transform and is more linear than the raw impedance, which ensures that a simple approximation is possible. After the approximation, an inverse Mobius transform is applied to predict the power/ground plane impedance. This method displays the high speed of computing with good accuracy. In the case of impedance calculation for a 17.78 cm times 10.16 cm printed circuit board (PCB) board, the proposed method has shown to be 12 times faster than conventional methods. This method can be applied to the analysis and design of power/ground-plane where complex computation is needed.     

A 400-mA current-mode buck converter with a self-trimming current sensing scheme

A current-programmed mode (CPM) controller is designed for improved DC–DC converter control. The key building block of the CPM controller is an accurate current-sensing circuit. This paper proposes a lossless current-sensing technique to measure the inductor current by measuring the current through the power transistor. A self-trimming circuit is used to compensate for any inaccuracies caused by voltage and temperature variations. The measurement results validate the operation of the fabricated chip.     

The Effects of Management Traffic on the Local Call Processing Performance of ATM Switches Using Queue Network Models and Jackson's Theorem

This paper considers a TMN‐based management system for the management of public ATM switching networks using a four‐level hierarchical structure consisting of one network management system, several element management systems, and several agent‐ATM switch pairs. Using Jackson's queuing model, we analyze the effects of one TMN command on the performance of the component ATM switch in processing local calls. The TMN command considered is the permanent virtual call connection. We analyze four performance measures of ATM switches—utilization, mean queue length and mean waiting time for the processor directly interfacing with the subscriber lines and trunks, and the call setup delay of the ATM switch—and compare the results with those from Jackson's queuing model.     

Development of a biodegradable sirolimus-eluting stent coated by ultrasonic atomizing spray

In this study, poly(D,L lactic-co-glycolic acid) (PLGA) was used as a drug carrier to generate two types of stents loaded with different concentrations of sirolimus. These stents were prepared by ultrasonic atomizing spray coating. Ultrasonic atomizing spray nozzle uses a low-pressure air/gas to produce a soft, highly focused beam of small spray drops. An isolated hypotube delivers liquid to the nozzle's atomizing surface while air/gas, delivered through the nozzle orifice at a fixed low pressure, shapes the atomized drops into a very precise, targeted spray. The stent was moved both in the traverse direction and rotated during the spraying process. The morphology of the sirolimus-eluting stents was examined by scanning electron microscopy (SEM) which indicated that the coating was very smooth and uniform. The coating was found to have the ability to withstand the compressive and tensile strains imparted without cracking during the stent inflation process. Release profile of sirolimus was measured by high performance liquid chromatography (HPLC). The release behavior of sirolimus from the stent surface had a two phase release profile with a burst release period of about 2 days, followed by a sustained and slow release phase. The mass loss behavior of PLGA appeared linear throughout most of the degradation period. At 28 days, neointimal formation was found to be significantly decreased for both sirolimus-eluting stents as compared to bare-metal stents (BMS). Assessment of vascular healing revealed an absence of increased inflammation in both sirolimus-eluting stents. Inflammation is commonly observed in drug-eluting stents (DES) with nonbiodegradable polymeric coatings. Taking these results into account, these novel sirolimus-eluting stents may be good candidates to resolve in-stent restenosis.