Three-dimensional time-averaged void fraction distribution measurement technique for BWR thermal hydraulic conditions using an X-ray CT system

We have developed a void fraction distribution measurement technique using the three-dimensional (3D) time-averaged X-ray computed tomography (CT) system to understand two-phase flow behavior inside a fuel bundle for boiling water reactor (BWR) thermal hydraulic conditions of 7.2 MPa and 288 °C. As a first step, we measured the 3D void fraction distribution in a vertical square (5?×?5) rod array that simulated a BWR fuel bundle in the air–water test. A comparison of the volume-averaged void fractions evaluated by the developed X-ray CT system with those evaluated by a differential pressure transducer showed satisfactory agreement within a difference of 0.03. Thus, we confirmed that the developed system could be used to get 3D imaging of the vertical square rod array used in the test under the BWR operating pressure condition. In the next step, we did a verification test using the vertical pipe (11.3 mm ID) for BWR thermal hydraulic conditions. A comparison of the cross-sectional-averaged void fractions evaluated by the X-ray CT system with those evaluated by the drift-flux model showed good agreement within a difference of 0.05. We confirmed that the evaluated void fraction distribution forms in the horizontal cross section changed with the quality in response to the flow regime transition.     

Feeder components and instrumentation for the JT-60SA magnet system

The modifying of the JT-60U magnet system to the superconducting coils is progressing as a satellite facility for ITER by both parties of Japanese government and European commission in the Broader Approach agreement. The magnet system requires current supplies of 25.7 kA for 18 TF coils and of 20 kA for 4 CS modules and 6 EF coils. The magnet system generates an average heat load of 3.2 kW at 4 K to the cryogenic system. The feeder components connected to the power supply provide current supply. The cooling pipes connected to the cryogenic system provide coolant supply. The instrumentation of the JT-60SA magnet system is used for its operation.     

The alkylation of biphenyl over three-dimensional large pore zeolites: The influence of zeolite structure and alkylating agent on the selectivity for 4,4′-dialkylbiphenyl

Catalytic properties of three-dimensional zeolites, Y (FAU), Beta (BEA), and CIT-1 (CON) zeolites were examined in the alkylation, isopropylation, sec-butylation, and tert-butylation, of biphenyl (BP), and compared to those of H-mordenite (MOR). The selectivities for 4,4′-dialkylbiphenyl (4,4′-DABP) varied with the types of zeolite and of alkylating agent. FAU, BEA, and CON gave only low selectivities for 4,4′-diisopropylbiphenyl (4,4′-DIPB) in the isopropylation, and predominant isomers were bulky and thermodynamically unstable 2,x′-DIPB (2,2′-, 2,3′-, and 2,4′-) at lower temperatures, and bulky and thermodynamically stable 3,4′- and 3,3′-DIPB at higher temperatures: this is quite different from catalytic features over MOR, which gave 4,4′-DIPB with high selectivities at moderate temperatures. These results suggest that FAU, BEA, and CON have no shape-selective nature in the isopropylation, and that the reaction is principally controlled kinetically at lower temperatures, and thermodynamically at higher temperatures. The sec-butylation gave similar results to the isopropylation. Although the selectivities for 4,4′-di-sec-butylbiphenyl (4,4′-DSBB) were higher than those in the isopropylation, predominant isomers were 2,x′-DSBB (2,2′-, 2,3′-, and 2,4′-) at lower temperatures, and 3,4′- and 3,3′-DSBB at higher temperatures. The tert-butylation gave 4,4′-di-tert-butylbiphenyl (4,4′-DTBB) in moderate to high selectivities over all zeolites at moderate temperatures: the selectivity for 4,4′-DTBB was higher than 80% over BEA and CON; however, it still remained at 50% over FAU. FAU channels with super cages are too large for selective formation of 4,4′-DTBB.

From these results, it is concluded that the selectivity for 4,4′-DABP in the alkylation over MOR, FAU, BEA, and CON is determined by the exclusion of bulky isomers at their transition states, and that the exclusion is caused by the steric restriction at the transition states of bulky isomers by the zeolite channels.     

Adsorption of cationic monomeric and gemini surfactants on montmorillonite and adsolubilization of vitamin E

Adsorption of a cationic gemini surfactant (1,2-bis(dodecyldimethylammonio) ethane dibromide, 12-2-12) and the corresponding monomeric surfactant (dodecyltrimethylammonium bromide, DTAB) on montmorillonite has been characterized with a combination of adsorption isotherm, interlayer spacing and FT-IR spectroscopic data. Adsolubilization of vitamin E into the adsorbed surfactant layers has also been studied. The adsorption isotherm data reveal that the adsorption of the two surfactants is driven by the two factors: one is the cation exchange that occurs on the interlayer basal planes and the other is the hydrophobic interaction between hydrocarbon chains of the surfactants. Although the adsorbed amount measured in the saturation region (in mol g(-1)) is almost identical for the two surfactants, the conformation of the intercalated surfactant molecules differs significantly from each other. The adsorption of DTAB results in a lateral bilayer arrangement in the limited interlayer space, whereas 12-2-12 gives a normal bilayer arrangement in the expanded interlayer space. Adsolubilization of vitamin E takes place into the adsorbed surfactant layers, and interestingly, all the vitamin E molecules added in the montmorillonite suspensions are hybridized at lower surfactant concentrations due to the great specific surface area of the clay material. Since the maximum adsolubilization amount is usually obtained just below the critical micelle concentration, the gemini surfactant is deemed to be more efficient than the corresponding monomeric one to achieve the great adsolubilization amount.     

Effects of flow rate on sensitivity and affinity in flow injection biosensor systems studied by 55-MHz wireless quartz crystal microbalance

In this paper, we developed a 55-MHz wireless-electrodeless quartz crystal microbalance (QCM) and systematically studied the effects of flow rate on the sensitivity to the detection of proteins and on the affinity between biomolecules evaluated by the flow injection system. Brownian motion of proteins in liquid suggests a low probability of meeting, and the convection effect plays an important role in the sensitivity and the affinity in the flow cell injection system. The wireless quartz crystal was isolated in the QCM cell, and flow rates between 50 and 1000 microL/min were used for monitoring binding reactions between human immunoglobulin G and Staphylococcus aureus protein A. The sensitivity was significantly increased as the flow rate increased, while the affinity value remained unchanged. However, the affinity value was affected by the reaction time for a large-concentration analyte, indicating the need of a high-sensitivity biosensor system for accurate evaluation of affinity. The electrode effect on the QCM sensitivity was also theoretically investigated, showing that the electrode significantly deteriorates the QCM sensitivity and makes the Sauerbrey equation invalid.     

Study of hydrogen and deuterium emission characteristics in laser-induced low-pressure helium plasma for the suppression of surface water contamination

An experimental study was conducted in search of the experimental condition required for the much needed suppression of spectral interference caused by surface water in hydrogen analysis using laser-induced low-pressure helium plasma spectroscopy. The problem arising from the difficulty in distinguishing hydrogen emission from hydrogen impurity inside the sample and that coming from the water molecules was overcome by taking advantage of similar emission characteristics shared by hydrogen and deuterium demonstrated in this experiment by the distinct time-dependent and pressure-dependent variations of the D and H emission intensities from the D-doped zircaloy-4 samples. This similarity allows the study of H impurity emission in terms of D emission from the D-doped samples and thereby separating it from the H emission originating from the water molecules. Employing this strategy has allowed us to achieve the large suppression of water induced spectral interference from the previous minimum of 400 microg/g to the current value of 30 microg/g when a laser beam of 34 mJ under tight focusing condition was employed. Along with this favorable result, this experimental condition has also provided a much better (about 6-fold higher) spatial resolution, although these results were achieved at the expense of reducing the linear calibration range from the previous 4 300 microg/g to the present 200 microg/g.     

Estimates of embodied global energy and air-emission intensities of Japanese products for building a Japanese input-output life cycle assessment database with a global system boundary

To build a life cycle assessment (LCA) database of Japanese products embracing their global supply chains in a manner requiring lower time and labor burdens, this study estimates the intensity of embodied global environmental burden for commodities produced in Japan. The intensity of embodied global environmental burden is a measure of the environmental burden generated globally by unit production of the commodity and can be used as life cycle inventory data in LCA. The calculation employs an input-output LCA method with a global link input-output model that defines a global system boundary grounded in a simplified multiregional input-output framework. As results, the intensities of embodied global environmental burden for 406 Japanese commodities are determined in terms of energy consumption, greenhouse-gas emissions (carbon dioxide, methane, nitrous oxide, perfluorocarbons, hydrofluorocarbons, sulfur hexafluoride, and their summation), and air-pollutant emissions (nitrogen oxide and sulfur oxide). The uncertainties in the intensities of embodied global environmental burden attributable to the simplified structure of the global link input-output model are quantified using Monte Carlo simulation. In addition, by analyzing the structure of the embodied global greenhouse-gas intensities we characterize Japanese commodities in the context of LCA embracing global supply chains.     

Large-scale genome reorganization in Saccharomyces cerevisiae through combinatorial loss of mini-chromosomes

A highly efficient technique, termed PCR-mediated chromosome splitting (PCS), was used to create cells containing a variety of genomic constitutions in a haploid strain of Saccharomyces cerevisiae. Using PCS, we constructed two haploid strains, ZN92 and SH6484, that carry multiple mini-chromosomes. In strain ZN92, chromosomes IV and XI were split into 16 derivative chromosomes, seven of which had no known essential genes. Strain SH6484 was constructed to have 14 mini-chromosomes carrying only non-essential genes by splitting chromosomes I, II, III, VIII, XI, XIII, XIV, XV, and XVI. Both strains were cultured under defined nutrient conditions and analyzed for combinatorial loss of mini-chromosomes. During culture, cells with various combinations of mini-chromosomes arose, indicating that genomic reorganization could be achieved by splitting chromosomes to generate mini-chromosomes followed by their combinatorial loss. We found that although non-essential mini-chromosomes were lost in various combinations in ZN92, one mini-chromosome (18kb) that harbored 12 genes was not lost. This finding suggests that the loss of some combination of these 12 non-essential genes might result in synthetic lethality. We also found examples of genome-wide amplifications induced by mini-chromosome loss. In SH6484, the mitochondrial genome, as well as the copy number of genomic regions not contained in the mini-chromosomes, was specifically amplified. We conclude that PCS allows for genomic reorganization, in terms of both combinations of mini-chromosomes and gene dosage, and we suggest that PCS could be useful for the efficient production of desired compounds by generating yeast strains with optimized genomic constitutions.     

Ultrahigh Electrical Resistance of Poly(cyclohexyl methacrylate)/Carbon Nanotube Composites Prepared Using Surface‐Initiated Polymerization

Multiwalled carbon nanotubes on which poly(cyclohexyl methacrylate)s are densely grafted (PCHMA‐CNTs), are synthesized using a modified surface‐initiated atom transfer radical polymerization technique. The electrical resistance of PCHMA‐CNT is systematically characterized under direct current (DC) and alternating current and compared to that of conventional nanocomposites prepared by blending PCHMA with the CNT (PCHMA/CNT). At a comparable volume fraction of CNT, DC volume resistivity of PCHMA‐CNT is 14 orders of magnitude higher than that of PCHMA/CNT. This is because the grafted polymer with a combination of the high molecular weight and the high grafting density isolates individual CNTs at a long distance in the PCHMA‐CNT system. In addition, impedance analysis reveals that the highly insulated PCHMA‐CNT has the same electrical nature as neat PCHMA, i.e., it is a dielectric. Furthermore, dynamic mechanical analysis shows PCHMA‐CNT has a good mechanical properties as well as ultrahigh electrical resistance.