Rapid erasing of wettability patterns based on TiO2-PDMS composite films

TiO₂-polydimethylsiloxane (TiO₂-PDMS) composite films are prepared using the sol–gel method from a Ti(OBu)₄–benzoylacetone solution containing PDMS. The prepared films are cured by irradiation with ultraviolet (UV) light. Structural changes in the films after UV irradiation are confirmed by UV–vis absorption experiments, which show that an absorption band characteristic of the benzoylacetonate chelate rings disappears. This finding is ascribed to structural changes associated with the dissociation of the chelate rings. The IR spectra of the thin films exhibit a broad absorption band after UV irradiation, indicating that a Ti–O–Ti network forms in the thin film. Contact angles are measured for the TiO₂-PDMS thin films, showing wettability conversion from hydrophobic to superhydrophilic states by irradiation with oxygen plasma for 1 s. This phenomenon is explained by XPS experiments which reveal that the number of carbon atoms decreases, whereas the number of oxygen atoms increases on the surface of the TiO₂-PDMS composite films. Finally, hydrophobic–superhydrophilic patterns are fabricated based on a patterned TiO₂-PDMS composite film. The film displays a rapid change to superhydrophilicity over the whole film surface upon plasma irradiation for 1 s, which means that the wettability patterns are rapidly erasable.     

A near-field-sensing transceiver for intrabody communication based on the electrooptic effect

This paper describes a near-field-sensing transceiver for intrabody communication, in which the human body is the transmission medium. The key component of the transceiver is an electric-field sensor implemented with an electrooptic crystal and laser light. This sensor is suitable for detection of the small and unstable electric fields produced by the human body because it has extremely high input impedance. This transceiver enables IEEE 802.3 half-duplex communication of 10 Mb/s through a person's body in an operating range of about 150 cm between the hands. The packet error rate of 0.04% is obtained at packet size of 1070 octet. This paper explains the configuration and performance of the transceiver and presents results of a communication test.     

Fabrication and characterizations of PCDTBT: PC71BM bulk heterojunction solar cell using air brush coating method

Organic solar cells have been significantly attracted due to the need to develop an inexpensive clean and sustainable renewable energy source. We report on the fabrication of poly [N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]/[6, 6]-phenyl-C₇₁-butyric acid methyl ester blend active layer using airbrush spray-coating method in mixed solvents. Optical absorption of the active layers was analyzed using UV–visible spectral studies in the wavelength range from 300 to 800 nm. The surface morphology of the active layers deposited with different parameters (spraying time and substrate-nozzle distance) was examined using atomic force microscopy. The current density–voltage (J–V) characteristics of photovoltaic cells were measured under the illumination of simulated solar light with 100 mW cm^?2 (AM 1.5G) by an Oriel 1000 W solar simulator. The power conversion efficiency of the solar cell is more than 5 %.     

Fabrication of ZnO films consisting of densely accumulated mesoporous nanosheets and their dye-sensitized solar cell performance

Nanocrystalline and mesoporous ZnO films approximately 4 μm in thickness were fabricated through a simple chemical deposition of Zn₄CO₃(OH)₆·H₂O in an aqueous solution of zinc nitrate and urea and subsequent pyrolysis at a low temperature of 300 °C. Microscopic observation of the films revealed that they were composed of mesoporous nanosheets accumulating with submicrometer-order spacing between them on conducting glass substrates. Adsorption of N-719 dye onto the ZnO surface, for application to dye-sensitized solar cells, led to dye-loading of 1.1 × 10^− 7 mol/cm² in spite of the relatively small thickness. The resultant ZnO/N-719 photoanode exhibited a short-circuit photocurrent density of 13.8 mA/cm², which is of the highest level ever reported for ZnO. An overall light-to-electricity conversion efficiency of 3.3% was achieved under 1 sun AM1.5 illumination without any optimization in view of the other cell components.     

High-cycle fatigue characteristics of quasi-isotropic CFRP laminates over 10 cycles (Initiation and propagation of delamination considering interaction with transverse cracks)

High-cycle fatigue features of over 10⁸ cycles, particularly the initiation and propagation of edge delamination considering the effects of transverse cracks, were investigated using quasi-isotropic carbon-fiber-reinforced plastic (CFRP) laminates with a stacking sequence of [45/0/−45/90]_s in this study. In the relationship between a transverse crack density and initiation and growth of edge delamination, it was found that fatigue damage growth behavior varied depending on applied stress. It was observed that edge delamination initiated and grew at parts where transverse cracks were dense at ordinary applied stress, whereas it was observed that edge delamination grew before or simultaneously with transverse crack propagation at a low applied stress and high-cycle loading. In addition, the critical transverse crack density where delamination begins growing was calculated to evaluate the interaction between transverse crack and edge delamination growth.     

Fabrication of damascene Cu wirings using solid acidic catalyst

The copper damascene process is one of the most promising technologies for fabricating Cu wirings for electronic devices such as LSIs. In this research, the fabrication of damascene Cu wirings was conducted using solid acidic catalyst. When a Cu-plated wafer, whose oxide is a basic oxide is dipped into a mixture of oxidizing solution and acidic solution, surface atoms are ionized and etched off into the solution. However, because conventional nonelectrolytic etching does not have a reference surface, it is difficult to utilize for planarization. Therefore, a new nonelectrolytic machining method using a cation-exchange fabric instead of an acidic solution was developed. To be more precise, the planarization of a Cu-plated wafer was carried out by rubbing with the cation-exchange fabric in ozone water. Basically, this method exploits chemical reactions so that the physical properties of the workpiece surface are not deteriorated. Furthermore, this method uses no chemicals except for ozone water, which easily dissociates into water and oxygen molecules; thus, this method is a low-cost, environmentally friendly process. In this paper, as a preliminary experiment, the nonelectrolytic etching of a Cu sample using solutions of O₃ and CO₂ was carried out to inspect the dependence of the etching rate on [O₃] and [H⁺]. The results indicate that the etching rate increased as [O₃] and [H⁺] increased. When [H⁺] was high relative to [O₃], a smooth etch-pit-free surface was achieved. Next, nonelectrolytic etching using a cation-exchange fabric was carried out, and properties similar to those in the case of etching using solutions were obtained. Finally, damascene Cu wirings were fabricated using ozone water and a cation-exchange catalyst.     

Revolving Vernier Mechanism Controls Size of Linear Homomultimer

A new kind of the Vernier mechanism that is able to control the size of linear assembly of DNA origami nanostructures is proposed. The mechanism is realized by mechanical design of DNA origami, which consists of a hollow cylinder and a rotatable shaft in it connected through the same scaffold. This nanostructure stacks with each other by the shape complementarity at its top and bottom surfaces of the cylinder, while the number of stacking is limited by twisting angle of the shaft. Experiments have shown that the size distribution of multimeric assembly of the origami depends on the twisting angle of the shaft; the average lengths of the multimer are decamer, hexamer, and tetramer for 0°, 10°, and 20° twist, respectively. In summary, it is possible to affect the number of polymerization by adjusting the precise shape and movability of a molecular structure.     

Stress analysis with arbitrary body force by boundary element method

Linear stress analysis without body force can be easily carried out by means of the boundary element method. Some cases of linear stress analysis with body force can also be solved without the domain integral. However domain integrals are generally necessary to solve the linear stress problems with complicated body forces. This paper shows that the linear stress problems with complicated body forces can be solved approximately without the domain integral. In order to solve these problems, the domain is divided into small areas using contour lines of body force. In these areas, the distributions of body force are assumed approximately to satisfy the Laplace equation.     

Repeated temperature modulation epitaxy for p-type doping and light-emitting diode based on ZnO.

Since the successful demonstration of a blue light-emitting diode (LED), potential materials for making short-wavelength LEDs and diode lasers have been attracting increasing interest as the demands for display, illumination and information storage grow. Zinc oxide has substantial advantages including large exciton binding energy, as demonstrated by efficient excitonic lasing on optical excitation. Several groups have postulated the use of p-type ZnO doped with nitrogen, arsenic or phosphorus, and even p-n junctions. However, the choice of dopant and growth technique remains controversial and the reliability of p-type ZnO is still under debate. If ZnO is ever to produce long-lasting and robust devices, the quality of epitaxial layers has to be improved as has been the protocol in other compound semiconductors. Here we report high-quality undoped films with electron mobility exceeding that in the bulk. We have used a new technique to fabricate p-type ZnO reproducibly. Violet electroluminescence from homostructural p-i-n junctions is demonstrated at room-temperature.