Implementing total quality management at the U.S. Department of Defense

This paper examines Total Quality Management (TQM) as defined by Dr. W. Edwards Deming including Deming's fourteen points and explains how the United States' Department of Defense (DOD) defines TQM and why TQM is necessary. It also covers how the DOD is planning on implementing TQM and the policy that has been established as guidance in the implementation process.     

A fine-grain architecture for relational database aggregationoperations

The design and simulation of a bit-sliced processor for relational database aggregation functions, are discussed. The processor, which addresses an important, computationally expensive problem in database computers, takes two tuples as input (one bit at a time) and returns two bits as output every clock cycle. A larger aggregation unit uses a number of identical slice processors, connected according to odd-even network topology, to achieve improved performance on a parallel pipelined processor. The data processing time is completely overlapped with the input and output of data to and from the unit. The design is independent of the tuple size, and since a bit-serial computation is used, the system requires limited interconnection     

A general framework for debugging

The state of the art of debugging is examined. A debugged process model that serves as the basis of a general debugging framework is described. The relationship of the model to traditional debugging processes and support tools is discussed. A minimal set of requirements for a general debugging framework is described in terms of both the theory behind debugging methodologies and the support tools. An execution monitor, Eden, that serves as a debugging tool within this general framework is described     

Fractoemission from Lead Zirconate-Titanate

We present measurements of the electron, positive ion, and photon emission accompanying the fracture in vacuum of poly-crystalline 95/5 lead zirconate-titanate. The intensities of the charged-particle components of this fractoemission are shown to depend strongly on the direction (relative to the direction of fracture) and magnitude of polarization. The most intense emission is observed when the fracture surfaces are perpendicular to the polarization direction. The emission intensity increases monotonically with polarization. These results are interpreted in terms of a model involving charge separation on the fracture surfaces leading to a microdischarge during fracture. Implications to the interpretation of triboluminesence effects are discussed.     

Application of a multi-channel system for continuous monitoring and an early warning system.

A multi-channel continuous toxicity monitoring system developed in our laboratory, based on two-stage mini-bioreactors, was successfully implemented in the form of computer-based data acquisition. The multi-channel system consists of a series of a two-stage minibioreactor systems connected by a fiber optic probe to a luminometer, and uses genetically engineered bioluminescent bacteria for the detection of the potential toxicity from the soluble chemicals. This system can be stably and continuously operated due to the separation of the culture reactor from the test reactor and accomplish easy and long-term monitoring without system shut down by abrupt inflows of severe polluting chemicals. Four different recombinant bioluminescent bacteria were used in different channels so that the modes of the samples toxicities can be reasonably identified and evaluated based upon the response signature of each channel. The bioluminescent signatures were delivered from four channels by switching one at once, while the data is automatically logged to an IBM compatible computer. We also achieved the enhancement of the system through the manipulation of the dilution rate and the use of thermo-lux fusion strains. Finally, this system is now being implemented to a drinking water reservoir and river for remote sensing as an early warning system.     

Monitoring of human enteric viruses and coliform bacteria in waters after urban flood in Jakarta, Indonesia.

Floodwaters in Kampung Melayu village, Jakarta, Indonesia, as well as river water and consumable water (including groundwater and tap water) samples in flooded and non-flooded areas, were quantitatively analysed to assess occurrence of viruses and total coliforms and E. coli as bacterial indicators after flooding event. High numbers of enterovirus, hepatitis A virus, norovirus (G1, G2) and adenovirus were detected at high concentration in floodwaters and waters sampled from Ciliwung River which runs across metropolitan Jakarta and is used widely for agriculture and domestic purposes by poor residents. One out of three groundwater wells in the flooded area was contaminated with all viruses tested while no viruses were found in groundwater samples in non-flooded areas and tap water samples. The results revealed that human enteric viruses, especially hepatitis A virus and adenovirus, were prevalent in Jakarta, Indonesia. This study suggested that flooding posed a higher risk of viral infection to the people through contamination of drinking water sources or direct contact with floodwaters.     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Nanolayered lightweight flexible shields with multidirectional optical transparency

New nanolayered coatings are designed and deposited on flexible plastic substrate having the thickness of 100 /spl mu/m, in order to realize lightweight ultrathin transparent shielding foils. The structure of the coating is optimized considering three figures of merit: the average transmittance in the visible range for normal incidence, the normalized average transmittance for oblique incidence at 550 nm, and the transmittance quality factor. The nanotechnology exploited for the deposition of the transparent metals is the dual ion beam sputtering. Tests of durability, optical transmission, and shielding effectiveness demonstrate that the film has a high adhesion under mechanical solicitation, high resistance against aging, peak transmittance in the visible range higher than 70%, omnidirectional properties in the range 0/spl deg/-60/spl deg/, and shielding effectiveness of 40 dB up to 6 GHz.     

Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.