Parallelisation of suboptimal spectrum search

The authors suggest that effective algorithms for spectrum search, such as those used for detecting spread spectrum signals, may be derived by selecting suboptimal algorithms and then recovering some of the lost efficacy through parallelisation methods. This thesis is motivated by considering a simple yet meaningful example of a spectrum search technique that exhibits what at first may seem to be counterintuitive behaviour.<>     

Dearomatization of Diesel by Solvent Extraction: Influence of the Solvent Ratio and Temperature on Diesel Raffinate Properties

To comply with the stringent environmental regulations concerning the quality of fuels the production of ultra low sulfur fuels is obligatory. Consequently, the removal of aromatics from fuels has turned to be a serious issue. This is due to the fact that the presence of aromatics in fuel deters the ultra-low sulfur fuel production. Therefore the researcher’s interest has involved the dearomatization of fuels. As a result of the dearomatization, the quality of fuels improves tremendously. Here, solvent extraction was performed to dearomatize a feedstock sample with 20.1% aromatic and 166 ppm sulfur using acetonitrile. The extraction was performed at low temperature and ambient atmospheric pressure. The aromatic contents were determined via HPLC, while the ASTM methods were employed in other parameters determination. The results showed 72% minimum yield, 8.6% aromatic content, 58–64 cetane index, 73.2 ppm sulfur content, 5.4 viscosity, RI 1.4535, aniline point 82.15, specific gravity 0.824–0.812 with API 40.32–42.88 and flash point 70–78°C. The boiling range of the produced diesel fraction raffinate (172–373°C) that corresponds to C₈–C₂₄ cuts render it a potential candidate for other petrochemical applications.     

Modest but useful erasure technique for DPSK

A simple selective erasure forward error correction (FEC) technique for differential phase shift keyed (DPSK) data is presented. The method provides a modest coding gain and requires very little overhead and computation. It is very similar to the Wagner code and may be useful as a stand alone technique in some applications and as a preconditioner to more sophisticated FEC techniques in others     

MINERALOGICAL, PORE AND PETROPHYSICAL CHARACTERISTICS OF THE DEVONIAN JAUF SANDSTONE RESERVOIR, HAWIYAH FIELD, EASTERN SAUDI ARABIA

Throughout the subsurface of the Arabian Peninsula, the approximately 460ft thick, Devonian Jauf Formation generally consists of well-compacted, low-porosity sandstones and shales, but it also includes friable and highly porous sandstones which form significant gas and condensate reservoir intervals. The mineralogy and pore properties of these reservoir intervals at the Hawiyah field (part of the giant Ghawar structure) were studied by integrating petrographic data with petrophysical measurements of reservoir sandstone samples.
The reservoir sandstones are mainly composed of quartz arenites containing small amounts of altered potassium feldspar grains, authigenic illite and chlorite. Based on the pore types, which reflect the habits of the intergranular clays, three reservoir sandstone types have been defined: Type A, characterized by macroporosity; Type B, with microporosity; and Type C, with combined laminations of Types A and B. The dominance of pore-lining clay (as in Type A) or pore-filling clay (as in Type B) is the principal factor controlling the petrophysical properties of the samples. Types A and C sandstones contain macro pores, but irreducible water saturation is high (25 to 45%) compared to clean samples elsewhere, because of the presence of micropores associated with clay. In Type B sandstones the irreducible water saturation is commonly greater than 40% because all the pores spaces are in the microporosity range. The irreducible water saturation in Type B sandstones increases rapidly as porosity decreases. When porosity is less than 10%, the corresponding permeability is 0.2 mD, but no economic production can be expected because water saturation is as high as 100%. In the producing intervals, authigenic clays result in low electrical resistivity due to high water saturation; however, water-free gas is produced.     

The impact of metal-1 plasma processing-induced hot carrierinjection on the characteristics and reliability of n-MOSFETs

We report on plasma processing-induced damage to sub-half-micron n-MOSFETs that is invoked by potential differences between device terminals during metal-1 plasma processing. The damage mechanism is identified as hot carrier (HC) injection promoted by the layout of metal-1 interconnect. Using conventional and modified charge pumping techniques as well as transistor parameter measurements, we also investigate the impact of the damage on device reliability by applying Fowler-Nordheim (FN) and hot carrier stresses. The results show the severe impact of this damage on device reliability, which is attributed to trapping of positive charge at the drain edge that is enough to shorten the device channel     

A BIST-DFT technique for DC test of analog modules

Among test techniques for analog circuits, DC test is one of the simplest method for BIST application since easy to integrate test pattern generator and response analyzer are conceivable. Precisely, this paper presents such an investigation for a CMOS operational amplifier that is latter extended to active analog filters. Since the computation of fault coverage is still a controversy question for analog cells, we develop first an evaluation technique for optimizing the tolerance band of the measurements to test. Then, using some DFT solutions we derive single DC pattern and discuss the minimal number of points to test for the detection of defects. A response analyzer is integrated with a Built-in Voltage Sensor (BIVS) and provides directly a logic pass/fail test result. Finally, the extra circuitry introduced by this BIST technique for analog modules does not exceed 5% of the total silicon area of the circuit under test and detects most of the faults.     

Error rate for optimal follower tone-jamming

The performance of a countermeasure technique in the presence of the optimal follower multitone jammer is evaluated for frequency-hopped spread spectrum (FHSS) communications. It is shown that, with a certain probability, the optimal jammer will have dual tones in a frequency channel     

Capacity analysis of a TDMA-based slow-frequency-hopped cellularsystem

Time-division multiple access (TDMA)-based systems have been adopted as the first generation digital cellular standards in North America, Europe, and Japan. The increasing demand for capacity motivates the study of alternate systems and enhancements to the adopted TDMA standards. In particular, CDMA techniques using direct sequence and slow frequency hopping have been suggested. We analyze the capacity of a slow-frequency-hopped TDMA-based cellular system via calculation of the outage probability. Expressions for the outage probability as a function of voice activity, power control, and antenna diversity are provided for mobile-to-base transmission. These expressions are used to evaluate the system capacity (users/MHz/cell) based on simulating mobile locations within 37 hexagonal cells. The sensitivity to power control error, voice activity factor, and soft capacity of the system is investigated     

The exergy fields in transport processes: Their calculation and use

This paper is a brief review of the method for analyzing the space and time dependent exergy and irreversibility fields in processes. It presents the basic equations, the method for their use, major literature sources, and three examples from the authors' work: flow desiccation, combustion of oil droplets, and combustion of pulverized coal. Conclusions from this Second Law analysis are used to attempt process improvement suggestions.     

Free convection performance of circular cavities having two active curved vertical sides and two inactive curved horizontal sides

A detailed review of the archival reveals that the heat transfer and fluid flow characteristics of circular cavities have not been investigated so far and of course their physical features are not understood. A prominent application of these cavities arises in the miniaturized packaging of electronic components that are subject to strict constraints. This paper addresses primarily steady-state laminar natural convection of air in a circular cavity of diameter H inscribed in a square cavity of side H where the corresponding sides are in contact at four points. A third cavity, an arc–square cavity whose shape lies between the square and circular cavity shapes is included in the analysis. The finite volume method is used to perform the numerical simulations. The methodology takes into account the second-order-accurate QUICK scheme for the discretization of the convective term, whereas the pressure–velocity coupling is handled with the SIMPLE scheme. Since the air is not assumed a Boussinesq gas, it was decided to take all thermophysical properties as temperature-dependent. In the end, it has been demonstrated that the circular cavity possesses a superior balance between heat transfer enhancement and size in cross-section area in comparison with the standard square cavity. The side of the square cavity is similar to the diameter of the circular cavity.