Barium hexaferrite magnet by topotactic reaction method

A new topotactic sintering method using Fe₂O₃ (obtained from FeO · OH) and BaCO₃ is developed for preparing cheaper grain oriented barium hexaferrite. Fe₂O₃ and BaCO₃ (precipitate grade) are wet mixed in a ball mill in stoichiometric proportion. The mixed slurry is then dried at 110° C for about 12h. The dried powder mixture containing moisture as a binder is uniaxially compacted at 5×10⁶–10×10⁶ kg m^–2 pressure. The green compacts are air sintered in the temperature range 1100–1300° C for 1 H. The best results of the sintered ferrite show maximum energy product (BH) _max in the range 7–10 kTAm^–1. The bulk of commercial requirements for toy magnets etc. may be met by this method of production which eliminates steps like calcination and cost intensive wet magnetic compaction.     

Solution precursor plasma deposition of nanostructured ZnO coatings

Zinc oxide (ZnO) is a wide band gap semiconducting material that has various applications including optical, electronic, biomedical and corrosion protection. It is usually synthesized via processing routes, such as vapor deposition techniques, sol-gel, spray pyrolysis and thermal spray of pre-synthesized ZnO powders. Cheaper and faster synthesis techniques are of technological importance due to increased demand in alternative energy applications. Here, we report synthesis of nanostructured ZnO coatings directly from a solution precursor in a single step using plasma spray technique. Nanostructured ZnO coatings were deposited from the solution precursor prepared using zinc acetate and water/isopropanol. An axial liquid atomizer was employed in a DC plasma spray torch to create fine droplets of precursor for faster thermal treatment in the plasma plume to form ZnO. Microstructures of coatings revealed ultrafine particulate agglomerates. X-ray diffraction confirmed polycrystalline nature and hexagonal Wurtzite crystal structure of the coatings. Transmission electron microscopy studies showed fine grains in the range of 10-40 nm. Observed optical transmittance (∼65-80%) and reflectivity (∼65-70%) in the visible spectrum, and electrical resistivity (48.5-50.1 mΩ cm) of ZnO coatings are attributed to ultrafine particulate morphology of the coatings.     

Psychobiotics: A new approach for treating mental illness?

Gut microbiomes may have a significant impact on mood and cognition, which is leading experts towards a new frontier in neuroscience. Studies have shown that increase in the amount of good bacteria in the gut can curb inflammation and cortisol level, reduces symptoms of depression and anxiety, lowers stress reactivity, improves memory and even lessens neuroticism and social anxiety. This shows that, probably the beneficial gut bacteria or probiotics function mechanistically as delivery vehicles for neuroactive compounds. Thus, a psychobiotic is a live organism, when ingested in adequate amounts, produces a health benefit in patients suffering from psychiatric illness. Study of these novel class of probiotics may open up the possibility of rearrangement of intestinal microbiota for effective management of various psychiatric disorders.     

Microstructural investigation on mechanical behavior of soil-geosynthetic interface in direct shear test

Interface shear strength between soil and geosynthetics mainly depends on the mechanical and physical properties of soil, geosynthetics and the normal stress acting at the interface. This paper presents results of an extensive experimental investigation carried out on sand-geosynthetic interface using modified large direct shear box. The study focusses on the shearing mechanism at the sand-geosynthetic interface and the effect of different parameters on the shearing mechanism. Smooth HDPE geomembrane, nonwoven needle punched geotextile and two types of sand having different mean particle size, have been used in the present study. Microstructural investigation of deformed specimen through Field Emission Scanning Electron Microscope (FESEM) reveals the shearing mechanism which includes interlocking and fiber stretching for sand-geotextile while sliding, indentation and plowing for sand-geomembrane interface. The shearing mechanism for sand-geomembrane interface highly depends on the normal stress and degree of saturation of sand. The critical normal stress that demarcates the sliding and plowing mechanism for sand-geomembrane interface is different for dry and wet sand. The amount of scouring (or plowing) of the geomembrane surface reduces with increase in the mean particle size of sand. FESEM images revealed that the sand particles get adhered to the geotextile fibers for tests involving wet sands. The present microstructural study aided in understanding the shearing mechanism at sand-geosynthetic interface to a large extent.     

Laminar free convection in open-ended vertical 7-rod bundles: experiments and porous model

The flow of ambient air induced solely by buoyancy, through a vertical rod bundle has been modelled as a phenomenon in a porous medium. The rods are at uniform heat flux condition and the circular shell adiabatic. The induced flow rate was found to be controlled by a parameter ψ dependent on the heat flux, rod diameter, length, fluid properties and the bundle permeability. Measurements performed on two 7-rod bundles corroborate the theoretical predictions. Longitudinally averaged heat transfer rates from the central and peripheral rods have also been measured and average information generated for the bundle.     

Observer design for differential difference systems

Sufficient conditions for a full order observer design for deterministic linear time-invariant differential difference systems is suggested. The observer parameters are constrained so that its coefficient matrices corresponding to delayed and nondelayed states commute. Then, a desired degree of stability for the observer can be achieved.     

Effect of chemical modification on FTIR spectra. I. Physical and chemical behavior of coir

Coir fibers were chemically modified through alkali treatment, and crosslinking with formaldehyde, para-phenylene diamine, phthalic anhydride, and combined crosslinking-cyanoethylation reactions in appropriate solvent and catalyst. The parent and chemically modified coir were characterized by FTIR spectra. The percent moisture regain, tensile strength, and behavior toward some chemical reagents (solubility %) of parent and chemically modified fibers have also been evaluated. The modified fibers showed significant hydrophobicity, improved tensile strength, and good chemical resistance. © 1995 John Wiley & Sons, Inc.     

Sustainable biocarbon as an alternative of traditional fillers for poly(butylene terephthalate)-based composites: Thermo-oxidative aging and durability

Sustainable biocomposites have gained considerable interest as an alternative to conventional composites in recent years due to their cost-effectiveness and environmental friendliness. The aim of this study was to investigate the performance and durability behavior of biocomposites from sustainable biocarbon (BC) as compared to conventional established fillers. The poly(butylene terephthalate) (PBT) and its composites reinforced with BC, talc, and glass fiber (GF) were prepared and the durability performances was investigated. The study showed that BC/PBT biocomposites provided a lighter weight alternative to traditionally used fillers. After undergoes thermo-oxidative aging, the mechanical properties of BC/PBT biocomposite were deteriorated. The GF/PBT showed the most stable in retaining its mechanical properties in comparison to the talc/PBT and BC/PBT. The aging behavior and mechanism of the PBT composites were discussed. This study provides further insight on the durability-related properties progression of biocomposites as compared to traditional used fillers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47722.     

Processable high Tg high strength fluorinated new poly(arylene ether)s containing imido aryl group

A series of poly(arylene ether)s ( 7a–7f ) were successfully synthesized by aromatic nucleophilic substitution reactions of imidoaryl biphenol (5), 4,9‐bis‐(4‐hydroxy‐phenyl)‐2‐phenyl‐benzo[f]isoindole‐1,3‐dione with six different trifluoromethyl substituted bisfluoro monomers ( 6a–6f ). The weight‐average molar masses of the polymers were up to 280 kD as measured by GPC. These poly(arylene ether)s exhibited glass transition temperatures up to 361°C in DSC. These polymers showed very high thermal stability up to 558°C for 10% weight loss under synthetic air in TGA. Except 7d–7f, remaining polymers 7a–7c were soluble in a wide range of organic solvents. Transparent thin films of these polymers cast from DCM or NMP exhibited tensile strengths up to 75 MPa and elongation at break up to 41% depending on their exact repeating unit structures. These poly(arylene ether)s showed cut‐off wavelength in between 400 and 450 nm except 7d and water absorption were in the range of 0.4 to 0.6%. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011