Effect of microstructures on dielectric breakdown strength of sintered reaction-bonded silicon nitride ceramics

Silicon nitride (Si₃N₄) was prepared from silicon by a sintered reaction-bonded silicon nitride method using yttria and magnesia as sintering additives. Post-sintering (PS) of nitrided compacts was carried out at 1850°C under a nitrogen pressure of 1 MPa. Effect of PS time on microstructure and dielectric breakdown strength (DBS) of the prepared Si₃N₄ ceramics was evaluated. The DBS was measured using specimens with four different thicknesses (0.30, 0.20, 0.10, and 0.05 mm) in order to examine the thickness dependence. The porosity of the sintered Si₃N₄ decreased by prolonging the PS time, and the full density could be achieved at the PS time of over 6 h. After full densification, rod-like β-Si₃N₄ grains grew up, and their maximum grain size increased from 45.1 to 154.7 μm by prolonging the PS time from 6 to 48 h. The DBS of the thick Si₃N₄ substrates (0.30 mm) showed little variation from 35.4 to 47.0 kV/mm, regardless of the PS time. On the other hand, that of the thin ones (0.05 mm) dramatically decreased from 99.5 to 9.8 kV/mm with increased the PS time from 6 to 48 h. Because the DBS sharply decreased at the thin substrate sintered for longer time in which some large-elongated grains might span the substrate thickness-wise throughout, it was inferred that the interface between β-Si₃N₄ grains and grain boundary phase/intergranular glassy films might be a path of the dielectric breakdown.     

A behavioral model for optically powered OCT endoscope with a micro electrostatic vertical‐comb optical scanner

This paper presents a novel device architecture for optically actuated microelectromechanical systems (MEMS) endoscopes for optical coherence tomography (OCT) measurement. A 10‐mW infrared light beam at a wavelength of 1.5 µm is transferred through the single‐mode fiber to provide a scanning MEMS mirror with the drive voltage (maximum 11 V) by exciting a photovoltaic cell, while also providing with a secondary light beam at a wavelength of 1.3 µm for the OCT measurement. An electrostatic vertical comb‐drive optical scanner (1.5 mm × 2.0 mm × 0.5 mm) has been developed by using the deep reactive ion etching (DRIE) of a silicon‐on‐insulator (SOI) wafer. The design of the scanner module is discussed, along with the experimental results of electrostatic operation. An equivalent circuit model for the optical scanner is developed to explain the behavior of the optically powered actuation mechanism, including the hysteresis loop in the frequency response and the voltage dependence of oscillating angle (mechanical peak ±3.2°/7 V around the resonance frequency of 250 Hz). OCT measurement of a tissue is demonstrated to reconstruct the cross‐sectional image of a fingerprint at a resolution of lateral 40 µm × vertical 8 µm and penetration depth of 2.5 mm. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Effect of different features to drill-wear prediction with back propagation neural network

In this paper, a back propagation neural network (BPNN) has been applied to predict the corner wear of a high speed steel (HSS) drill bit for drilling on different workpiece materials. Specially defined static and dynamic features extracted by a wavelet packet transform (WPT) from the resultant force converted from thrust and torque together with the cutting conditions (workpiece material, spindle speed, drill diameter, feed rate) are used as inputs to train the network to obtain a better output, drill corner wear. Drilling experiments have been carried out over a wide range and, features newly defined and conventional ones, features extracted from different frequency bands are compared.     

Antioxidant Effects of Herbal Tea Leaves from Yacon (Smallanthus sonchifolius) on Multiple Free Radical and Reducing Power Assays,Especially on Different Superoxide Anion Radical Generation Systems

Yacon (Smallanthus sonchifolius), a native Andean plant, has been cultivated as a crop and locally used as a traditional folk medicine for the people suffering from diabetes and digestive/renal disorders. However, the medicinal properties of this plant and its processed foods have not been completely established. This study investigates the potent antioxidative effects of herbal tea leaves from yacon in different free radical models and a ferric reducing model. A hot‐water extract exhibited the highest yield of total polyphenol and scavenging effect on 1,1‐diphenyl‐2‐picryl hydrazyl (DPPH) radical among four extracts prepared with hot water, methanol, ethanol, and ethylacetate. In addition, a higher reducing power of the hot‐water extract was similarly demonstrated among these extracts. Varying concentrations of the hot‐water extract resulted in different scavenging activities in four synthetic free radical models: DPPH radical (EC₅₀ 28.1 μg/mL), 2,2′‐azinobis(3‐ethylbenzothiazoline‐6‐sulfonic acid) cation radical (EC₅₀ 23.7 μg/mL), galvinoxyl radical (EC₅₀ 3.06 μg/mL), and chlorpromazine cation radical (EC₅₀ 475 μg/mL). The yacon tea‐leaf extract further demonstrated superoxide anion (O₂^?) radical scavenging effects in the phenazine methosulfate‐NADH‐nitroblue tetrazolium (EC₅₀ 64.5 μg/mL) and xanthine oxidase assay systems (EC₅₀ 20.7 μg/mL). Subsequently, incubating human neutrophilic cells in the presence of the tea‐leaf extract could suppress the cellular O₂^? radical generation (IC₅₀ 65.7 μg/mL) in a phorbol 12‐myristate 13‐acetate‐activated cell model. These results support yacon tea leaves may be a good source of natural antioxidants for preventing O₂^? radical‐mediated disorders.     

Effect of cellular inositol content on ethanol tolerance of Saccharomyces cerevisiae in sake brewing

The effect of cellular inositol content on the ethanol tolerance of sake yeast was investigated. In a static culture of strain K901 in a synthetic medium, when cells were grown in the presence of inositol in limited amount (L-cells), the inositol content of cells decreased by one-third that of cells grown in the presence of inositol in sufficient amount (H-cells). L-cells exhibited a higher death rate constant than H-cells in the presence of 12-20% ethanol, while no difference in specific ethanol production rate in the presence of 0-18% ethanol between the two cell types was observed. L-cells leaked more intracellular components, such as nucleotides, phosphate and potassium, in the presence of ethanol than H-cells. L-cells exhibited a lower intracellular pH value than H-cells, which represented the lowering of cell vitality by the decrease in H(+) extrusion activity. Furthermore, the plasma membrane H(+)-ATPase activity of L-cells was approximately one-half of that of H-cells. Therefore, it was considered that the decrease in viability in the presence of ethanol due to inositol limitation results from the lowering of H(+)-ATPase activity, which maintains the permeability barrier of the yeast membrane, ensuring the homeostasis of ions in the cytoplasm of yeast cells. It is assumed that the lowering of H(+)-ATPase activity due to inositol limitation is caused by the change in lipid environment of the enzyme, which is affected by inositol-containing glycerophospholipids such as phosphatidylinositol (PI), because in the PI-saturated mixed micellar assay system, the difference in H(+)-ATPase activity between L- and H-cells disappeared. In the early stage of sake mash, inositol limitation lowers the ethanol tolerance due to the decrease in H(+)-ATPase activity as in static culture. In the final stage of sake mash, the disruption of the ino1 gene responsible for inositol synthesis, resulted in a decrease in cell density. Furthermore, the ino1 disruptant, which was not capable of increasing the cellular inositol level in the final stage, exhibited a significantly higher methylene blue-staining ratio than the parental strain. It was suggested that the yeast cellular inositol level is one of the important factors which contribute to the high ethanol tolerance implied by the increased cell viability in the presence of ethanol.     

Use of a Metal-mould Process in the Development of Hemispherical Heavy-walled Castings

The exacting quality required of hemispherical heavy-walled steel castings, used in nuclear power applications, has been remarkably improved by the adoption of a newly developed metal-mould process. This technique is dependent on the use of a metal core. The optimum conditions for solidification were determined by the finite element analytical method. The appropriate wall-thickness of the chill elements was also investigated using data based on actual experience. The core was designed in such a manner that the surface carried a series of concave “dimples” in the manner of a golf-ball, the pattern being intended to prevent the formation of cracks, generated on the casting surface when in contact with a metal mould. Stresses caused by solidification shrinkage were reduced by splitting the core. In the event, the casting structure conformed well to the results of the solidification analysis. Radiographic examination revealed a high level of soundness, with no trace of internal defects. No anisotropy was detected in mechanical properties. It is shown that this process is being currently employed in the manufacture of actual products.     

Incentive‐rewarding mechanism to stimulate activities in social networking services

We have developed an incentive‐rewarding mechanism that stimulates activities in social networking services (SNSs), including content uploading and link establishment. We particularly focus on changing the reward assignment ratio based on the different risks users perceive when uploading content with different privacy settings: public‐open and friend‐limited. Learning‐based simulation allowed us to observe that SNS activity, which we measured as the amount of browsed content within a certain period, can be controlled by a rewarding assignment ratio. We then analyzed how the amount of uploaded content and the increase of established links affect SNS activity. Results suggested that the optimal reward assignment ratio to maximize SNS activity changes depending on the total amount of available reward resources. Copyright © 2011 John Wiley & Sons, Ltd.     

A novel coding method for genetic algorithms based on redundant binary numbers

This article proposes a novel genetic algorithm (GA) which switches the expression of the solution from a redundant binary number to a usual binary number. Furthermore, a GA which switches the expression from the Gray code to the usual binary number is proposed and compared. Comparisons of the performances among five GAs (binary number, redundant binary number, Gray code, switching from redundant binary number to binary number, switching from Gray code to binary number) are illustrated. The performances are evaluated by solving some equations. It is confirmed that the proposed GA effectively decreases the error rate.