Polyethers with phosphate pendant groups by monomer activated anionic ring opening polymerization: Syntheses,characterization and their lithium-ion conductivities

This paper describes the preparations and lithium-ion conductivities of various solid polymer electrolytes for potential use in high-energy density lithium-ion batteries. The ring opening polymerization of epoxides (M1–M6), catalyzed by Zn(II), Cu(II) and Cd(II) complexes in the presence of tetrabutylammonium bromide (TBAB), yielded polyethers (P1–P6) in which phosphates were attached as pendant groups. A reaction condition where Zn(II) catalyst used slightly excess to TBAB increased the polymerization rate remarkably and yielded the polyethers with higher molar masses in a short time. These polymerizations proceeded following a “monomer activated anionic ring opening polymerization” mechanism. These living like polymerizations also progressed according to “formation of polymer chain per initiator” model. The solid-state lithium-ion conductivities of these polymers were examined using lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). The conductivity of one of the solid polymer electrolytes with 40 wt% of LiTFSI was 5.2 × 10⁻⁵ S cm⁻¹ at room temperature and 2.9 × 10⁻⁴ S cm⁻¹ at 80 °C.     

Effect of CoFe2O4 mole percentage on multiferroic and magnetoelectric properties of Na0.5Bi0.5TiO3/CoFe2O4 particulate composites

Na_0.5Bi_0.5TiO₃ (NBT), CoFe₂O₄ (CFO) as well as particulate composites containing different mole percentages of NBT and CFO were synthesized by the solid-state sintering route and characterized for their ferroelectric and ferrimagnetic hysteresis loops, magnetostriction and magnetoelectric (ME) output. The mole% of CFO was found to influence the ferroelectric and ferrimagnetic hysteresis loops as well as magnetostriction and piezomagnetic coefficients which in turn had a significant effect on the magnetoelectric voltage coefficient. The highest magnetoelectric voltage coefficient (α) of 0.5 mV/cm/Oe was recorded in (65) NBT–(35) CFO composite.     

An electrostatic powder spray process for manufacturing thermoplastic composites

Manufacture of thermoplastic composites is expensive because of the difficulty of impregnating the resin into the fibers. Powder processing shows great promise as an impregnation technique for cost-effective manufacturing. This paper discusses an electrostatic powder spray impregnation technique that uses glass fibers. A geodesic fiber spreader is used to spread the fibers locally in the region of maximum powder deposition. A negative corona electrostatic spray gun is employed to charge and direct the powder for coating both sides of the spread fiber tow. The process has been used to impregnate glass fibers with poly(aryl ether ketone ketone) powder. The effect of the powder mass flow, corona voltage, and fiber tow velocity on powder deposition has been investigated. Particle image velocimetry is utilized to determine particle velocities. Compression molded panels have been produced and tested in three point bending.     

Multiple Abiotic Stresses Applied Simultaneously Elicit Distinct Responses in Two Contrasting Rice Cultivars

Rice crops are often subject to multiple abiotic stresses simultaneously in both natural and cultivated environments, resulting in yield reductions beyond those expected from single stress. We report physiological changes after a 4 day exposure to combined drought, salt and extreme temperature treatments, following a 2 day salinity pre-treatment in two rice genotypes—Nipponbare (a paddy rice) and IAC1131 (an upland landrace). Stomata closed after two days of combined stresses, causing intercellular CO2 concentrations and assimilation rates to diminish rapidly. Abscisic acid (ABA) levels increased at least five-fold but did not differ significantly between the genotypes. Tandem Mass Tag isotopic labelling quantitative proteomics revealed 6215 reproducibly identified proteins in mature leaves across the two genotypes and three time points (0, 2 and 4 days of stress). Of these, 987 were differentially expressed due to stress (cf. control plants), including 41 proteins that changed significantly in abundance in all stressed plants. Heat shock proteins, late embryogenesis abundant proteins and photosynthesis-related proteins were consistently responsive to stress in both Nipponbare and IAC1131. Remarkably, even after 2 days of stress there were almost six times fewer proteins differentially expressed in IAC1131 than Nipponbare. This contrast in the translational response to multiple stresses is consistent with the known tolerance of IAC1131 to dryland conditions.     

Synthesis,structural and luminescence properties of near white light emitting Dy-doped Y2CaZnO5 nanophosphor for solid state lighting

Novel near white light emitting Y₂CaZnO₅ (YCZ) nanocrystalline powders doped with Dy³⁺ ions were synthesized via the citrate gel combustion method. The structure of the compound is found to be triclinic with a particle size in the range of 20–30 nm. Luminescence properties have been characterized using photoluminescence (PL), excitation spectra and decay time measurements. The PL spectra have shown a broad blue band due to ⁴F_9/2→⁶H_15/2 transition and sharp yellow band corresponding to ⁴F_9/2→⁶H_13/2 transition of Dy³⁺ ions. From the concentration dependent PL studies, the optimum concentration of Dy³⁺ ions in YCZ is found to be 1.0 mol%, where intense near white light emission was observed. The Dy³⁺:YCZ nanophosphor has shown relatively better white color properties than the reported Dy³⁺:Y₂O₃ nanophosphor. The yellow to blue intensity ratios, CIE chromaticity coordinates and correlated color temperature studies have shown the possibility of using this compound for white light emission.     

Review: Investigation of Partially Pre-mixed Charge Ignitions (PPCI) Engine Mode

This paper embraces the key points of unpolluted internally combusted engine emissions. Core objective is focused on the recent effort to improve compression ignition(CI) and spark ignition(SI) engine to have fuel-efficient and minimized pollutant emissions. There are many advanced internal combustion engines to overcome the challenges of conventional compression ignition engines of the high level of particulate matter(PM) and oxides of nitrogen emission. One of the latest options on which many ...     

A systematic approach to preliminary polymer process development: modeling and design

A general and complete methodology is presented to facilitate systematic modeling and design of polymer processes during the early development period. To capture and handle the subjective type of uncertainty, embedded in the preliminary process development, fuzzy theories are used as a basis to model and design the process in the presence of ambiguity and vagueness. Physical membership functions are developed for mapping the relation between process variables and the associated fuzzy uncertainties. Based on the qualitative results generated using our previously proposed “linguistic based preliminary design method,” the process modeling can be followed even in the absence of any process governing equations. The modeling is carried out by establishing an appropriate fuzzy reasoning system which provides a specific functional mapping that relates input process variables to one (or more than one) output performance parameter(s). A reduced yet feasible domain is generated by our qualitative design scheme to constrain the process variables. Now, any optimization routine can then be employed to search for a proper process design. We demonstrate the effectiveness of the proposed methodology by its application to a typical compression molding process.     

Targeting Endothelial Connexin37 Reduces Angiogenesis and Decreases Tumor Growth

Connexin37 (Cx37) and Cx40 form intercellular channels between endothelial cells (EC), which contribute to the regulation of the functions of vessels. We previously documented the participation of both Cx in developmental angiogenesis and have further shown that loss of Cx40 decreases the growth of different tumors. Here, we report that loss of Cx37 reduces (1) the in vitro proliferation of primary human EC; (2) the vascularization of subcutaneously implanted matrigel plugs in Cx37−/− mice or in WT using matrigel plugs supplemented with a peptide targeting Cx37 channels; (3) tumor angiogenesis; and (4) the growth of TC-1 and B16 tumors, resulting in a longer mice survival. We further document that Cx37 and Cx40 function in a collaborative manner to promote tumor growth, inasmuch as the injection of a peptide targeting Cx40 into Cx37−/− mice decreased the growth of TC-1 tumors to a larger extent than after loss of Cx37. This loss did not alter vessel perfusion, mural cells coverage and tumor hypoxia compared to tumors grown in WT mice. The data show that Cx37 is relevant for the control of EC proliferation and growth in different tumor models, suggesting that it may be a target, alone or in combination with Cx40, in the development of anti-tumoral treatments.     

Modeling and analysis of rapid catalyst aging cycles

The primary mode of deactivation of automotive emission control catalysts is thermal aging, and it is well-known that high-temperature lean aging conditions are particularly detrimental. Since evaluating the long-term durability of automotive catalysts is costly and time-consuming, rapid catalyst aging cycles have been developed to mimic (in a reduced time) the catalyst deactivation under real-world driving conditions. One of the commonly used rapid catalyst aging tests is an exothermal aging cycle, which involves a combination of fuel-rich engine operation and supplemental air injection to generate high-temperature lean conditions within the catalyst bed. In this work, we use the previously developed transient three-way catalyst model to investigate the time evolution of the axial temperature profiles and exhaust air–fuel ratio (A/F) along the catalyst bed during the course of the exothermal rapid aging cycles. We find that the thermal front propagates downstream through the catalyst bed relatively slowly (compared to the concentration front) and this can limit the location within the catalyst bed and duration for high-temperature lean exposure. We also investigate how variations of some of the key system design and operating parameters can affect the extent and duration of high-temperature lean exposure. Finally, a simple analytical expression is developed which allows one to estimate the time it takes for the thermal front to travel through the catalyst bed. This time can be compared with the period of the lean A/F operation during the aging cycle to determine the location and duration of high-temperature lean exposure.