Bending fatigue strength of case-carburized helical gears (In the case of large helix angles)

Case-carburizing enlarges the depth of the hardened layer at the tooth width end on the acute angle side of helical gears. For the helical gears with large helix angles (Exceeding 25°), this hardened layer may lower their bending fatigue strength. Therefore, we investigated the influence of this hardened layer on their bending fatigue strength through the bending fatigue tests. Our results suggest that this hardened layer might reduce the case-carburizing’s effect to enhance their bending fatigue strength. Thus, using only the maximum tooth root stress would be inadequate for evaluating their bending fatigue strength, and it would be necessary to consider the relationship between the hardened layer and the tooth root stress distribution (Especially, the stress applied at the tooth width end on the acute angle side) from the beginning of meshing to the end.     

Processing of Novel Strontium Titanate-Based Thin-Film Varistors by Chemical Solution Deposition

Strontium titanate (SrTiO₃)-based multilayered film with varistor characteristics has successfully been fabricated by a chemical solution deposition (CSD) method. Homogeneous precursor solutions of SrTiO₃ and Nb:SrTiO₃ with long-term stability could be prepared by optimizing the reaction conditions among strontium ethoxide, titanium isopropoxide, and niobium ethoxide. Films were prepared using the precursor solutions on fused silica substrates at 700°C. Triple layered films with SrTiO₃/Nb:SrTiO₃/SrTiO₃ structure were also successfully crystallized on Pt/Ti/SiO₂/Si substrates at 700°C. The current–voltage ( I - V ) curve of the multilayered film was characteristic to varistors and the nonlinear coefficient α of the synthesized film was ∼3.0. The varistor voltages ( E _0.01) of 0.6-μm-thick film were 140 kV/cm for the forward direction and −120 kV/cm for the reverse direction, respectively, at room temperature.     

Model study on the formation of fuel NOx from cokes on combustion: Effect of metal oxides

To elucidate the process of ‘fuel NO_x’ formation from cokes and chars on combustion, carbons obtained from urea-resin and melamine-resin were subjected to combustion under a stream of pure oxygen at temperatures between 600 °C and 1000 °C. The carbons subjected to combustion without any additives produced a relatively small amount of NO_x, but, it was observed that the NO_x formation predominated at lower temperatures of combustion. When the combustion was carried out with the addition of metal oxides, such as iron oxides and cupric oxide, the amount of NO_x formed increased markedly but silicon dioxide had no such effect.     

Lubrication in steel strip rolling in Japan

Research into, and the state of technology for, lubrication in steel strip rolling in Japan are reviewed. Both cold and hot strip rolling are discussed. Subjects covered include coefficient of friction and oil film thickness, friction pick-up, and roll wear.     

Application of accelerators for the research and development of scintillators

We introduce experimental systems which use accelerators to evaluate scintillation properties such as scintillation intensity, wavelength, and lifetime. A single crystal of good optical quality is often unavailable during early stages in the research and development (R&D) of new scintillator materials. Because of their beams' high excitation power and/or low penetration depth, accelerators facilitate estimation of the properties of early samples which may only be available as powders, thin films, and very small crystals. We constructed a scintillation spectrum measurement system that uses a Van de Graaff accelerator and an optical multichannel analyzer to estimate the relative scintillation intensity. In addition, we constructed a scintillation time profile measurement system that uses an electron linear accelerator and a femtosecond streak camera or a microchannel plate photomultiplier tube followed by a digital oscilloscope to determine the scintillation lifetimes. The time resolution is approximately 10 ps. The scintillation spectra or time profiles can be obtained in a significantly shorter acquisition time in comparison with that required by conventional measuring systems. The advantages of the systems described in this study can significantly promote the R&D of novel scintillator materials.     

Fracture Toughness Analysis of Advanced Ceramic Composite for Hip Prosthesis

The fracture behavior of a zirconia-toughened alumina-matrix composite (added with small amounts of mixed oxides) for ceramic hip joint prostheses has been evaluated with emphasis placed on the effect of environmental surface degradation in moist environment. Accelerated aging tests were performed up to 300 h in an autoclave operating at 121°C (under 0.1 MPa pressure) in vapor environment, which represents a quite severe environmental testing condition. Besides conventional fracture mechanics characterizations, including different types of fracture toughness test, microscopic insight into the effect of environmental surface degradation on toughness could be obtained according to Raman and fluorescence microprobe spectroscopy. The main outcomes of this study were as follows: (i) after 10-h autoclaving (according to ISO standard recommendation) no significant change of monoclinic volume fraction and fracture toughness could be detected; (ii) after very long exposure time (300 h) the monoclinic phase content increased and the surface fracture toughness decreased by approximately 30%, although it was still above the toughness level of pure alumina; and (iii) the bulk toughness was unaffected by autoclave exposure, independent of exposure time elongation.     

Thermal behavior of aluminum-coated 22MnB5 in hot stamping under dry and lubricated conditions

The hot stamping of aluminum-coated 22MnB5 has usually been conducted under dry condition, for which the forming load is high since the coefficient of friction is over 0.5. In order to decrease the forming load, the authors previously proposed the use of a lubricant to decrease so that the coefficient of friction from over 0.5 to 0.3. However, it is necessary to understand the heat transfer property in hot stamping under lubricated condition. The purpose of this paper is to examine the heat transfer property of aluminum-coated 22MnB5 in hot stamping under dry and lubricated conditions. In this study, the die and specimen temperatures were measured during compression and compression-sliding tests under dry and lubricated conditions using the hot flat drawing test simulator. In the compression test, the die and specimen temperatures measured under dry and lubricated conditions were the same. On the other hand, in the compression-sliding test up to a sliding distance of 70 mm, the die temperature under lubricated condition was lower than that under dry condition, and it was found that the heat transfer under lubricated condition is superior to that under dry condition. Consequently, there is a difference between the specimen temperatures under dry and lubricated conditions. However, from the results of the tensile test, there is no difference between the tensile strengths under dry and lubricated conditions.     

Effect of trehalose accumulation on response to saline stress in Saccharomyces cerevisiae

To examine the effect of trehalose accumulation on response to saline stress in Saccharomyces cerevisiae, we constructed deletion strains of all combinations of the trehalase genes ATH1, NTH1 and NTH2 and examined their growth behaviour and intracellular trehalose accumulation under non‐stress and saline‐stress conditions. Saline stress was induced in yeast cells by NaCl addition at the exponential growth phase. All deletion strains showed similar specific growth rates and trehalose accumulation to their parent strain under non‐stress conditions. However, under the saline stress condition, one single deletion strain, nth1Δ, two double deletion strains, nth1Δ ath1Δ and nth1Δ nth2Δ, and the triple deletion strain nth1Δnth2Δ ath1Δ, all of which carry the nth1Δ deletion, showed increased trehalose accumulation as compared to the parent and other deletion strains. In particular, our statistical analysis revealed that the triple deletion strain showed a higher growth rate under the saline stress condition than the parent strain. Moreover, some deletion strains showed further trehalose accumulation under non‐stress conditions by overexpression of the TPS1 or TPS2 genes encoding the enzymes related to trehalose biosynthesis at the mid‐exponential phase. Such increased trehalose accumulation prior to NaCl addition could improve the growth of these strains under saline stress. Our results indicate that high trehalose accumulation prior to NaCl addition, rather than after NaCl addition, is necessary to achieve high growth activity under stress conditions. Copyright © 2009 John Wiley & Sons, Ltd.     

A multi-objective cost–benefit optimization algorithm for network hardening

International Journal of Information Security - Network hardening is an optimization problem to find the best combination of countermeasures to protect a network from cyber-attacks. While an...     

Enhancement of arachidonic acid production by Mortierella alpina 1S-4

The effect of mineral addition on arachidonic acid (AA) production by Mortierella alpina 1S-4 was evaluated. At first, the addition of minerals such as sodium, potassium, calcium, and magnesium was examined in flask cultures, and then the addition of phosphorus with the optimal amounts of the minerals was investigated in a 10-L jar-fermenter. As a result, 1.5% soy flour medium with the addition of 0.3% KH₂PO₄, 0.1% Na₂SO₄, 0.05% CaCl₂·2H₂O, and 0.05% MgCl₂·6H₂O was found to enhance the AA yield 1.7-fold over that without mineral addition. When 1% yeast extract with the above mineral mixture was used, the AA yield was enhanced 1.35-fold over that without minerals. We also verified that an increase in the polar lipid content occurred in the case of only KH₂PO₄ addition, and that the above-mentioned increase in the AA yield was due to the minerals themselves, not a pH buffer effect.