EAAM: Energy-aware application management strategy for FPGA-based IoT-Cloud environments

The Journal of Supercomputing - An efficient integration of Internet of Things (IoT) and cloud computing techniques accelerates the evolution of next-generation smart environments (e.g., smart...     

A standard deviation based firefly algorithm for multi-objective optimization of WEDM process during machining of Indian RAFM steel

Non-conventional machining processes always suffer due to their low productivity and high cost. However, a suitable machining process should improve its productivity without compromising product quality. This implies the necessity to use efficient multi-objective optimization algorithm in non-conventional machining processes. In this present paper, an effective standard deviation based multi-objective fire-fly algorithm is proposed to predict various process parameters for maximum productivity (without affecting product quality) during WEDM of Indian RAFM steel. The process parameters of WEDM considered for this study are: pulse current (I), pulse-on time (T _on), pulse-off time (T _off) and wire tension (WT).While, cutting speed (CS) and surface roughness (SR) were considered as machining performance parameters. Mathematical models relating the process and response parameters had been developed by linear regression analysis and standard deviation method was used to convert this multi objective into single objective by unifying the responses. The model was then implemented in firefly algorithm in order to optimize the process parameters. The computational results depict that the proposed method is well capable of giving optimal results in WEDM process and is fairly superior to the two most popular evolutionary algorithms (particle swarm optimization algorithm and differential evolution algorithm) available in the literature.

     

信号调制系统实现角位移测量（英文）

采用基于定时器LM555的非稳态多谐振荡器和通用频数转换设计了一种变面积式电容传感器信号调制系统用于角位移测量。变面积式电容器连接在基于定时器的非稳态电路内,其角位移的变化引起电容的变化,进而引起定时器电路输出时间周期的变化。定时器电路输出波形的时间周期与电容呈线性关系,因而与角位移也是线性关系。定时器输出经通用频数转换器进一步处理后可用于测量。实验结果显示,时间周期与角位移在0-180°范围内呈线性关系,将不确定度与平均时间周期相关联,即为平均标准差,亦称为标准误差,其值为±0.023μs。该测量系统使用简单,可用于电子和工业仪器中。     

On the mechanisms of secondary flows in a gas vortex unit

The hydrodynamics of secondary flow phenomena in a disc‐shaped gas vortex unit (GVU) is investigated using experimentally validated numerical simulations. The simulation using ANSYS FLUENT^® v.14a reveals the development of a backflow region along the core of the central gas exhaust, and of a counterflow multivortex region in the bulk of the disc part of the unit. Under the tested conditions, the GVU flow is found to be highly spiraling in nature. Secondary flow phenomena develop as swirl becomes stronger. The backflow region develops first via the swirl‐decay mechanism in the exhaust line. Near‐wall jet formation in the boundary layers near the GVU end‐walls eventually results in flow reversal in the bulk of the unit. When the jets grow stronger the counterflow becomes multivortex. The simulation results are validated with experimental data obtained from Stereoscopic Particle Image Velocimetry and surface oil visualization measurements. © 2018 The Authors AIChE Journal published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers AIChE J, 64: 1859–1873, 2018     

Estimating weak ratiometric signals in imaging data. II. Meta-analysis with multiple, dual-channel datasets

Ratiometric fluorescent indicators are used for making quantitative measurements of a variety of physiological variables. Their utility is often limited by noise. This is the second in a series of papers describing statistical methods for denoising ratiometric data with the aim of obtaining improved quantitative estimates of variables of interest. Here, we outline a statistical optimization method that is designed for the analysis of ratiometric imaging data in which multiple measurements have been taken of systems responding to the same stimulation protocol. This method takes advantage of correlated information across multiple datasets for objectively detecting and estimating ratiometric signals. We demonstrate our method by showing results of its application on multiple, ratiometric calcium imaging experiments.     

Structure–property relationship of electron‐beam‐modified EPDM rubber

Electron‐beam‐initiated grafting of trimethylolpropane triacrylate (TMPTA) onto the bulk ethylene propylene diene monomer (EPDM) was carried out with varying concentrations of TMPTA at a constant irradiation dose of 100 kGy and over a wide range of irradiation doses (0–500 kGy) at a fixed concentration (10%) of TMPTA. The rubber was also modified in the bulk by tripropylene glycol diacrylate (TPGDA, 10%) and tetramethylol methane tetraacrylate (TMMT, 10%) at an irradiation dose of 100 kGy. The modified rubbers were characterized by IR spectroscopy, crosslinking density measurements, and mechanical, dynamic mechanical, and electrical properties. The IR studies indicated increased peak absorbances at 1730, 1260, and 1019 cm⁻¹ due to increased 〉CO and C O C concentrations up to certain levels of TMPTA and irradiation dose. These are accompanied by an increase in the crosslinking density. The tensile strength of the samples increases gradually with increasing both the concentration of the monomer and radiation dose up to a certain level. The values of the modulus also increase at the expense of the elongation at break. An increase in the number of double bonds from two in the case of the diacrylate to four in the case of the tetraacrylate also brings about an increase in the tensile strength and moduli values. The elongation at break, however, decreases. The DMTA measurements indicate changes in the glass transition temperature, T_g, and tan δ_max on modification. The T_g shifts to a higher temperature with a simultaneous lowering of the tan δ_max values as the TMPTA level is increased. A similar trend is observed when the irradiation dose is increased and the nature of the monomer changes from di‐ to tetraacrylate. The dielectric loss tangent registers an increase on modification by irradiation of TMPTA while the permittivity is decreased. All the results could be explained on the basis of the structural modification and crosslinking density. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 323–337, 2000     

Effect of Cryogenic Pre-Treatment on Breakage Characteristics of Rocks

Improvement of energy efficiency in comminution of rocks using various pretreatment methods is being explored worldwide. This paper presents experimental data on breakage characteristics of granite and sandstone using cryogenic pre-treatment. The samples were treated with varying duration of immersion in liquid nitrogen. Combined pretreatment using oven heating followed by quenching in liquid nitrogen were also explored. The results indicate that using cryogenic pretreatment uniaxial tensile strength of granite can be decreased by more than 40% while in uniaxial compressive strength about 28% reduction is possible. For sandstone as much as 33% reduction in uniaxial compressive strength was observed.

     

Factorial Design Approach to Investigate the Effects of Groundwater Cooccurring Solutes on Arsenic Removal by Electrocoagulation

Effects of groundwater cooccurring solutes such as phosphate (PO4), silicate (SiO3), bicarbonate (HCO3), calcium (Ca), and iron (Fe) on arsenic removal were investigated in this study. Investigation by two-level full-factorial designed experiments revealed that PO4 and SiO3 have negative effect on arsenic removal, whereas HCO3 has negligible positive effect. The effects of Ca and Fe present in groundwater have positive effect on arsenic removal by electrocoagulation (EC). Hypothesis testing at 5% significance level suggests that alkalinity (HCO3) is not an important parameter in arsenic removal by EC in naturally occurring pH range of water.     

Prediction of Arsenic Removal by Electrocoagulation: Model Development by Factorial Design

Model was developed by two-level five-factor full-factorial designed-experiment to predict arsenic removal from contaminated water by electrocoagulation. Five factors, namely arsenic concentration (As), solution volume (V); current (I), electrode area (A), and current processing time (t) were investigated. Among the factors, arsenic concentration (As) and volume (V) have negative effect, and area (A), time (t), and current (I) have positive effect on arsenic removal. Within the studied levels of the factors, variance analysis at 5% significance level indicated that electrode area is not significant in arsenic removal by electrocoagulation. The model predicted reasonably good arsenic removal (error<2%) from low (0.288 mg/L) and high (0.882 mg/L) initial arsenic concentrations in presence of naturally cooccurring solutes in the groundwater. For the range of operating variables studied, optimum removal of arsenic (98.56%) is obtained at higher arsenic concentration (1.18 mg/L), lower volume (1 L), higher current (3 A), and higher current processing time (120 s).