Numerical study on dynamic behavior of slope models including weak layers from deformation to failure using material point method

This paper describes numerical studies on the dynamic behavior of experimental slope models, including various inclined weak layers. These studies were conducted by simulation of shaking table tests using the material point method (MPM), which allows seamless treatment of various considerations, from elastic behavior to discontinuous collapse behavior of slopes, on the basis of an elasto-plastic constitutive law. The simulation results showed that the failure modes, progressive deformation and downward sliding of the numerical slope models, which were similar to that observed in the shaking table tests, can be obtained using the numerical method. In addition, sensitivity analyses of the numerical models used in this study were performed to determine the effects of mesh size, number of particles per cell (PPC) and damping constants on the simulation results. The results of these analyses indicated the use of fine meshes and high damping constants seems to produce sensible results and reduce numerical noises, respectively.     

Development of numerical analysis method of flow-acoustic resonance in stub pipes of safety relief valves

The boiling water reactors (BWRs) have steam dryer in the upper part of the pressure vessel to remove moisture from the steam. The steam dryer in the Quad Cities Unit 2 nuclear power plant was damaged by high-cycle fatigue due to acoustic-induced vibration during extended power uprate operation. The principal source of the acoustic-induced vibration was flow-acoustic resonance at the stub pipes of the safety relief valves (SRVs) in the main steam lines (MSLs). The acoustic wave generated at the SRV stub pipes propagates throughout the MSLs and eventually reaches and damages the steam dryer. Therefore, for power uprate operation of the BWRs, it has been required to predict the flow-acoustic resonance at the SRV stub pipes. The purpose of this article was to propose a numerical analysis method for evaluating the flow-acoustic resonance in the SRV stub pipes. The proposed method is based on the finite difference lattice Boltzmann method (FDLBM). So far, the FDLBM has been applied to flow-acoustic simulations of laminar flows around simple geometries at low Reynolds number. In order to apply the FDLBM to the flow-acoustic resonance simulations of turbulent flows around complicated geometries at the high Reynolds number, we developed computationally efficient model by introducing new function into the governing equation. The proposed method was compared with the conventional FDLBM in the cavity-driven flow simulation. The proposed method was validated by comparisons with the experimental data in the 1/10-scale test of BWR-5 under atmosphere condition. The following three results were obtained; the first is that the proposed method can reduce the computing time by 30% compared with the conventional FDLBM; the second is that the proposed method successfully simulated the flow-acoustic resonance in the SRV stub pipes of the BWR-5, and the pressure fluctuations of the simulation results agreed well with those of the experimental data; and the third is the mechanism of the flow-acoustic resonance in the SRV stub pipes. Acoustic waves causing the flow-acoustic resonance in the SRV stub pipes are generated by the unsteady vortices in the SRV stub pipes.     

Isotopomer analysis of production and consumption mechanisms of N2O and CH4 in an advanced wastewater treatment system

Wastewater treatment processes are believed to be anthropogenic sources of nitrous oxide (N(2)O) and methane (CH(4)). However, few studies have examined the mechanisms and controlling factors in production of these greenhouse gases in complex bacterial systems. To elucidate production and consumption mechanisms of N(2)O and CH(4) in microbial consortia during wastewater treatment and to characterize human waste sources, we measured their concentrations and isotopomer ratios (elemental isotope ratios and site-specific N isotope ratios in asymmetric molecules of NNO) in water and gas samples collected by an advanced treatment system in Tokyo. Although the estimated emissions of N(2)O and CH(4) from the system were found to be lower than those from the typical treatment systems reported before, water in biological reaction tanks was supersaturated with both gases. The concentration of N(2)O, produced mainly by nitrifier-denitrification as indicated by isotopomer ratios, was highest in the oxic tank (ca. 4000% saturation). The dissolved CH(4) concentration was highest in in-flow water (ca. 3000% saturation). It decreased gradually during treatment. Its carbon isotope ratio indicated that the decrease resulted from bacterial CH(4) oxidation and that microbial CH(4) production can occur in anaerobic and settling tanks.     

Novel grounded and floating high order immittance simulators using OTAs and OAs

This paper proposes novel grounded and floating high order series and parallel immittance simulators using operational transconductance amplifiers (OTAs) and operational amplifiers (OAs) with a finite gain–bandwidth (GB) product. They are composed of active devices (OTAs and OAs) and resistances, and are suitable for monolithic implementation in either CMOS or bipolar technologies. They also realize both positive and negative high order immittances. The circuit characteristics can be electronically tuned by adjusting the transconductances of OTAs and the GB products of OAs. Any transfer functions are realizable using the proposed simulators. Two examples are shown, together with simulation results.     

Development of a tube-type solar still equipped with heat accumulation for irrigation

A tube-type solar still is found to be suitable for use in desert irrigation. The effectiveness of a heat accumulator with regard to distillate productivity is experimentally and numerically verified. The heat accumulator consists of tube bundles immersed in wax in order to utilize the latent heat of wax. The dynamic response to stepwise variation of irradiative intensity verified the contribution of wax to an increase of productivity only when the phase change of wax occurred. The effective distillate productivity was found to be 294.3 g/m² during the cyclic stepwise change of irradiative intensity, from 200 to 600 W/m² and back. Velocity vectors driven by natural convection and temperature contours estimated by numerical simulation verified the effectiveness of the heat accumulator especially after peak solar intensity. The latent heat of wax effectively contributed to a 15% increase in total distillate productivity per day. The still can feasibly meet irrigation water supply demands above an irrigative threshold of 17 MJ/m² d.     

High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

A Unique Amino Transfer Mechanism for Constructing the β‐Amino Fatty Acid Starter Unit in the Biosynthesis of the Macrolactam Antibiotic Cremimycin

Cremimycin is a 19‐membered macrolactam glycoside antibiotic based on three distinctive substructures: 1) a β‐amino fatty acid starter moiety, 2) a bicyclic macrolactam ring, and 3) a cymarose unit. To elucidate the biosynthetic machineries responsible for these three structures, the cremimycin biosynthetic gene cluster was identified. The cmi gene cluster consists of 33 open reading frames encoding eight polyketide synthases, six deoxysugar biosynthetic enzymes, and a characteristic group of five β‐amino‐acid‐transfer enzymes. Involvement of the gene cluster in cremimycin production was confirmed by a gene knockout experiment. Further, a feeding experiment demonstrated that 3‐aminononanoate is a direct precursor of cremimycin. Two characteristic enzymes of the cremimycin‐type biosynthesis were functionally characterized in vitro. The results showed that a putative thioesterase homologue, CmiS1, catalyzes the Michael addition of glycine to the β‐position of a non‐2‐enoic acid thioester, followed by hydrolysis of the thioester to give N‐carboxymethyl‐3‐aminononanoate. Subsequently, the resultant amino acid was oxidized by a putative FAD‐dependent glycine oxidase homologue, CmiS2, to produce 3‐aminononanoate and glyoxylate. This represents a unique amino transfer mechanism for β‐amino acid biosynthesis.     

Thermal and electrical conduction properties of vertically aligned carbon nanotubes produced by water-assisted chemical vapor deposition

We present both thermal and electrical conduction properties of vertically aligned carbon nanotubes (VACNTs), synthesized by the water-assisted chemical vapor deposition method using Fe–Ti–O nanoparticles as catalyst. Thermal diffusivity and electrical resistance of VACNTs have been measured by the laser flash method and direct-current four-terminal method, respectively. The VACNTs are found to have thermal diffusivities of the same order as isotropic graphite and the electrical characteristics of semiconductors. The electrical resistance shows a T^−1/4 temperature dependence, which implies that the conduction of electrons is dominated by 3D Mott variable range hopping.     

2-Arachidonoyl glycerol suppresses gastric emptying via the cannabinoid receptor 1-cholecystokinin signaling pathway in mice

2-Monoacylglycerol (2-MAG) is one of the digestion products of dietary lipids. We recently demonstrated that a 2-MAG, 2-arachidonoyl glycerol (2-AG) potently stimulated cholecystokinin (CCK) secretion via cannabinoid receptor 1 (CB1) in a murine CCK-producing cell line, STC-1. CCK plays a crucial role in suppressing postprandial gastric emptying. To examine the effect of 2-AG on gastric emptying, we performed acetaminophen and phenol red recovery tests under oral or intraperitoneal administration of 2-AG in mice. Orally administered 2-AG (25 mg/kg) suppressed the gastric emptying rate in mice, as determined by the acetaminophen absorption test and phenol red recovery test. Intraperitoneal administration of a cholecystokinin A receptor antagonist (0.5 mg/kg) attenuated the gastric inhibitory emptying effect. In addition, both oral (10 mg/kg) and intraperitoneal (0.5 mg/kg) administration of a CB1 antagonist counteracted the 2-AG-induced gastric inhibitory effect. Furthermore, intraperitoneal 2-AG (25 mg/kg) suppressed gastric emptying. These results indicate that 2-AG exhibits an inhibitory effect on gastric emptying in mice, possibly mediated by stimulating both CCK secretion via CB1 expressed in CCK-producing cells and acting on CB1 expressed in the peripheral nerves. Our findings provide novel insights into the 2-MAG-sensing mechanism in enteroendocrine cells and the physiological role of 2-MAG.     

Primary Sj?gren's syndrome followed by chronic myelogenous leukemia: a case report with a ten year history

We describe a female patient with primary Sj?gren's syndrome who subsequently developed chronic myelogenous leukemia. The patient received a bone marrow transplant (BMT) from a genotypically HLA-identical brother after pre-transplant preparation with busulfan and cyclophosphamide. Eighteen weeks later, cutaneous and mucosal chronic graft-versus-host disease developed, followed by death 11 months after transplantation. Anti-Ro/SS-A antibodies disappeared within 6 months post-BMT, but antinuclear antibodies remained positive through the post-transplant course.