Self-assembly of three dimensional micro mechanisms using thermal shrinkage of polyimide

This paper describes three-dimensional microstructures fabricated using a simple self-assembly process involving the thermal shrinkage of polyimide. The proposed method enables hinged structures to be automatically rotated out of the wafer plane and to remain bent without the need to use any interlocking mechanisms. The hinged structures were fabricated using surface micromachining techniques involving heating in a furnace. An increase in the bending angle due to the shrinkage of polyimide was observed with increasing heating temperature, heating time, and length of the polyimide hinge. Of these three parameters, the heating time was found to be the most suitable for precise control of the bending angle. Furthermore, microcubes were fabricated by this method and the self-assembly process was successfully visualized using a CCD camera.     

Accelerator-driven system for transmutation of high-level waste

The accelerator-driven transmutation system has been studied at the Japan Atomic Energy Research Institute. This system is a hydrid system which consists of a high intensity accelerator, a spallation target and a subcritical core region. In the conceptual design study, two types of system concepts, sodium cooled and lead-bismuth cooled system, are being studied. In this study, we fucus on our lead-bismuth cooled accelerator-driven transmutation system to investigate basic characteristics. The fuel compositions were optimized for efficient transmutation of minor actinide. The transmutation of long-lived fission products was also considered.     

Experimental Evaluation of Characteristics of SR Motor Made of Permendur

A switched reluctance (SR) motor has a doubly salient pole structure. The performance of the SR motor strongly depends on the magnetic properties of the core material, since it consists only of an iron core and copper windings. This study experimentally evaluates the performance of an SR motor made of permendur (Fe–49% Co alloy), which has very high saturation flux density and low core loss. Two types of SR motors that have the same dimensions but different core materials are used: one motor is made of the conventional nonoriented Si steel, and the other is made of permendur. Comparison of the characteristics of the two motors shows that the performance of the permendur SR motor surpasses that of the conventional one in terms of output power and efficiency. © 2014 Wiley Periodicals, Inc. Electr Eng Jpn, 187(1): 51–57, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22431     

Reduction of Vibration in Concentrated Winding Permanent Magnet Synchronous Motor by Means of Skew Effects of Rotor

Global warming and the problem of successfully incorporating environmental safeguards are promoting the need for a more power‐efficient motor. Therefore, as a driving source, permanent magnet synchronous motors (PMSMs) with concentrated winding are widely used in a variety of fields. However, a PMSM with a concentrated winding generates more vibration than one with a distributed winding because of the radial electromagnetic force. This paper describes the effect of a new skewed rotor on the characteristics of a concentrated winding PMSM. We investigated this effect by three‐dimensional finite element method (3D FEM) analysis and measurement. We also demonstrate that the proposed rotor is effective in reducing the radial electromagnetic force without decreasing motor efficiency. © 2014 Wiley Periodicals, Inc. Electr Eng Jpn, 187(2): 33–43, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22400     

Risk assessment for gas pipelines using fuzzy sets

Most gas pipelines have been buried for many years and it is hard to assess their safety. In some locations, gas pipeline breaks have resulted in severe economic and social consequences. The severity of such consequences increases with the number of people exposed. For these reasons, risk assessment for gas pipeline systems should consider both the prediction of damage occurrence and the estimation of the economic and social impacts. In this paper, a new measure denoted H. Index is introduced to assess the magnitude of gas accidents. In order to examine the correlation between the magnitude of accidents and the pipeline attributes, including the environment, fuzzy component analysis is developed. This paper presents a procedure based on linguistic variables to evaluate the main characteristics for each accident. Actual accidents data in Japan are used to illustrate the approach.     

Fracture behaviour and numerical study of resistance spot welded joints in high-strength steel sheet

Cross tension tests of resistance spot welded joints with varying nugget diameter were carried out using 980 MPa high strength steel sheet of 1.6 mm thickness. In proportion, as nugget diameter increased from 3√t to 5√t (where t is thickness), cross tension strength (CTS) increased while fracture morphology simultaneously transferred from interface fracture to full plug fracture. In cases of interface fracture, circumferential crack initiation due to separation of the corona bond arose at an early stage of loading. The crack opening process without propagation was recognized until just before fracture and then the crack propagated to the nugget immediately in a brittle manner around CTS. In full plug fracture, main ductile crack initiation from the notch-like part at the end of sheet separation occurred with the sub-crack initiated at an early stage. The ductile crack propagated toward the HAZ and base material to form full plug fracture. The mode I stress intensity factor was considered as a suitable fracture parameter because the circumferential crack behaved pre-crack for brittle fracture in the nugget region at the final stage. Based on the FE analysis, the mode I stress intensity factor was calculated as 116 MPa √m at CTS as fracture toughness for the nugget. With respect to full plug fracture, ductile crack initiation behaviour from the notch-like part was expressed by concentration of equivalent plastic strain. On the assumption that the ductile crack arose in critical value of equivalent plastic strain, the value was calculated as 0.34 by FE analysis. Reasonable interpretation for interface fracture and full plug fracture in the resistance spot welded joint was proposed due to first crack initiation by stress concentration, brittle fracture by using mode I stress intensity factor, and ductile crack initiation by using equivalent plastic strain.     

Cerebral Hyperperfusion after Revascularization Inhibits Development of Cerebral Ischemic Lesions Due to Artery-to-Artery Emboli during Carotid Exposure in Endarterectomy for Patients with Preoperative Cerebral Hemodynamic Insufficiency: Revisiting the “Impaired Clearance of Emboli” Concept

The purpose of the present study was to determine whether cerebral hyperperfusion after revascularization inhibits development of cerebral ischemic lesions due to artery-to-artery emboli during exposure of the carotid arteries in carotid endarterectomy (CEA). In patients undergoing CEA for internal carotid artery stenosis (≥70%), cerebral blood flow (CBF) was measured using single-photon emission computed tomography (SPECT) before and immediately after CEA. Microembolic signals (MES) were identified using transcranial Doppler during carotid exposure. Diffusion-weighted magnetic resonance imaging (DWI) was performed within 24 h after surgery. Of 32 patients with a combination of reduced cerebrovascular reactivity to acetazolamide on preoperative brain perfusion SPECT and MES during carotid exposure, 14 (44%) showed cerebral hyperperfusion (defined as postoperative CBF increase ≥100% compared with preoperative values), and 16 (50%) developed DWI-characterized postoperative cerebral ischemic lesions. Postoperative cerebral hyperperfusion was significantly associated with the absence of DWI-characterized postoperative cerebral ischemic lesions (95% confidence interval, 0.001–0.179; p = 0.0009). These data suggest that cerebral hyperperfusion after revascularization inhibits development of cerebral ischemic lesions due to artery-to-artery emboli during carotid exposure in CEA, supporting the “impaired clearance of emboli” concept. Blood pressure elevation following carotid declamping would be effective when embolism not accompanied by cerebral hyperperfusion occurs during CEA.     

Structure and viscoelastic properties of segmented polyurethane blends

Structure and viscoelastic properties of segmented polyurethanurea (SPU) blends were investigated. The glass transition temperature (T_g) of poly(tetramethylene glycohol) (PTMG) in a soft-segment block of the component SPU increased with decreasing molecular weight of PTMG. The blend samples showed two T_gs of PTMG in the temperature dispersions of the loss modulus (E″) and loss tangent (tan δ). The value of E′ in the leathery region for the blend specimens was trongly affected by the morphology. The blends were considered to have a morphology where PTMG differing in molecular weight was localized. © 1996 John Wiley & Sons, Inc.     

Fracture and acoustic emission characteristics of glass fiber reinforced plastics panels for hot water

This study deals with the fracture process and acoustic emission (AE) characteristics of a randomly oriented E-glass fiber mat reinforcement with a crosslinked polyester. These panels were evaluated after they were immersed in hot water. The fiber volume content of the panel was 19%. Glass fiber reinforced plastics (GFRP) panels wer immersed in water at 81°C. Bending and AE monitoring tests were Performed and after bending, the cross-section of the specimen was observed by an optical microscope and SEM. The influence of degradation, due to water immersion, on the changes of fracture process of GFRP is discussed. The dominant fracture mode of the virgin specimen was matrix cracks, whereas that of the immersed specimen was debondings at the fiber bundle/matrix and fiber/matrix interfaces. This change was caused by reduction of the bonding strength at the interface. The scale of fracture can be estimated by both AE amplitude and AE energy and this estimation method was used to estimate the fracture mode changes of GFRP panels immersed in hot water.     

Fluorescent in situ hybridization analysis of open lactic acid fermentation of kitchen refuse using rRNA-targeted oligonucleotide probes

Reproducible amounts of lactic acid accumulate in minced kitchen refuse under open conditions with intermittent pH neutralization [Sakai et al., Food Sci. Technol. Res., 6, 140 (2000)]. Here, we showed that such pH-controlled open fermentation of kitchen refuse reproducibly resulted a selective proliferation of a major lactic acid bacterial (LAB) species. In one experiment, the predominant microorganisms isolated during the early phase (6 h) were Gammaproteobacteria. In contrast, those that predominated during the late phase (48 h) were always Lactobacillus plantarum in three independent experiments. To further quantify the microbial community within open lactic acid fermentation, we performed fluorescent in situ hybridization (FISH) analysis targeting 16S (23S) rRNA. We designed two new group-specific DNA probes: LAC722(L) was active for most LAB including the genera Lactobacillus, Pediococcus, Leuconostoc and Weisella, whereas Lplan477 was specific for L. plantarum and its related species. We then optimized sample preparation using lysozyme and hybridization conditions including temperature, as well as the formamide concentration and the salt concentration in the washing buffer. We succeeded in quantification of microorganisms in semi-solid, complex biological materials such as minced kitchen refuse by taking color microphotographs in modified RGB balance on pre-coated slides. FISH analysis of the fermentation of kitchen refuse indicated that control of the pH swing leads to domination by the LAB population in minced kitchen refuse under open conditions. We also confirmed that L. plantarum, which generates lactic acid in high quantities but with low optical activity, became the dominant microorganism in kitchen refuse during the late phase of open fermentation.