Enhancement of fibroblastic proliferation from photoreactive starch with immobilized epidermal growth factor

Carboxymethyl starch was modified by the incorporation of an azidophenyl group to prepare photoreactive starch, and characterized by Fourier transform infrared reflectance (FT‐IR), proton nuclear magnetic resonance (¹H‐NMR), and ultraviolet (UV) spectroscopy. Photo‐irradiation immobilized the Az‐starch on a polystyrene plate and it was stably retained on the surface. The protein containing immobilized Az‐starch was also immobilized on a stripe micropatterned plate. UV irradiation time and Az‐starch concentration were used to alter the physical properties of Az‐starch and consequently control the rate of epidermal growth factor (EGF) release. The Az‐starch that released growth factor was not cytotoxic to 3T3‐L1 fibroblast cells, and the immobilized EGF maintained its activity and induced cellular proliferation in vitro. These results suggest that Az‐starch could be useful as a clinical synthetic material for medical applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and optimization of NASICON-type Li3V2(PO4)3 by adipic acid-mediated solid-state approach

We report the synthesis and optimization of NASICON-type carbon-coated Li₃V₂(PO₄)₃ by solid-state approach. Adipic acid (AA) is used as the source material for the carbon. Initially, the synthesis of monoclinic Li₃V₂(PO₄)₃ is optimized at a precalcination temperature of 300 °C for 4 h and 900 °C for 8 h under Ar flow to yield a single phase. Powder characterizations such as thermogravimetric–differential thermal analysis, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and particle size distribution are conducted, and the results are presented. The AA concentration is varied according to the total metal ion composition in the compound (0.05, 0.1, and 0.15 M). Electrochemical Li-insertion properties are evaluated in half-cell configurations between 3 and 4.8 V vs. Li at a current density of 0.1 mA cm^?2 at room temperature. Compared with the lower AA concentrations, Li/Li₃V₂(PO₄)₃ (0.15 M AA) cell exhibited discharge capacities of 178 and 147 mAh g^?1 for the 1st and 50th cycles, respectively, and a capacity retention of 83 % after 50 cycles, which is 11 % higher than that of the native compound. Li/Li₃V₂(PO₄)₃ (0.15 M AA) showed better rate performances and delivered discharge capacities of 173, 165, 150, 132, 105, and 76 mAh g^?1 at rates of 0.1, 0.2, 0.5, 1, 5, and 12 C, respectively. Electrochemical impedance spectroscopy reveals the enhancement in electronic conductivity profile after carbon coating.     

Effect of Sintering Temperature on Thermoelectric Properties of p‐Bi2Te3 Alloys Produced by Gas Atomization

In this research, p‐type Bi₂Te₃–75% Sb₂Te₃ thermoelectric alloy powders were produced by gas atomization and subsequently sintered by hot pressing at different temperatures. The grain growth of the hot‐pressed samples was observed with increasing sintering temperature from 380°C to 460°C. The compressive strength increased with increasing hot‐pressing temperature due to the high relative density of bulk samples obtained at high temperatures. The effect of sintering temperature on thermoelectric (TE) properties was studied. The maximum power factor 3.48 mW/mK² was obtained for the sample hot pressed at 420°C due to the resulting high electrical conductivity and enhanced Seebeck coefficient values.     

Effect of processing conditions and reactive compatibilizer on the morphology of injection molded modified poly(phenylene oxide)/polyamide‐6 blends

The effect of injection molding conditions and reactive compatibilization on the morphology of maleic anhydryde‐modified poly(phenylene oxide)/polyamide‐6 blends was investigated. The injection flow rate primarily influenced the position of the subskin layer, and the injection temperature affected the aspect ratio of the dispersed phase. A reduction of the sue of the dispersed phase occured during the converging flow in the barrel‐to‐sprue zone. The reactive compatibilization reduced the flow induced deformation, the coalescence and the breakup of particles and improved the dispersion of the minor phase.     

Molecular characterization of statistical copolymers: 1. Potential and limitations of full adsorption–desorption procedure in separation of statistical copolymers

Dynamic integral desorption isotherms for a series of poly(methyl methacrylate) homopolymers and poly(methyl methacrylate)–polystyrene statistical copolymers were measured. Nonporous silica was the full adsorption–desorption (FAD) column packing and various adsorption‐promoting and desorption‐promoting liquids were used. The aim of this study was to evaluate the applicability of the FAD approach for separation of statistical copolymers. The effects of the adsorbing liquid and desorbing liquid nature were demonstrated on the positions and shapes of desorption isotherms. The desorption isotherms also strongly depended on both (co)polymer molar mass and copolymer chemical composition. This indicates large fractionation potential of the FAD procedure. Simultaneously, the interference of both above parameters prevents the direct use of FAD for fractionation of the copolymers. It is anticipated that the fractionation and/or reconcentration potential of the FAD procedure can be very effectively utilized in combination of FAD with size‐exclusion chromatography and/or with gradient elution liquid adsorption chromatography. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 857–864, 2000     

Polypyrrole composite membrane with high permeability prepared by interfacial polymerization

Novel polypyrrole (PPy)/polydimethylsiloxane (PDMS) composite membrane was prepared by interfacial polymerization to make a very effective gas separation membrane. We found that Polymerized PPy films as thin as ～200 nm could be chemically synthesized as freestanding membranes by using the interfacial polymerization technique. Additionally, we show that difference morphology of PPys films was obtained by controlling polymerization rate and more dense films were formed at low polymerization rate. Wide X-ray diffraction study showed the d spacing value of the PPy film decreased from 4.89 å to 3.67 å by the rate of polymerization decreases. According to d spacing value decrease, selectivity of a PPy composite membrane was increased dramatically and permeability was reduced gradually. This high selectivity was derived from d spacing closed to the kinetic diameter of nitrogen. These results indicated that the permeability is controlled by the diffusion coefficient, reflecting the packed structure of the PPy film. The highest selectivity value of composite membrane that was prepared by interfacial polymerization was O₂/N₂=17.2 and permeability for O₂ was 40.2 barrer.     

Electron spin resonance of thin films of organic light-emitting material tris(8-hydroxyquinoline) aluminum doped by magnesium

We have successfully observed electron spin resonance (ESR) signals of radical anions in thin films of tris(8-hydroxyquinoline) aluminum (Alq₃), a compound widely used as electron transporting and luminescent layers in organic light-emitting diodes. To obtain definitely defined radical-anion states in Alq₃, we doped Alq₃ with Mg by co-evaporating these materials. The obtained g value and peak-to-peak ESR linewidth ΔH_pp of Alq₃ radical anions are 2.0030 and 2.19 mT, respectively. Theoretical g value and hyperfine interactions were calculated by density functional theory method, which are in good agreement with the experimental results. A quantitative evaluation of doping concentration was performed. We confirmed that doped charges are localized at deep trapping sites by the lineshape analysis and temperature dependence of the ESR signals. Morphological investigation using transmission electron microscopy clarified that the co-evaporated Mg atoms form clusters.     

Ring-opening polymerization of ?-caprolactone by poly(propyleneglycol) in the presence of a monomer activator

The ring-opening polymerization of ?-caprolactone (CL) was induced by using polypropylene glycol (PPG) as an initiator in the presence of the monomer activator HCl·Et₂O to synthesize triblock copolymers composed of PPG and poly(?-caprolactone) (PCL). The degree of CL conversion and the molecular weight of PCL increased linearly with the polymerization time or with the feed ratio of CL to PPG in the presence of HCl·Et₂O in CH₂Cl₂ at 25 °C. The PCLs obtained had molecular weights close to the theoretical values calculated from the CL:PPG molar ratios and exhibited monomodal GPC curves with narrow polydispersity indexes. The apparent rate constant (k_app) for the polymerization of CL activated by HCl·Et₂O was greatly affected by the ratio of HCl·Et₂O/PPG. The activation energy for the polymerization of CL in this system was estimated to be 49.8 kJ/mol K. We successfully prepared PPG and PCL triblock copolymers using this activated monomer mechanism.     

Synthesis of mesoporous materials SBA-15 and CMK-3 from fly ash and their application for CO2 adsorption

A supernatant solution of silicate species extracted from coal fly ash in a power plant by alkali fusion was used in acidic condition to prepare a mesoporous silica SBA-15. The SBA-15 was used as a template for the synthesis of a mesoporous carbon CMK-3 using sucrose as a carbon source. Characterization of the produced mesoporous materials by XRD, N₂ adsorption-desorption, SEM, and TEM confirmed the formation of well-ordered hexagonal mesostructures. Textural properties were found close to those prepared by pure chemicals. SBA-15 after polyethyleneimine impregnation and CMK-3 were tested for carbon dioxide adsorption, successfully demonstrating the possibility of recycling the industrial waste product in a power plant into a useful adsorbent.     

Preparation of platinum-doped hollow spheres and their electrocatalytic activity in water electrolysis

Pure TiO₂ hollow spheres were prepared by using poly(styrene-methacrylic acid) latex particles as template; thereafter, titania hollow spheres were coated by platinum with an appropriate amount of choloroplatinic acid solution to obtain Pt/TiO₂ catalysts. The morphology and structure of nonstructural Pt/TiO₂ hollow spheres were characterized by BET, XRD, TGA, SEM and TEM analysis. In the samples, a remarkably uniform layer of Pt consisting of particles from 5 to 70 nm in size was formed over TiO₂ hollow spheres. We found the electrocatalytic nature of the samples by cyclic voltammetric experiment in acidic solution. The anodic peak current density of 20 wt% Pt-loaded TiO₂ hollow particles was observed 2.5 times higher than that of 5 wt% Pt/TiO₂ in the same experimental condition. Also, the anodic current density of 20 wt% Pt/TiO₂ hollow spheres calcined at various temperatures followed the order: 400 °C≈500 °C>600 °C. The electrocatalytic activity of the Pt-loaded TiO₂ hollow spheres depends on the amount of atomic platinum present in the sample; a higher concentration of platinum results in a larger current density value in anodic sweep, resulting in more oxygen production during electrolysis. Pt/TiO₂ hollow sphere catalysts have also shown long term electrocatalytic stability in acidic media.