Microwave permeability of single cobalt nanotube studied by micromagnetics simulations and generalized Snoek’s law

Microwave permeability spectra of single Co nanotube under equilibrium state have been studied by micromagnetics simulation.More than four obvious resonance peaks have been found(11.72,24.20,33.18 and 39.55 GHz).Such large resonance frequency cannot be found in other traditional magnetic materials.The configurations of magnetic moments along the nanotube have been simulated.The results show that the top end of nanotube has a"flow-out"pattern of magnetic moments configuration.The bottom end has a"flow-in"pattern of magnetic moments configuration.The magnetic moments within the main body of nanotube are aligned perfectly along the length of nanotube.The magnitude of natural resonance peak is strongly related to the volume fraction of a zone,which has the same orientation of magnetic moments.Large microwave permeability values have been found for single nanotube.The generalized Snoek’s law has been used to validate the micromagnetics simulations in this paper.     

Mode III fracture of a magnetoelectroelastic layer: exact solution and discussion of the crack face electromagnetic boundary conditions

This paper develops a closed-form solution for anti-plane mechanical and in plane electric and magnetic fields in a magnetoelectroelastic layer of finite thickness. Explicit expressions for the stresses, electric fields, and magnetic fields, together with their intensity factors are obtained for the extreme cases for impermeable and permeable cracks. Solutions for some special cases, such as a magnetoelectroelastic layer with infinite thickness, are also obtained. Applicability of the crack face electromagnetic boundary conditions is discussed. It is found that the crack profile is important in obtaining the correct electromagnetic fields and their intensity factors. The stress intensity factor, however, does not depend on the crack face electromagnetic boundary condition assumptions.     

Particularities of condensation of atoms with increased kinetic energy

Novel universal method for measurement of the condensation coefficient α is developed. Using this method, noticeable difference between measured (α≈0.8) and expected (α≈1) values of the condensation coefficient for sputtered Cr atoms was revealed for the first time. The effect is assumed to be a result of considerable elevation of the surface temperature during atomic condensation induced by the energy delivered to the condensation surface by sputtered atoms and from the plasma.     

High performance series-resonance energy-recovery circuit for plasma display panel

A new high performance series-resonance energy-recovery circuit (ERC) for a plasma display panel (PDP) is proposed. Two different ERCs are used for both sides of the PDP, and the slow falling and fast rising times are employed. Therefore, it features the zero voltage switching, low electromagnetic interference, low current stress, no severe voltage notch, and high energy-recovery capability.     

中国(大陆)粉末冶金零件行业2004年进展

本文介绍了中国（大陆）粉末冶金零件行业2004年的生产概况与市场动向。阐述了粉末冶金汽车零件的市场动态。分析了中国（大陆）粉末冶金零件行业面临的挑战。介绍了美国APMI International的PMT认证。     

生物脱氮技术处理废水的应用实践

对废水生物脱氮工艺的开工调试进行了分析,通过对污泥的培养、驯化、使活性污泥达到最佳的污水处理状态。对在调试过程中出现的问题提出相应的改进措施,进一步降低了外排水生化指标。     

级数sum from n=1 to ∞(α(α-1)…(α-n+1)x~n/n!)在x=±1处的敛散性研究

用比较原则及莱布尼兹判别法对函数f(x)=(1+x)α的马克劳林级数在x=±1的敛散情形给予讨论.     

Dynamic deformation behavior of ultrafine-grained low-carbon steels fabricated by equal-channel angular pressing

The dynamic deformation behavior of ultrafine-grained low-carbon steels fabricated by equal-channel angular pressing (ECAP) was investigated in this study. Dynamic torsional tests, using a torsional Kolsky bar, were conducted on four steel specimens, two of which were annealed at 480 °C after ECAP, and then the test data were compared in terms of microstructures, tensile properties, and adiabatic shear-band formation. The equal-channel angular pressed specimen consisted of very fine, equiaxed grains of 0.2 to 0.3 μm in size, which were slightly coarsened after annealing. The dynamic torsional test results indicated that maximum shear stress decreased with increasing annealing time, whereas fracture shear strain increased. Some adiabatic shear bands were observed at the gage center of the dynamically deformed torsional specimen. Their width was smaller in the equal-channel angular pressed specimen than in the 1-hour-annealed specimen, but they were not found in the 24-hour-annealed specimen. Ultrafine, equiaxed grains of 0.05 to 0.2 μm in size were formed inside the adiabatic shear band, and their boundaries had characteristics of high-angle grain boundaries. These phenomena were explained by dynamic recrystallization due to a highly localized plastic strain and temperature rise during dynamic deformation.     

Effect of Hot Band Annealing on Magnetic Properties in 3% Si Grain‐oriented Electrical Steels

Hot band annealing is known to be a prerequisite for good magnetic properties irrespective of manufacturing methods in grain‐oriented Fe‐3 wt.% Si electrical steels. In this study, the effects of hot band annealing on magnetic properties were investigated in 3% grain‐oriented electrical steels of low soluble AI contents and one‐stage cold rolling. Microstructure and precipitate distribution were compared with hot band annealing conditions. Secondary recrystallization behaviour with hot band annealing condition was also discussed.