Vacuum metrology and its impact on research and industry

To mark our anniversary, we are presenting articles that have been particularly appreciated by readers of our online edition once again in print. Here: By accurate vacuum measurement, it is possible to control processes in industry, to ensure the necessary environmental conditions for many experiments in science and research and to support the commercial relationship between manufacturers and users of vacuum equipment. The main task of vacuum metrology, the science of vacuum measurement, is to provide traceability of vacuum measurements to the SI. In recent years, also the characterization of vacuum by partial pressure analysis and outgassing rate measurement, and the dynamics of vacuum measurement became an issue for vacuum metrology.     

On Multicarrier Detection and Coherent CDMA Mobile Receiver Radio Systems with Joint Antenna Diversity

The combination of code division multiple access(CDMA) and multicarrier (MC) transmission techniques,termed MC-CDMA, is considered a promising alternative toconventional DS (direct sequence)-CDMA. For this reason, recent research activities haveconcentrated on the application of MC-CDMA to mobileradio systems. In this paper an MC-CDMA concept which iswell suited for mobile radio applications is described. The described MC-CDMA concept overcomesdisadvantages of previously proposed concepts. InMC-CDMA mobile radio systems, signal reception isimpaired by time-varying multipath propagation. Theimpairments can be reduced by applying diversitytechniques. Coherent receiver antenna diversity (CRAD)is especially attractive because only the signalprocessing at the receivers must be modified. In thiscommunication, the application of CRAD in combination withjoint detection (JD) techniques to the more criticaluplink of MC-CDMA mobile radio systems is investigated.It is explained that the deployment of JD techniques for CRAD is an effective countermeasure againstthe influence of the mobile radio channel on the systemperformance. Four JD techniques for CRAD which areapplicable to MC-CDMA are presented. Their performances are studied in bad urban, typical urban, andtypical macrocellular environments. It is shown thatMC-CDMA allows a favorable performance compared to otherCDMA concepts.     

Microvascular Experimentation in the Chick Chorioallantoic Membrane as a Model for Screening Angiogenic Agents including from Gene-Modified Cells

The chick chorioallantoic membrane (CAM) assay model of angiogenesis has been highlighted as a relatively quick, low cost and effective model for the study of pro-angiogenic and anti-angiogenic factors. The chick CAM is a highly vascularised extraembryonic membrane which functions for gas exchange, nutrient exchange and waste removal for the growing chick embryo. It is beneficial as it can function as a treatment screening tool, which bridges the gap between cell based in vitro studies and in vivo animal experimentation. In this review, we explore the benefits and drawbacks of the CAM assay to study microcirculation, by the investigation of each distinct stage of the CAM assay procedure, including cultivation techniques, treatment applications and methods of determining an angiogenic response using this assay. We detail the angiogenic effect of treatments, including drugs, metabolites, genes and cells used in conjunction with the CAM assay, while also highlighting the testing of genetically modified cells. We also present a detailed exploration of the advantages and limitations of different CAM analysis techniques, including visual assessment, histological and molecular analysis along with vascular casting methods and live blood flow observations.     

Large-scale parallel arrays of silicon nanowires via block copolymer directed self-assembly

Extending the resolution and spatial proximity of lithographic patterning below critical dimensions of 20 nm remains a key challenge with very-large-scale integration, especially if the persistent scaling of silicon electronic devices is sustained. One approach, which relies upon the directed self-assembly of block copolymers by chemical-epitaxy, is capable of achieving high density 1?:?1 patterning with critical dimensions approaching 5 nm. Herein, we outline an integration-favourable strategy for fabricating high areal density arrays of aligned silicon nanowires by directed self-assembly of a PS-b-PMMA block copolymer nanopatterns with a L(0) (pitch) of 42 nm, on chemically pre-patterned surfaces. Parallel arrays (5 × 10(6) wires per cm) of uni-directional and isolated silicon nanowires on insulator substrates with critical dimension ranging from 15 to 19 nm were fabricated by using precision plasma etch processes; with each stage monitored by electron microscopy. This step-by-step approach provides detailed information on interfacial oxide formation at the device silicon layer, the polystyrene profile during plasma etching, final critical dimension uniformity and line edge roughness variation nanowire during processing. The resulting silicon-nanowire array devices exhibit Schottky-type behaviour and a clear field-effect. The measured values for resistivity and specific contact resistance were ((2.6 ± 1.2) × 10(5)Ωcm) and ((240 ± 80) Ωcm(2)) respectively. These values are typical for intrinsic (un-doped) silicon when contacted by high work function metal albeit counterintuitive as the resistivity of the starting wafer (～10 Ωcm) is 4 orders of magnitude lower. In essence, the nanowires are so small and consist of so few atoms, that statistically, at the original doping level each nanowire contains less than a single dopant atom and consequently exhibits the electrical behaviour of the un-doped host material. Moreover this indicates that the processing successfully avoided unintentional doping. Therefore our approach permits tuning of the device steps to contact the nanowires functionality through careful selection of the initial bulk starting material and/or by means of post processing steps e.g. thermal annealing of metal contacts to produce high performance devices. We envision that such a controllable process, combined with the precision patterning of the aligned block copolymer nanopatterns, could prolong the scaling of nanoelectronics and potentially enable the fabrication of dense, parallel arrays of multi-gate field effect transistors.     

Polymerization of cyclic monomers. VII. Synthesis and radical polymerization of 1,3‐bis[(1‐alkoxycarbonyl‐2‐vinylcyclopropane‐1‐yl)carboxy]benzenes

1,3‐Bis[(1‐alkoxycarbonyl‐2‐vinylcyclopropane‐1‐yl)carboxy]benzenes 1 [RO: CH₃O (a), C₂H₅O (b)] were synthesized by the esterification of the corresponding 1‐alkoxycarbonyl‐2‐vinylcyclopropane‐1‐carboxylic acids with resorcinol. The structure of the new vinylcyclopropanes was confirmed by elemental analysis and infrared (IR), ¹H nuclear magnetic resonance (¹H‐NMR), and ¹³C nuclear magnetic resonance (¹³C‐NMR) spectroscopy. The radical polymerization of difunctional 2‐vinyl‐cyclopropanes in bulk with 2,2′‐azoisobutyronitrile (AIBN) results in hard, transparent, crosslinked polymers. During the bulk polymerization of the crystalline bis[(1‐methoxycarbonyl‐2‐vinylcyclopropane‐1‐yl)carboxy]benzene 1a, an expansion in volume of about 1% took place. The radical solution polymerization of 1a resulted in a soluble polymer with pendant 2‐vinylcyclopropane groups. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1775–1782, 1999     

Thermoplastic olefin/clay nanocomposites: Morphology and mechanical properties

Thermoplastic olefin (TPO)/clay nanocomposites were made with clay loadings of 0.6–6.7 wt %. The morphology of these TPO/clay nanocomposites was investigated with atomic force microscopy, transmission electron microscopy (TEM), and X‐ray diffraction. The ethylene–propylene rubber (EPR) particle morphology in the TPO underwent progressive particle breakup and decreased in particle size as the clay loading increased from 0.6 to 5.6 wt %. TEM micrographs showed that the clay platelets preferentially segregated to the rubber–particle interface. The breakup of the EPR particles was suspected to be due to the increasing melt viscosity observed as the clay loading increased or to the accompanying chemical modifiers of the clay, acting as interfacial agents and reducing the interfacial tension with a concomitant reduction in the particle size. The flexural modulus of the injection moldings increased monotonically as the clay loading increased. The unnotched (Izod) impact strength was substantially increased or maintained, whereas the notched (Izod) impact strength decreased modestly as the clay loading increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 928–936, 2004     

Anisotropy Effects in the Shape-Memory Performance of Polymer Foams

Isotropic and anisotropic shape-memory polymer foams are prepared by supercritical carbon dioxide foaming from a multiblock copolymer (PDLCL) consisting of poly(ω-pentadecalactone) and poly(ε-caprolactone) segments. Analysis by micro-computed tomography reveals for the anisotropic PDLCL foam cells a high shape anisotropy ratio of R = 1.72 ± 0.62 with a corresponding Young's compression moduli ratio between longitudinal and transversal direction of 4.3. The experimental compression data in the linear elastic range can be well described by the anisotropic open foam model of Gibson and Ashby. A micro-morphological analysis for single pores using scanning electron microscopy images permits the correlation between the macroscopic stress-compression behavior and microscale structural changes.