A New Temperature Compensating Method for Logarithmic Amplifier

A new method of temperature compensation for a dc logarithmic amplifier is presented. By this method temperature effect on both parallel shift and slope variance of log I vs. VBE curve can be compensated easily by using only one compensating resistor of copper wire wound type. (hereafter called parallel and slope compensations.) An absolute compensation condition can be determined for each type of logarithmic transistors, like silicon NPN, germanium PNP irrespective of current measuring range. The temperature dependence of the logarithmic amplifier is reduced to 0.01 decade for the temperature range from 0°C to 50°C and the current range from 10-11 to 10-3A.     

Aging and thermal stability of Mg/SiC and Mg/Y2O3 reflection multilayers in the 25-35 nm region

Reflection measurements in the 25-35 nm region were made for Mg/SiC and Mg/Y2O3 multilayers kept in a low-humidity atmosphere for 4 or 5 years. Aged Mg/SiC multilayers keep their reflectances, and the reflectance value at 31.2 nm is 0.44 at 10 degrees of the normal angle of incidence. Aged Mg/Y2O3 multilayers change reflectance as top layer materials, and the best value at 30.1 nm is 0.40 at 10 degrees. Reflection measurements are also made for Mg-based multilayers that are annealed from room temperature to 400 degrees C at 50 degrees C intervals. Both multilayers keep their reflectance at annealing temperatures of 200 degrees C. These results suggest that both Mg-based multilayers can be applied to practical optics.     

Role of mitochondria in the switch mechanism of the cell death mode from apoptosis to necrosis--studies on rho0 cells

Detailed mechanisms of the switch of the cell death mode from apoptosis to necrosis remain to be solved, although the intracellular level of ATP and that of free radicals have been postulated to be the major factors involved in the mechanisms. In the present study menadione (MEN)-induced cell injury processes were studied using rho0 cells derived from human osteosarcoma 143B cells and parental rho+ cells co-treated with inhibitors of electron transfer chain of mitochondria or oligomycin, an inhibitor of ATP synthesis. Treatment of rho+ cells with 100 microM MEN induced apoptosis, which reached the maximum at 6 h, and was followed by an abrupt decrease thereafter, while necrotic cells (NC) increased continuously when they were judged by Annexin V and PI double staining. On the other hand, MEN induced apoptotic and necrotic changes much faster in rho0 cells compared to rho+ cells. The frequency to find apoptotic cells (AP) in the former cells was distinctly smaller than that to find NC judged by Annexin V and PI double staining. Electron microscopically, a major population of rho0 cells treated with MEN for 6 h consisted of intermediate cells, and a small number of AP co-existed. At 9 h of the treatment intermediate cells were exclusively seen, and AP were hardly detected. When parental rho+ cells were treated with MEN in the presence of oligomycin or oligomycin plus antimycin A both apoptotic and necrotic changes of the cells were distinctly accelerated. The intracellular level of superoxide in rho0 cells continuously increased after the MEN treatment, whereas that of ATP remained distinctly low before and after the MEN treatment compared to that in rho+ cells. These data suggest that the intracellular level of superoxide may be a key factor controlling the switch from apoptosis to necrosis.     

Quantitative detection system for maize sample containing combined-trait genetically modified maize

Various countries have established regulations that stipulate the labeling of agricultural commodities, feed, and food products that contain or are made from genetically modified (GM) material or that contain adventitious GM material in amounts that exceed certain threshold levels. While regulations in some countries refer to GM material on a weight per weight (w/w) percentage, the currently applied detection methods do not directly measure the w/w percentage of the GM material. Depending on the particular method and the sample matrix it is applied to, the conversion of analytical results to a w/w percentage is challenging or not possible. The first rapid PCR system for GM maize detection on a single kernel basis has been developed. The equipment for the grinding of individual kernels and a silica membrane-based 96-well DNA extraction kit were both significantly revised and optimized for this particular purpose, respectively. We developed a multiplex real-time PCR method for the rapid quantification of GM DNA sequences in the obtained DNA solutions. In addition, a multiplex qualitative PCR detection method allows for the simultaneous detection of different GM maize traits in each kernel and thereby for identification of individual kernels that contain a combination of two or more GM traits. Especially for grain samples that potentially contain combined-trait GM maize kernels, the proposed methods can deliver informative results in a rapid, precise, and reliable manner.     

Nanoporous reactor with tunable selectivity on alkylation of ethylbenzene

As nanoporous reactor, mesoporous silicates containing aluminum acidic site with n(Si)/n(Al) ratio up to 7 (AISBA-15) were prepared through a simple one-pot synthesis, which was recently developed by parts of us. The obtained materials were satisfactorily characterized by XRD and nitrogen adsorption/desorption and have regularly arranged hexagonal structures with pore diameters in the 9.6-11.8-nm range. The density and strength of the acid sites were determined using temperature-programmed desorption (TPD) of pyridine and controlled distribution between weak, moderate, and strong acid sites was demonstrated. The alkylation of ethylbenzene in a fixed-bed flow-type reactor using the AISBA-15 nanoporous reactor was carried out under various conditions such as temperature, feed ratio, flow rate, and time on stream. Interestingly, perfect regioselectivity between the m-isomer and the o-/p-isomers of diethylbenzene was achieved, where 100% selectivity of the m-isomer or the o-/p-isomers can be obtained by simply tuning the reaction temperature by using AISBA-15 catalyst with appropriate aluminum content.     

Uniformity of flow from sheeting dies

A numerical method for analyzing the uniformity of flow from sheeting dies is presented. The method assumes that the flow is isothermal and that the material is a power law fluid. A uniformity index is defined and methods are presented which enable die dimensions to be established which will result in a specified uniformity at particular flow rates and pressure drops. The analysis shows that the flow index “n” of the power law is the key parameter determining the uniformity of flow from a sheeting die.     

Analysis of air pollution and prevalence rate of allergic diseases among elementary school children in Kawaguchi and Hatogaya city

Kawaguchi and Hatogaya City are located on the northern edge of Tokyo. We analysed between air pollution and prevalence rate of allergic diseases among elementary school children in this area. A prevalence rate of allergic diseases in 1996 May and June was as follows; bronchial asthma 13.5%, atopic dermatitis 24.5%, allergic rhinitis and/or conjunctivitis 22.8%, urticaria 12.4%, food allergy 7.8% and drug allergy 2.2%, respectively. Air pollution of this area was analysed to check the levels of nitrogen dioxide (NO2), sulfur dioxide (SO2) and suspended particulate matters (SPM). NO2 pollution was relatively high in urban area, and SPM pollution was especially high around the highways. SO2 pollution was lower than the environmental standard. No relationship was found between the prevalence rate of bronchial asthma, atopic dermatitis, allergic rhinitis and/or conjunctivitis and air pollution, but it was found that these diseases are slightly related to population density (p < 0.1, p < 0.01, p < 0.1, respectively).     

Inhibition of hyphal growth of azole-resistant strains of Candida albicans by triazole antifungal agents in the presence of lactoferrin-related compounds

The effects of bovine lactoferrin (LF) or the LF-derived antimicrobial peptide lactoferricin B (LFcin B) on the growth of Candida albicans hyphae, including those of three azole-resistant strains, were investigated by a crystal violet staining method. The hyphae of two highly azole-resistant strains were more susceptible to inhibition by LF or LFcin B than the azole-susceptible strains tested. One moderately azole-resistant strain was defective in the formation of hyphae and showed a susceptibility to LF greater than that of the susceptible strains but a susceptibility to LFcin B similar to that of the susceptible strains. The highly azole-resistant strain TIMM3317 showed trailing growth in the presence of fluconazole or itraconazole, while the extent of growth was reduced by the addition of LF or LFcin B at a sub-MIC. Thus, the addition of LF or LFcin B at a sub-MIC resulted in a substantial decrease in the MICs of fluconazole and itraconazole for two highly azole-resistant strains; e.g., the MIC of fluconazole for TIMM3317 was shifted from > 256 to 0.25 micrograms/ml by LF, but the MICs were not decreased for the susceptible strains. The combination effects observed with triazoles and LF-related compounds in the case of the two highly azole-resistant strains were confirmed to be synergistic by the fractional inhibitory concentration index. These results demonstrate that for some azole-resistant C. albicans strains, LF-related compounds combined with triazoles can inhibit the growth of hyphae, an important form of this organism in pathogenesis.     

Improved efficiency of polymer light-emitting diodes by inserting a hole transport layer formed without thermal treatment above glass transition temperature

We have demonstrated a significant improvement in the performance of polymer light-emitting diodes (PLEDs) by inserting the fluorene-triatylamine copolymer as hole transport layer (HTL) without a thermal treatment above the glass transition temperature (T_g). A thin HTL insolubilized by a thermal treatment above T_g is often inserted as an interlayer between an anode buffer layer and a light-emitting polymer (LEP) in PLEDs fabricated by using a conventional solution process. The evaporative spray deposition using ultradiluted solution (ESDUS) method has enabled fabricating polymer bilayer structure without an insolublizing procedure. The bilayer PLEDs fabricated by ESDUS without the thermal treatment showed significantly higher and more stable external quantum efficiency than PLEDs having the conventional interlayer. Thermal treatment above T_g of the copolymer would induce degradation of its hole injection property. Furthermore, ESDUS bilayer devices showed much higher power efficiency than interlayer devices when calcium was used for cathode. The improvements would be caused by the enhancement of hole injection and the effective electron blocking at the copolymer/LEP interface in the ESDUS bilayer devices.