100-Gb/s DQPSK Transmission Experiment Without OTDM for 100G Ethernet Transport

In order to realize a future 100-Gb Ethernet (100 GbE) transport, 100-Gb/s transmission without 100-GHz-class electronics and optical time-division-multiplexing technique was demonstrated. By using a differential quadrature phase-shift-keying (DQPSK) modulation format and commercially available electronics, 2- and 50-km transmissions of 100-Gb/s signal were successfully achieved over a standard single mode fiber. The receiver sensitivity, chromatic dispersion, and differential group delay tolerances of 100-Gb/s DQPSK signal were also evaluated. Through these evaluations, the possibility of DQPSK modulation for future 100-GbE transport is verified     

An Analytical Compact Circuit Model for Nanowire FET

In this paper, we propose a quasi-analytical device model of nanowire FET (NWFET) for both ballistic and drift-diffusion current transport, which can be used in any conventional circuit simulator like SPICE. The closed form expressions for current-voltage (I-V) and capacitance-voltage characteristics are obtained by analytically solving device equations with appropriate approximations. The developed model was further verified with the measured I-V characteristics of an NWFET device. Results show a close match of the model with measured data.     

Enhanced path smoothing based on conjugate gradient descent for firefighting robots in petrochemical complexes*

The firefighting robot system (FFRS) comprises several autonomous robots that can be deployed to fire disasters in petrochemical complexes. For autonomous navigation, the path planner should consider the robot constraints and characteristics. Specifically, three requirements should be satisfied for a path to be suitable for the FFRS. First, the path must satisfy the maximum curvature constraint. Second, it must be smooth for robots to easily execute the trajectory. Third, it must allow reaching the target location in a specific heading. We propose a path planner that provides smooth paths, satisfy the maximum curvature constraint, and allows a suitable robot heading. The path smoother is based on the conjugate gradient descent, and three approaches are proposed for this path planner to meet all the FFRS requirements. The effectiveness of these approaches is qualitatively and quantitatively evaluated by examining the generated paths. Finally, the path planner is applied to an actual robot to verify the suitability of the generated paths for the FFRS, and planning is applied to another type of robot to demonstrate the wide applicability of the proposed planner.     

Suppression of interface degradation in InGaAsP inP buried heterostructure lasers

In InGaAsP/InP buried heterostructure (BH) lasers, the degradation of BH interface between first- and second-growth step layers can be suppressed by employing the melt back process just before the second-step layer growth. It is confirmed this burying process give more reliable BH lasers than the conventional burying process. From the viewpoint of BH interface degradation, lasers lasing at 1.5 μm, where the melt back process naturally occurs during BH formation, are found to be more reliable than those lasing at 1.3 μm.     

Heat extraction characteristics by coaxial heat exchanger

This study was performed to investigate the heat extraction characteristics from shallow geothermal resources using a coaxial heat exchanger. First, a computer simulation program for a coaxial heat exchanger was checked and verified by laboratory experiments. After inspecting the effectiveness of the computer program described herein, a numerical simulation for a real scale model was conducted under the condition that the heat transfer mechanism in the stratum was heat conduction. Unsteady heat extraction characteristics are presented herein, and the effects of the tube material, inner diameter, and circular modes on the heat extraction rate are discussed. From the computer results it was found that the heat extraction performance using a coaxial heat exchanger greatly depended on the factors mentioned above in the range of the parameters covered in this study. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(7): 496–513, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20083     

Measurement of charge carrier's transportation in a large size self-standing CVD single crystal diamond film fabricated using lift-off method

Using lift-off method, we synthesized large self-standing plasma CVD diamond films on various substrates. Charge carrier transportation in diamond was measured using α particle measurements and TOF methods with a short-pulsed UV laser. The high-quality films were synthesized rapidly. We observed the maximum transit time of holes and electrons shorter than 5 ns. The lift-off method is useful to fabricate the high-quality diamond with excellent drift velocities of the charge carrier. The charge transport characteristics of our diamond films are comparable to those of a commercially available (Element Six Ltd.) electronics grade IIa diamond single crystal.     

Densification of rare-earth (Lu, Gd, Nd)-doped alumina nanopowders obtained by a sol-gel route under seeding

Rare-earth (RE: Lu, Gd, Nd, 0.10 mol%)-doped alumina nanopowders were prepared by a new sol-gel route using polyhydroxoaluminum (PHA) and RECl₃ solutions under α-alumina (∼ 75 nm) seeding. Among the rare-earth dopants studied, Lu yields the most suitable nanopowders for low-temperature densification. The 0.10 mol% Lu-doped nanopowders, which were obtained at a calcination temperature of 900 °C under 5 mass% α-alumina seeding, consisted of ∼ 80-nm α-alumina particles and γ-alumina nanoparticles. Using these Lu-doped alumina nanopowders, fully densified alumina ceramics with a uniform microstructure composed of fine grains with an average size of 0.61 μm could be obtained at 1400 °C by pressureless sintering. Clearly, the Lu-doped nanopowders obtained here represent a viable option for fabricating dense, finer-grained alumina ceramics because an undoped sample with 5 mass% seeds gave a microstructure with an average grain size of 1.78 μm at 1400 °C.     

Guided-wave acoustooptic interaction with phase modulation in a ZnOthin-film transducer on an Si-based integrated Mach-Zehnderinterferometer

This paper presents the design and the realization of a novel integrated Mach-Zehnder interferometer (MZI) with heterodyne scheme. Well-controlled machining as well as ZnO thin-film transducer integration on the same Si substrate permits to transform an optically passive device to an active device with sinusoidal phase modulation. Theoretical and experimental results are presented, demonstrating that an efficient sensor can be designed and fabricated     

A New Nonmetallic Inclusion Rating Method by Positive Use of Hydrogen Embrittlement Phenomenon

A new inclusions rating method using hydrogen embrittlement of a tensile test specimen is proposed. This method is essentially based on the statistics of extremes for inclusion rating where the maximum inclusion size is determined by simple tensile testing of a hydrogen-precharged (H-precharged) specimen. Tensile tests were conducted using two bearing steels (SAE52100 HV 346, HV 447, HV 559, HV 611, HV 678 and ASTM-A485-1 HV 706, HV 715) and one spring steel (SAE5160, HV 651). Fatigue tests were conducted using SAE52100 bearing steel (HV 682). All H-precharged tensile specimens (SAE52100, ASTM-A485-1 and SAE5160) were fractured from internal inclusions except the SAE52100 tensile specimens with a Vickers hardness of HV 346. It was confirmed that the distribution of extreme values of inclusion sizes obtained by SAE52100 tensile testing with H-precharged specimens coincided with those obtained by SAE52100 fatigue testing. From these results, it is presumed that the inclusion rating method by fatigue testing can be replaced by simple tensile testing with H-precharged specimens. The proposed method is more convenient and reliable than other existing inclusion rating methods, i.e., fatigue testing and optical microscopy. The proposed method can be applied to specimens with a Vickers hardness of higher than HV 447.     

High-pressure solubility of fullerene C60 in toluene

The solubility of fullerene C₆₀ in toluene was measured at temperatures between 278.2 and 308.2 K and pressures up to 340 MPa, and also at temperatures between 258.2 and 298.2 K under atmospheric pressure. The solubility increased with increasing pressure, and then decreased with a sharp maximum, suggesting a transition between solid phases. A thermodynamic analysis of the solubility supported the proposal of Korobov, et al. that the two solids correspond to C₆₀ (fcc) and C₆₀ · 2 (toluene) solvate. The solubility enhancement of C₆₀ by pressure in a low-pressure region is an unusual phenomenon when compared with the decrease in solubility of nonpolar molecular solids generally observed with rises in pressure.