A 2.2 W, 80 MHz superscalar RISC microprocessor

A 28 mW/MHz at 80 MHz structured-custom RISC microprocessor design is described. This 32-b implementation of the PowerPC architecture is fabricated in a 3.3 V, 0.5 μm, 4-level metal CMOS technology, resulting in 1.6 million transistors in a 7.4 mm by 11.5 mm chip size. Dual 8-kilobyte instruction and data caches coupled to a high performance 32/64-b system bus and separate execution units (float, integer, loadstore, and system units) result in peak instruction rates of three instructions per clock cycle. Low-power design techniques are used throughout the entire design, including dynamically powered down execution units. Typical power dissipation is kept under 2.2 W at 80 MHz. Three distinct levels of software-programmable, static, low-power operation-for system power management are offered, resulting in standby power dissipation from 2 mW to 350 mW. CPU to bus clock ratios of 1×, 2×, 3×, and 4× are implemented to allow control of system power while maintaining processor performance. As a result, workstation level performance is packed into a low-power, low-cost design ideal for notebooks and desktop computers     

Change of characteristics of desulfurization and denitrification by combustion flue gas composition and electrode configuration under pulsed corona discharge

Laboratory-scale and parametric experiments of SO₂ and NO_x removal from the simulated combustion gas by pulsed corona discharge have been performed by changing the combustion gas composition and temperature, the electrode configuration of plasma reactor, and the polarity of high-voltage electrode. The following results are obtained: 1) the higher the concentration of H₂O and O₂, the higher the efficiency of desulfurization and denitrification at the same specific input; 2) the pulsed corona discharge with a voltage pulsewidth as short as 200 ns of negative polarity shows the possibility to attain almost 90 percent deSO_x and deNO_x efficiency at the specific discharge input of 20 J/g, which is almost the same as the specific input in the electron-beam process; 3) the deNO_x characteristics show a little temperature dependence in the range of 70 to 130°C, but the deSO_x efficiency increases rapidly in the temperature region below 100°C suggesting the thermochemical dependence of deSO_x reaction; 4) when desulfurization and denitrification proceed, the white dendritic powder deposits on the plasma reactor whose composition is identified to be 49 mol% (NH₄)₂SO₄ and 47 mol% of 2NH₄NO₃ · (NH₄)₂SO₄, and the ratio of SO₂, NO and NH₃ of the deposit is almost equal to that of supplied gas.     

Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

基于媒体用户访问行为偏好模型的代理缓存算法

目前,代理缓存技术广泛应用于改善流媒体传输的服务质量.文章从实际用户日志文件的分析出发,利用发现的用户浏览流媒体对象时的行为分布模型,提出了一种新的视频流媒体缓存算法.仿真结果证明,该算法可以通过记录很少的用户访问信息获取较高的性能表现.     

Neutronic and thermodynamic feasibility of UF6-NpF6 fueled transmutation reactor

Transmutation of neptunium, which is contained in radioactive wastes discharged from nuclear reactors, was investigated as a substitutional method for geologic disposal. We proposed a transmutation reactor fueled with a mixture of gaseous ²³³UF₆ and ²³⁷NpF₆. Neutronic and thermodynamic analysis of the reactor revealed the feasibility of the concept. The reactor has two principal advantages: (1) use of the fuel gas enables on-line reprocessing, (2) ²³⁷Np can be transmuted by a high neutron flux. Our calculation indicated that the transmutation rate of ²³⁷Np was 335 g/year/MW_th, which is much larger than the annual yield of ²³²Np in PWR (6.19 g/year/MW_th).     

Boundary type finite element method for surface wave motion based on trigonometric function interpolation

There are many physical phenomena which can be handled by the Helmholtz equation. The equation explains certain phenomena of wave propagation. This paper presents a new finite element method to analyse surface wave motion. The characteristic point of this method is that the interpolation equation is chosen to satisfy the governing Helmholtz equation using trigonometric functions. This follows that the variational functional to be minimized can be formulated such that the integration is limited to the boundary of the element. The numerical solutions obtained are compared with analytical and experimental solutions. From these comparative studies, it is concluded that the present method provides a useful tool for the analysis of surface wave motion.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Antioxidant activity of anacardic acids

Anacardic acids, 6-pentadec(en)ylsalicylic acids isolated from the cashew Anacardium occidentale L. (Anacardiaceae) nut and apple, were found to possess preventive antioxidant activity while salicylic acid did not show this activity. These anacardic acids prevent generation of superoxide radicals by inhibiting xanthine oxidase (EC 1.1.3.22, Grade IV) without radical-scavenging activity. Notably, the inhibition kinetics of anacardic acids do not follow hyperbolic dependence of enzyme inhibition on inhibitor contents (Michaelis–Menten equation) but follow the Hill equation instead. Anacardic acid (C_15:1) inhibited the soybean lipoxygenase-1 (EC 1.13.11.12, Type 1) catalyzed oxidation of linoleic acid with an IC₅₀ of 6.8 μM. The inhibition is a slow and reversible reaction without residual enzyme activity. The inhibition kinetics indicate that anacardic acid (C_15:1) is a competitive inhibitor and the inhibition constant, K_I, was 2.8 μM. Anacardic acids act as antioxidants in a variety ways, including inhibition of various prooxidant enzymes involved in the production of the reactive oxygen species and chelate divalent metal ions such as Fe²⁺ or Cu²⁺, but do not quench reactive oxygen species. The C₁₅-alkenyl side chain is largely associated with the activity.     

Syntheses and structural properties of four Rb-aluminosilicate zeolites

Four types of Rb-aluminosilicate zeolites were hydrothermally synthesized in pure phase for the first time from Rb-aluminosilicate gels without using any organic structure-directing agent (SDA) under stirring conditions. The crystal structure of each zeolite was refined by Rietveld analysis of the X-ray diffraction (XRD) data. These crystal structures were confirmed to be Rb-mordenite, Rb-merlinoite, a new aluminosilicate zeolite with an ATT framework topology, and Rb-offretite denoted by RMA-1, RMA-2, RMA-3, and RMA-4, respectively. The Si/Al ratio of RMA-1 with an MOR topology varied from 5.3 to 8.0; however, the variation of the Si/Al ratios of the other zeolites was rather small. The crystal system of RMA-2 was tetragonal with space group I4/mmm, where two Rb sites were distributed at the center of an 8-membered ring (MR). On the other hand, two Rb sites in RMA-3 were located at the center of the 8-MR in small two cages. The structure of RMA-4 was identified as the OFF type with a local disorder or defect, which included a small amount of an intergrown ERI phase.