Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel

Comparative studies on Ar and He closed-cycle MHD power plants combined with fossil fuel are performed. The sizes of a regenerative heat exchanger and a boiler are expected to be smaller for He than for Ar. The pressure loss of a working gas in a regenerative heat exchanger is reduced for He. The purification subsystem for He is expected to be more compact and economical than that for Ar; but a larger compressor is required for He than for Ar.     

An assessment of the θ-projection method for the representation and extrapolation of creep data for a 1%Cr, 12%Mo, 14%V steel tested at 565°C

Constant stress creep data for a wrought 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel obtained from six tests carried out at 565°C have been fitted and extrapolated using the θ-projection method. Creep curves for high stresses were fitted well, but curves extrapolated to stress levels below those used in the θ-projection did not represent well the available data for primary-secondary creep. To enable a satisfactory extrapolation of results, it was found necessary to redefine the failure condition to be less sensitive to the shape of the latter sections of the tertiary creep curve. This was achieved by defining lifetime as the point on the curve at which the strain rate reached a fixed multiple of the creep rate at half the rupture time. The extrapolated data compare well with the results of tests carried out independently on a cast 1%Cr, $\text{1}\text{2}\text{\%}\text{Mo}$, $\text{1}\text{4}\text{\%}\text{V}$ steel. The extrapolation procedure not only predicts the ‘knee’ in the log stress-log lifetime curve but allows extrapolation of lifetimes by over a factor of thirty. In addition, acceptable predictions have been made of constant load experimental data.     

Kinetics of Folacin Destruction in Swiss Chard During Storage

The folacin activities in fresh Swiss chard leaves stored in open air at 4, 21, 35 and 40°C were determined by a microbiological assay using Lactobacillus casei. At 21°C the leaves were also stored in plastic bags and under moist conditions. Folacin was most stable when the vegetable was stored in plastic bags, followed by the moist condition, and least stable in open air at 21°C. The degradation of folacin in Swiss chard under all conditions followed firstorder kinetics. The temperature dependent folate degradation conformed to the Arrhenius equation and the activation energy was 24 kcal/mole.     

Wind excitation of neighbouring tall buildings

There is a growing concern about the importance of interaction effects between neighbouring tall buildings subjected to wind loading. Available results indicate that both the peak dynamic response as well as the mean wind loads may increase substantially due to building interaction.An extensive wind-tunnel study of the interaction between two square prisms with a height-to-base length equal to six was undertaken at the LAC, UFRGS. Fifteen relative prism positions were studied, for wind orientations at every 15°, under smooth-uniform as well as turbulent-shear wind. Mean force and torsional moment coefficients for uniform flow were reported in previous publications. Herein, complete results for turbulent wind are given. In addition, the most important interaction effects observed under both flow conditions are discussed in detail.     

Subdivision of work on construction projects

In order to control a project, construction management requires project information. This is obtained through accounting, estimating, cost management and scheduling functions which produce project reports. These reports are best obtained by subdividing the project into small parts. The ways in which each of these functions subdivides a project in order to produce its reports is discussed, together with a means of interrelating this information with a technique known as the work breakdown structure.     

Surface tension isotherms of a free surface and grain boundaries in the Cu-Sn system

Surface tension of pure copper and its alloys with Sn has been measured at 1000°C in a hydrogen atmosphere. Surface tension of a free surface equaled 1.81 N/m for pure copper, and 1.55, 1.38, and 1.28 N/m for the alloys with 0.05, 0.22, and 0.33 at % Sn, respectively; surface tension at grain boundaries equaled 0.5 N/m for pure copper, and 0.36, 0.3, and 0.23 N/m for the alloys, respectively. Based on these data, the concentration dependence of tin absorption at a free surface and grain boundaries has been calculated. Parameters of Sn absorption at grain boundaries and a free surface of copper have been compared with those of Sb and Bi.     

Laser scanning path generation considering photopolymer solidification in micro-stereolithography

It is essential to automate the scanning path generation process to effectively implement the micro-stereolithography. However, a scanning path that is generated based only on a 3D CAD model introduces dimensional inaccuracies. In micro-stereolithography, the photopolymer solidification is affected by fabrication conditions, such as the optical properties (laser power, laser scanning speed, laser scanning pitch focusing condition, etc.) and material properties of the photopolymer. Thus, the photopolymer solidification phenomena must be considered when generating a laser scanning path. In this paper, a scanning path generation algorithm that uses 3D CAD data and considers the photopolymer solidification phenomena is proposed to improve the dimensional accuracy in micro-stereolithography. Multi-line photopolymer solidification experiments were performed for various laser scanning conditions to examine the photopolymer solidification phenomena. From these experiments, linear relations between the solidification length (width) and scanning length (width) were acquired and stored in a database. Subsequently, these data were utilized to compensate the scanning path of the laser beam. In addition, experiments for determining the layer thickness in the z-direction were performed and these results were also used in the scanning path generation algorithm.This research was supported by the Highly Advanced National Project (http://www.most.go.kr), which performs some of the National R&D Program, and sponsored by the Korean Ministry of Science and Technology under the contract project code M10214000116-02B1500-02010.