Numerical study on dynamic behavior of slope models including weak layers from deformation to failure using material point method

This paper describes numerical studies on the dynamic behavior of experimental slope models, including various inclined weak layers. These studies were conducted by simulation of shaking table tests using the material point method (MPM), which allows seamless treatment of various considerations, from elastic behavior to discontinuous collapse behavior of slopes, on the basis of an elasto-plastic constitutive law. The simulation results showed that the failure modes, progressive deformation and downward sliding of the numerical slope models, which were similar to that observed in the shaking table tests, can be obtained using the numerical method. In addition, sensitivity analyses of the numerical models used in this study were performed to determine the effects of mesh size, number of particles per cell (PPC) and damping constants on the simulation results. The results of these analyses indicated the use of fine meshes and high damping constants seems to produce sensible results and reduce numerical noises, respectively.     

Development of numerical analysis method of flow-acoustic resonance in stub pipes of safety relief valves

The boiling water reactors (BWRs) have steam dryer in the upper part of the pressure vessel to remove moisture from the steam. The steam dryer in the Quad Cities Unit 2 nuclear power plant was damaged by high-cycle fatigue due to acoustic-induced vibration during extended power uprate operation. The principal source of the acoustic-induced vibration was flow-acoustic resonance at the stub pipes of the safety relief valves (SRVs) in the main steam lines (MSLs). The acoustic wave generated at the SRV stub pipes propagates throughout the MSLs and eventually reaches and damages the steam dryer. Therefore, for power uprate operation of the BWRs, it has been required to predict the flow-acoustic resonance at the SRV stub pipes. The purpose of this article was to propose a numerical analysis method for evaluating the flow-acoustic resonance in the SRV stub pipes. The proposed method is based on the finite difference lattice Boltzmann method (FDLBM). So far, the FDLBM has been applied to flow-acoustic simulations of laminar flows around simple geometries at low Reynolds number. In order to apply the FDLBM to the flow-acoustic resonance simulations of turbulent flows around complicated geometries at the high Reynolds number, we developed computationally efficient model by introducing new function into the governing equation. The proposed method was compared with the conventional FDLBM in the cavity-driven flow simulation. The proposed method was validated by comparisons with the experimental data in the 1/10-scale test of BWR-5 under atmosphere condition. The following three results were obtained; the first is that the proposed method can reduce the computing time by 30% compared with the conventional FDLBM; the second is that the proposed method successfully simulated the flow-acoustic resonance in the SRV stub pipes of the BWR-5, and the pressure fluctuations of the simulation results agreed well with those of the experimental data; and the third is the mechanism of the flow-acoustic resonance in the SRV stub pipes. Acoustic waves causing the flow-acoustic resonance in the SRV stub pipes are generated by the unsteady vortices in the SRV stub pipes.     

Fabrication of ZnO films consisting of densely accumulated mesoporous nanosheets and their dye-sensitized solar cell performance

Nanocrystalline and mesoporous ZnO films approximately 4 μm in thickness were fabricated through a simple chemical deposition of Zn₄CO₃(OH)₆·H₂O in an aqueous solution of zinc nitrate and urea and subsequent pyrolysis at a low temperature of 300 °C. Microscopic observation of the films revealed that they were composed of mesoporous nanosheets accumulating with submicrometer-order spacing between them on conducting glass substrates. Adsorption of N-719 dye onto the ZnO surface, for application to dye-sensitized solar cells, led to dye-loading of 1.1 × 10^− 7 mol/cm² in spite of the relatively small thickness. The resultant ZnO/N-719 photoanode exhibited a short-circuit photocurrent density of 13.8 mA/cm², which is of the highest level ever reported for ZnO. An overall light-to-electricity conversion efficiency of 3.3% was achieved under 1 sun AM1.5 illumination without any optimization in view of the other cell components.     

Isotopomer analysis of production and consumption mechanisms of N2O and CH4 in an advanced wastewater treatment system

Wastewater treatment processes are believed to be anthropogenic sources of nitrous oxide (N(2)O) and methane (CH(4)). However, few studies have examined the mechanisms and controlling factors in production of these greenhouse gases in complex bacterial systems. To elucidate production and consumption mechanisms of N(2)O and CH(4) in microbial consortia during wastewater treatment and to characterize human waste sources, we measured their concentrations and isotopomer ratios (elemental isotope ratios and site-specific N isotope ratios in asymmetric molecules of NNO) in water and gas samples collected by an advanced treatment system in Tokyo. Although the estimated emissions of N(2)O and CH(4) from the system were found to be lower than those from the typical treatment systems reported before, water in biological reaction tanks was supersaturated with both gases. The concentration of N(2)O, produced mainly by nitrifier-denitrification as indicated by isotopomer ratios, was highest in the oxic tank (ca. 4000% saturation). The dissolved CH(4) concentration was highest in in-flow water (ca. 3000% saturation). It decreased gradually during treatment. Its carbon isotope ratio indicated that the decrease resulted from bacterial CH(4) oxidation and that microbial CH(4) production can occur in anaerobic and settling tanks.     

A Unique Amino Transfer Mechanism for Constructing the β‐Amino Fatty Acid Starter Unit in the Biosynthesis of the Macrolactam Antibiotic Cremimycin

Cremimycin is a 19‐membered macrolactam glycoside antibiotic based on three distinctive substructures: 1) a β‐amino fatty acid starter moiety, 2) a bicyclic macrolactam ring, and 3) a cymarose unit. To elucidate the biosynthetic machineries responsible for these three structures, the cremimycin biosynthetic gene cluster was identified. The cmi gene cluster consists of 33 open reading frames encoding eight polyketide synthases, six deoxysugar biosynthetic enzymes, and a characteristic group of five β‐amino‐acid‐transfer enzymes. Involvement of the gene cluster in cremimycin production was confirmed by a gene knockout experiment. Further, a feeding experiment demonstrated that 3‐aminononanoate is a direct precursor of cremimycin. Two characteristic enzymes of the cremimycin‐type biosynthesis were functionally characterized in vitro. The results showed that a putative thioesterase homologue, CmiS1, catalyzes the Michael addition of glycine to the β‐position of a non‐2‐enoic acid thioester, followed by hydrolysis of the thioester to give N‐carboxymethyl‐3‐aminononanoate. Subsequently, the resultant amino acid was oxidized by a putative FAD‐dependent glycine oxidase homologue, CmiS2, to produce 3‐aminononanoate and glyoxylate. This represents a unique amino transfer mechanism for β‐amino acid biosynthesis.     

Development of a tube-type solar still equipped with heat accumulation for irrigation

A tube-type solar still is found to be suitable for use in desert irrigation. The effectiveness of a heat accumulator with regard to distillate productivity is experimentally and numerically verified. The heat accumulator consists of tube bundles immersed in wax in order to utilize the latent heat of wax. The dynamic response to stepwise variation of irradiative intensity verified the contribution of wax to an increase of productivity only when the phase change of wax occurred. The effective distillate productivity was found to be 294.3 g/m² during the cyclic stepwise change of irradiative intensity, from 200 to 600 W/m² and back. Velocity vectors driven by natural convection and temperature contours estimated by numerical simulation verified the effectiveness of the heat accumulator especially after peak solar intensity. The latent heat of wax effectively contributed to a 15% increase in total distillate productivity per day. The still can feasibly meet irrigation water supply demands above an irrigative threshold of 17 MJ/m² d.     

Theranostic Agent Combining Fullerene Nanocrystals and Gold Nanoparticles for Photoacoustic Imaging and Photothermal Therapy

Developing photoactivatable theranostic platforms with integrated functionalities of biocompatibility, targeting, imaging contrast, and therapy is a promising approach for cancer diagnosis and therapy. Here, we report a theranostic agent based on a hybrid nanoparticle comprising fullerene nanocrystals and gold nanoparticles (FGNPs) for photoacoustic imaging and photothermal therapy. Compared to gold nanoparticles and fullerene crystals, FGNPs exhibited stronger photoacoustic signals and photothermal heating characteristics by irradiating light with an optimal wavelength. Our studies demonstrated that FGNPs could kill cancer cells due to their photothermal heating characteristics in vitro. Moreover, FGNPs that are accumulated in tumor tissue via the enhanced permeation and retention effect can visualize tumor tissue due to their photoacoustic signal in tumor xenograft model mice. The theranostic agent with FGNPs shows promise for cancer therapy.     

Effect of Electron Correlation on Angular Dependence of Magnetoconductivity

We have measured the electrical resistivities and magnetoresistances (MR) of (EDT-DSDTFVO)₂X (X=FeCl₄, GaCl₄), where EDT-DSDTFVO stands for ethylenedithiodiselenadithiafulvalenothioquinone-1,3-dithiolemethide. These materials undergo gradual metal-insulator transitions at T_min=52 K for FeCl₄-salt and T_min=30 K for GaCl₄-salt, respectively. In spite of the similarity of the temperature dependence of the resistivity and its pressure effect, MR of both salts exhibit a clear contrast, i.e. FeCl₄-salt shows negative and GaCl₄, positive. Origin of the difference in the sign of MR between these salts are discussed in terms of the existence of π-d interaction.     

Sacubitril/Valsartan Improves Diastolic Function But Not Skeletal Muscle Function in a Rat Model of HFpEF

The angiotensin receptor/neprilysin inhibitor Sacubitril/Valsartan (Sac/Val) has been shown to be beneficial in patients suffering from heart failure with reduced ejection fraction (HFrEF). However, the impact of Sac/Val in patients presenting with heart failure with preserved ejection fraction (HFpEF) is not yet clearly resolved. The present study aimed to reveal the influence of the drug on the functionality of the myocardium, the skeletal muscle, and the vasculature in a rat model of HFpEF. Female obese ZSF-1 rats received Sac/Val as a daily oral gavage for 12 weeks. Left ventricle (LV) function was assessed every four weeks using echocardiography. Prior to organ removal, invasive hemodynamic measurements were performed in both ventricles. Vascular function of the carotid artery and skeletal muscle function were monitored. Sac/Val treatment reduced E/é ratios, left ventricular end diastolic pressure (LVEDP) and myocardial stiffness as well as myocardial fibrosis and heart weight compared to the obese control group. Sac/Val slightly improved endothelial function in the carotid artery but had no impact on skeletal muscle function. Our results demonstrate striking effects of Sac/Val on the myocardial structure and function in a rat model of HFpEF. While vasodilation was slightly improved, functionality of the skeletal muscle remained unaffected.     

Oxidation of aniline to nitrobenzene by nonheme bromoperoxidase

Nonheme bromoperoxidase found in Pseudomonas putida catalyzed the bromination of aniline with hydrogen peroxide and bromide ions to give o- and p-bromoanilines. However, in the absence of bromide ions, it oxidized aniline via azobenzene and azoxybenzene finally into nitrobenzene. This is the first report of the biological oxidation of an arylamine to the corresponding nitrocompound at the enzyme level. In addition, nitrobenzene was not formed by a nonheme bromoperoxidase from Corallina pilulifera (marine alga), implying that the alga enzyme has a different reaction mechanism.