Liquid phase sintering of hydroxyapatite by phosphate and silicate glass additions: structure and properties of the composites

Phosphate- and silicate-based glasses were added to hydroxyapatite in order to improve its mechanical properties and to fabricate composites with different degrees of bioactivity. A strong chemical bonding was obtained between hydroxyapatite and the phosphate-based glasses leading to samples approaching theoretical density, according to density measurements and scanning electron microscopy. Bioglass^® additions led to the formation of a complex calcium phosphate silicate which hampered the reinforcement process. The fracture toughness of the hydroxyapatite-glass composites was shown to be within the 1.1–1.2 MPam^1/2 range, which is double that determined for sintered hydroxyapatite. A 2 m thick apatite layer was observed on the surface of the hydroxyapatite-glass composites after 48 h immersion in a simulated human blood plasma, whereas only a few apatite crystals were detected on sintered hydroxyapatite after 7 days immersion. From the results obtained we anticipate that the composites might show a higher rate of bone bonding, leading to enhanced bioactivity.     

How can Cleaner Production practices contribute to meet ISO 14001 requirements? Critical analysis from a survey with industrial companies

The companies’ needs to adopt changes in their way of production to maximize the environmental performance required by their stakeholders, and at the same time, to maximize their economic and market performance, have made them seek for environmental strategies and certifications. In this sense, the Cleaner Production and the Environmental Management System based on ISO 14001 have been, respectively, presented, since the main objective of this research is to identify and analyze Cleaner Production contributions to comply with ISO 14001 requirements. For such, a survey research has been carried out in Brazilian industrial companies certified by ISO 14001. We have identified the main performance factors by leading practices and variables of Cleaner Production that contribute to the compliance with the standard requirements by companies. Thus, it has been noted that Cleaner Production is an important strategy for the preparation of companies for certification as well as for improving their environmental performance.     

Topology optimization of continuum structures subjected to uncertainties in material properties

This work addresses the use of the topology optimization approach to the design of robust continuum structures under the hypothesis of uncertainties with known second‐order statistics. To this end, the second‐order perturbation approach is used to model the response of the structure, and the midpoint discretization technique is used to discretize the random field. The objective function is a weighted sum of the expected compliance and its standard deviation. The optimization problem is solved using a traditional optimality criteria method. It is shown that the correlation length plays an important role in the obtained topology and statistical moments when only the minimization of the standard deviation is considered, resulting in more and thinner reinforcements as the correlation length decreases. It is also shown that the minimization of the expected value is close to the minimization of the deterministic compliance for small variations of Young's modulus. Copyright © 2016 John Wiley & Sons, Ltd.     

Structural damage identification via time domain response and Markov Chain Monte Carlo method

The present work addresses the problem of structural damage identification built on the statistical inversion approach. Here, the damage state of the structure is continuously described by a cohesion parameter, which is spatially discretized by the finite element method. The inverse problem of damage identification is then posed as the determination of the posterior probability densities of the nodal cohesion parameters. The Markov Chain Monte Carlo method, implemented with the Metropolis–Hastings algorithm, is considered in order to approximate the posterior probabilities by drawing samples from the desired joint posterior probability density function. With this approach, prior information on the sought parameters can be used and the uncertainty concerning the known values of the material properties can be quantified in the estimation of the cohesion parameters. The assessment of the proposed approach has been performed by means of numerical simulations on a simply supported Euler–Bernoulli beam. The damage identification and assessment are performed considering time domain response data. Different damage scenarios and noise levels were addressed, demonstrating the feasibility of the proposed approach.     

Coupled temperature and moisture effects on the tensile behavior of strain hardening cementitious composites (SHCC) reinforced with PVA fibers

This paper reports the experimental findings on the tensile behavior of strain-hardening cement-based composites (SHCC). The composites were subjected to the combined effects of elevated temperatures and internal moisture condition. Uniaxial tensile tests on dumbbell-shaped SHCC specimens with in situ temperature control were performed at 22, 60 and 100 °C. In addition, the effect of the internal humidity of SHCC (95, 50, 20 and 0%) coupled to the elevated temperatures was investigated. It was shown that the tensile strength decreases and the strain capacity increases with an increase in temperature. The influence of the internal moisture conditions was more significant in high temperatures. The strain capacity reduced significantly with a decrease in the humidity level. The crack pattern of the SHCC specimens was determined. Furthermore, single fiber pullout tests were performed under the considered high temperatures condition. Finally, the results are discussed based on the thermogravimetry analysis of the PVA fiber, alterations on its microstructure and surface coating.     

Bulk mass flow in a vibratory finisher: mechanisms and effect of process parameters

Vibratory finishing is a widely-used manufacturing process in which a vibrating container filled with granular media becomes fluidized. The resulting bulk flow entrains workpieces and exposes their surfaces to the impacts resulting from the small-scale media vibrations. The bulk flow is responsible for entrainment and mixing, while the media vibration does work on the surfaces. The selection of machine vibration parameters is commonly based on experience due to the difficulty in predicting the fluidized bed behavior. In this work, a discrete element method was used to investigate how the bulk flow in an actual tub finisher filled with steel balls depends on the tub motion parameters through a parametric study. The underlying mechanisms that create and drive the bulk flow were identified by examining the relationships between the bulk flow rates and the wall forces. Finally, the connection between the wall motion and the wall forces was investigated. The tub frequency was the most effective control parameter and there was an optimal phase difference between the horizontal and vertical vibrations to maximize bulk flow. The relationship between the media packing at the walls and the tangential forces between the walls and the media explained the formation and speed of the bulk flow. Lastly, it was shown that the tangential wall forces, unlike the normal forces, cannot be obtained from the known wall motion alone since they also depend on the media velocities relative to the walls.     

Influence of process parameters on average particle speeds in a vibratory finisher

Vibratory finishing (VF) employs vibrationally-fluidized granular media to finish the surfaces of workpieces that are entrained in the flowing media. Its application has been based mostly on experience and trial-and-error due to the complexity of the granular material behavior. The present study used discrete element modeling (DEM) to investigate how the movement of a commercial two-dimensional tub finisher influenced the average particle speed of the media in a bed of smooth, steel, spherical particles, and thus the work that would be done on an entrained workpiece. The parameters governing the tub wall motion (frequency, in-plane amplitudes, and phases of vibration) and the coefficient of friction between the media and the wall were systematically varied in 71 three-dimensional DEM simulations. The average particle speed was affected mostly by the vertical amplitude of tub motion rather than by the frequency, and was mostly independent of other parameters of motion and of the wall friction. A strong relationship was found between the average particle speed and the work done by the wall per cycle of vibration. The normal force on the wall was also found to correlate strongly with the normal component of the wall velocity. Together, these relationships offer the potential to enable the analytical prediction of the average particle speed based on the motion parameters of the tub alone. The paper provides a set of practical guidelines for the control of the average particle speed in VF that are explained by the forces between the media and walls of the tub finisher.