Fully Coupled 3-D Conjugate Heat Transfer Algorithm for Borehole Heat Exchanger Performance Prediction

Quantitative three-dimensional prediction of the thermal performance of a vertical borehole heat exchanger (BHE) in a ground-source heat pump installation is sought. As BHE installation exhibits exceptionally disparate characteristic length scales, an alternative formation-fluid-thermal fully coupled algorithm is derived to quickly predict the 3-D temperature distributions. The time scale of the steady prediction is of order minutes. This simulation capability can be readily coupled to long-time (order months) unsteady simulation of an entire wellbore field. Algorithm prediction is validated by comparison with data from an instrumented commercial installation for a unique BHE conduit design, followed by illustrative design optimization or variation assessments.     

Two-phase cooling characteristics of a saturated free falling circular jet of HFE7100 on a heated disk: Effect of jet length

Direct jet impingement boiling heat transfer operating at low flow rates is of great interest for the localized moderate heat fluxes from the targets with delicate mechanical structure, where the aggressive techniques such as high-speed jets are not suitable. Boiling heat transfer from an upward facing disk targeted by a falling jet was studied experimentally at different volumetric flow rates and various jet lengths. The working fluid was chosen to be the dielectric liquid HFE7100 and the heated spot was an 8-mm diameter disk. Using previous CHF correlations in their original form, valid at very low volumetric flow rates, results in large disagreements since it was found that variation in the jet length changes the boiling characteristics. It is demonstrated that although the circular hydraulic jump formation within the heater diameter may suppress the heat transfer under certain conditions, moving the jet closer to the target may significantly improve the boiling curves at the critical heat flux (CHF) regime. At low flow rates, the CHF increases as the jet length decreases while for moderate and high flow rates the boiling curves show approximately a universal behavior for different jet lengths. For such low flow rates, the effect of jet length on boiling curves was shown to be related to the variation of the cross section of the falling jet and the formation of hydraulic jump at radial distances smaller than the heater diameter. The current CHF results for different jet lengths are correlated by including the effect of jet length in the previous correlation proposed by Sharan and Lienhard.     

Acoustic emission for detecting deterioration of capacitors under aging

There is continuous pressure on production cost reduction of foil-based capacitors, widely used in domestic appliance. Therefore, investigation of the deterioration mechanisms within capacitors is important to reduce their production costs at maintained reliability. These mechanisms were observed in two capacitors batches of classes Y2 (27 nF) and X2 (470 nF). An acoustic emission signal was observed when the capacitors were polarized by excessive voltage. This signal is induced by partial discharges that can lead to capacitor destruction. Next, the capacitors were aged at elevated temperature and also in presence of excessive polarization. We conclude that the acoustic emission signal can predict deterioration of dielectric insulation resistance in capacitors of class Y2. The observed destruction of capacitor of class X2 is caused mainly by detachment of the sprayed metalized contacts that is induced by overheating during partial discharges sparking.     

Expert system shells in student advising

A student advising expert system has been developed using the EXSYS Professional expert system shell. The motivation of using a commercially-available expert system shell is presented. Examples of IF-THEN-ELSE type of rules are shown. Interrelation of the knowledge base with class offerings, and with the structure of the B.Sc. program in Computer Science is demonstrated. The development process is described in detail. Improvements resulted from testing the system are presented.     

Optimal optical design of thin-film photovoltaic devices

In this paper we report the results of an effort to develop a design tool to optimise any solar cell with thin-film structure. An optical admittance analysis which takes into account the interference effects in the multilayer thin-film system is discussed. This method provides a technique for calculating the optical properties of a thin-film device with a multilayer configuration. It also allows us to explore the nature and magnitude of optical losses in p-i-n type single or multi-junction a-Si : H solar cells, and to optimise the structure of such cells to utilise enhanced interference effects to obtain the maximum possible utilisation of incident solar radiation.     

The influence of porous silicon on junction formation in silicon solar cells

In this work the results of a structural investigation by SEM of porous silicon (PS) before and after diffusion processes are reported. The formation of PS n⁺/p structures were carried out on PS p/p silicon wafers with two methods: from POCl₃ in a conventional furnace and from a phosphorous doped paste in an infrared furnace. Sheet resistance was found to be a strong function of PS structure. Further details on sheet resistance distribution are reported. The electrical contacts in prepared solar cells were obtained by screen printing process, with a Du Ponte photovoltaic silver paste for front contacts and home-prepared silver with 3% aluminium paste for the back ones. Metallization was done in the infrared furnace. Solar cell current–voltage characteristics were measured under an AM 1.5 global spectrum sun simulator. The average results for multi-crystalline silicon solar cells without antireflection coating are: I_sc=720 (mA), V_oc=560 (mV), FF=69%, Eff=10.6% (area 25 cm²).     

The preparation of TiO2–nitrogen doped by calcination of TiO2·xH2O under ammonia atmosphere for visible light photocatalysis

The investigation on incorporating nitrogen group into titanium dioxide in order to obtain powdered visible light-active photocatalysts is presented. The industrial hydrated amorphous titanium dioxide (TiO₂·xH₂O) obtained directly from sulphate technology installation was modified by heat treatment at temperatures of 100–800 °C for 4 h in an ammonia atmosphere. The photocatalysts were characterized by UV–VIS–DR and XRD techniques. The UV–VIS–DR spectra of the modified catalysts exhibited an additional maximum in the VIS region (, ) which may be due to the presence of nitrogen in TiO₂ structure. On the basis of XRD analysis it can be supposed that the presence of nitrogen does not have any influence on the transformation temperature of anatase to rutile. The photocatalytic activity of the modified photocatalysts was determined on the basis of decomposition rate of phenol and azo-dye (Reactive Red 198) under visible light irradiation. The highest rate of phenol degradation was obtained for catalysts calcinated at 700 °C (6.55%), and the highest rate of dye decomposition was found for catalysts calcinated at 500 and 600 °C (ca. 40–45%). The nitrogen doping during calcination under ammonia atmosphere is a very promising way of preparation of photocatalysts which could have a practical application in water treatment system under broader solar light spectrum.     

Aspects of dSpace in contemporary design

Computer dependent design space is illustrated with the recent international competition project for Kowloon Arts Center. The spatial condition of design resulted from the deployment of Euclidian geometry and use of the nonrational, complex surfaces. Another aspect of computer dependent space was rooted in the contemporary work situation where architects located on the three different continents collaborated in distributed mode over the internet. The resulting project confirms the creative potential of the above aspects of the digital space in contemporary design.     

The phenomena of the interaction of Nd3+-glass laser light with 6H13 alloy steel

The variation in the physical and chemical structure of the 6H13 alloy steel irradiated by laser light have been investigated. The phenomena of the capillary waves within the power density range (4.3×10⁹<P<13.8×10⁹) watt/m² have been observed and the hydrodynamic parameters of alloy steel have been determinated. The nature of the laser light interaction with metal is discussed in electronmicroscopy and X-rays analysis terms.     

Effect of molybdenum on the fracture characteristic of high-speed steel quenched matrix

The fractures of three model alloys, imitating by their chemical composition the matrixes of the quenched high-speed steels of various Mo: W relations were analyzed. According to the measurements of the stress intensity factor K_Ic and the differences in the precipitation processes of carbides it was found out that the higher fracture toughness of the matrix of the molybdenum high-speed steels than on the tungsten ones is the results of the differences in the kinetics of precipitation from the martensite matrix of these steels during tempering. After tempering at 250 and 650°C the percentage of the intergranular fracture increases with the increase of the relation of Mo to W in the model alloys of the high-speed steel matrix. This is probably the result of higher precipitation rate of the M₃C carbide (at 250°C) and the MC and M₆C carbides (at 650°C) in the privileged regions along the grain boundaries. The change of the character of the model alloy fractures after tempering at 450°C from the completely transgranular one in the tungsten alloy to the nearly completely intergranular one in the molybdenum alloy indicates that the coherent precipitation processes responsible for the secondary hardness effect in the tungsten matrix begin at a lower temperature than in the molybdenum matrix. After tempering for the maximum secondary hardness the matrix fractures of the high-speed steels reveal a transgranular character regardless the relation of Mo to W. The higher fracture toughness of the Mo matrix can be the result of the start of the coherent precipitation processes at a higher temperature and their intensity which can, respectively, influence the size of these precipitations, their shape and the degree of dispersion. The transgranular character of the fractures of the S 6-5-2 type high-speed steel in the whole range tempering temperatures results from the presence of the undissolved carbides which while cracking in the region of stress concentration can constitute flaws of critical size which form the path of easy cracking through the grains. The transgranular cracking of the matrix of the real high-speed steels does not change the adventageous influence of molybdenum upon their fracture toughness. On the other hand, the carbides, undissolved during austenitizing, whose size distribution in the molybdenum steels from the point of view of cracking mechanics seems to be unsatisfactory, influence significantly the fracture toughness of these steels.