Application of differential quadrature to static analysis of structural components

The numerical technique of differential quadrature for the solution of linear and non-linear partial differential equations, first introduced by Bellman and his associates, is applied to the equations governing the deflection and buckling behaviour of one- and two-dimensional structural components. Separate transformations are used for higher-order derivatives, as suggested by Mingle, thus extending the method to treat fourth-order equations and to include multiple, boundary conditions in the respective co-ordinate directions. Results are obtained for various boundary and loading conditions and are compared with existing exact and numerical solutions by other methods. The application of differential quadrature to this class of problems is seen to lead to accurate results with relatively small computational effort.     

Low-power CSD linear phase FIR filter structure using verticalcommon sub-expression

A high-speed/low-power canonic signed digit (CSD) linear phase finite impulse response (FIR) filter structure using vertical common sub-expression is proposed. In the conventional linear phase CSD filter, the horizontal common sub-expression method (see Hartley, 1996) has been widely utilised due to the inherent symmetrical filter coefficients. However, use has been made of the fact that the most significant bits of adjacent filter coefficients in the linear phase filter are also equal since they have mostly similar values. Through the example, it is shown that the proposed structure is more efficient in the case where bit precision of implementation is lower     

Selective and nonselective wet etching of Zn0.9Mg0.1O/ZnO

Wet etch rates at 25°C for Zn_0.9Mg_0.1O grown on sapphire substrates by pulsed laser deposition (PLD) were in the range 300–1100 nm · min⁻¹ with HCl/H₂O (5×10⁻³−2×10⁻² M) and 120–300 nm · min⁻¹ with H₃PO₄/H₂O (5×10⁻³−2×10⁻² M). Both of these dilute mixtures exhibited diffusion-limited etching, with thermal activation energies of 2–3 kCal · mol⁻¹. By sharp contrast, the etch rates for ZnO also grown on sapphire by PLD were much slower in similar solutions, with rates of 1.2–50 nm · min⁻¹ in HCl/H₂O (0.01–1.2 M) and 12–54 nm · min⁻¹ in H₃PO₄/H₂O (0.02–0.15 M). The etching was reaction limited over the temperature range 25–75°C, with activation energies close to 6 kCal · mol⁻¹. The resulting selectivity of Zn_0.9Mg_0.1O over ZnO can be a high as ∼400 with HCl and ∼30 with H₃PO₄.     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Microstructural investigation of long-term degradation mechanisms in GFRP dowel bars for jointed concrete pavement

Steel dowel bar is used to transfer loads in concrete pavement slab. However, once the steel dowel bar corrodes, it may cause faults, such as joint freezing in concrete pavement, level differences resulting from spalling or decreased efficiency of load transfer, etc., which are the same problems experienced by typical reinforcing steel. This study evaluated the applicability of glass fiber-reinforced polymer (GFRP) dowel bar as a substitute for steel dowel bar. A microstructural analysis was conducted to examine the decrease in durability of GFRP dowel bar exposed to deterioration environments. To analyze the deterioration mechanism of GFRP dowel bar, scanning electron microscopy was employed and the porosity was measured by the gas absorption method. It was concluded that the longer the GFRP dowel bar was exposed to deterioration environments, the more the interlaminar shear stress decreased. This result was validated by the microstructural analysis. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Integrated modelling under uncertainty in watershed-level assessment and management.

Uncertainty in water quality model predictions is inevitably high due to natural stochasticity, model uncertainty, and parameter uncertainty. An integrated modelling system (modified-BASINS) under uncertainty is described and demonstrated for use in receiving-water quality prediction and watershed management. A Monte Carlo simulation was used to investigate the effect of various uncertainty types on output prediction. Without pollution control measures in the watershed, the concentrations of total nitrogen (T-N) and total phosphorus (T-P) in the Hwaong Reservoir, considering three uncertainty types, would be less than about 4.4 and 0.23 mg L(-1), respectively, in 2012, with 90% confidence. The effects of two watershed management practices, wastewater treatment plants (WWTP) and constructed wetlands (WETLAND), were evaluated. The combined scenario (WWTP + WETLAND) was the most effective at improving reservoir water quality, bringing concentrations of T-N and T-P in the Hwaong Reservoir to less than 3.4 and 0.14 mg L(-1), 24 and 41% improvements, respectively, with 90% confidence. Overall, the Monte Carlo simulation in the integrated modelling system was practical for estimating uncertainty and reliable in water quality prediction. The approach described here may allow decisions to be made based on the probability and level of risk, and its application is recommended.     

一种微机控制的多测头凸轮轴测量系统

本文介绍一种由机械装置，高精度圆光栅编码器，光栅位移传感器，微型计算机，接口控制电路等组成的多测头凸轮轴测量系统，该系统安装调整方便，定位准确，测量精度高，操作简单，工作可靠，能快速实现对凸轮轴的自动测量。