Mild hydrocracking of 1-methyl naphthalene (1-MN) over alumina modified zeolite

The catalytic activity and life of the NiMoS supported on alumina–USY zeolite (physical mixture of alumina and USY (NMAZ), USY zeolite coated with alumina (NMACZ-2)) were compared in the hydrocracking of 1-methyl naphthalene by a single run at the several reaction temperatures between 360 and 400 °C as well as repeated runs at 360 °C. The relative activity of NMAZ is slightly higher after 1 h at all reaction temperatures, but was lower after 2 h at reaction temperatures above 380 °C. The preference of NMACZ-2 became distinct and definite by further increasing the reaction time at all reaction temperatures. Too long reaction time, particularly at higher reaction temperature, decreased the yield of (alkyl)benzenes, indicating the significant progress of the successive reactions. Thus, the highest yield of alkyl(benzenes) of about 97% was obtained over NMACZ-2 after 4 h at 380–390 °C. This was much less than the yield of about 82% obtained over NMAZ after 4 h at 370 °C. Ten repeated runs at 360 °C for 6 h resulted in marked decrease of yield over NMAZ from 73% to 64%, while the decrease in yield over NMACZ-2 was only from about 80% to 78%. The decrease of catalytic activity appears to reflect the coke formation on the USY which occurs on the naked acidic site of the substrate, which are rather isolated from the NiMoS on alumina. In contrast, alumina-coated support keeps USY underneath the alumina, which carries NiMoS and acidic sites on the same surface. The acidity of surface alumina is moderated by the underneath USY. The adequate acidity of the neighboring NiMoS and high hydrogenation activity provide a good balance resulting in an excellent catalytic activity and life of NiMoS supported on alumina-coated USY zeolite.     

Polymerization behavior of methylol-functional benzoxazine monomer

This study focuses on methylol functional benzoxazines as precursors to build a network structure utilizing both benzoxazine and resole chemistry. The first part is a review of systems that contain methylol groups which play a role on their crosslinking formation. The polymerization mechanism and properties of resoles will be highlighted as the most abundant polymers that are characterized by polymerization through condensation reaction of methylol group. In the second part, the effect of incorporating methylol group into benzoxazine monomers is studied. Differential scanning calorimetry (DSC) is used to study the effect of methylol group on the rate of polymerization. Kissinger and Ozawa methods using non-isothermal DSC at different heating rates show that methylol monomer exhibits lower average activation energy compared to the un-functionalized monomer. The effect of adding catalysts into the monomers is also studied. p-Toluene sulfonic acid (PTSA) is found to be more efficient than 1-methyl-imidazole (IMD) and lithium iodide (LiI) in the case of methylol monomer due to its ability of accelerating both the methylol condensation and ring-opening polymerization. Additionally, thermal behavior of the monomers is studied using thermogravimetric analysis (TGA).     

Removal of toxic aqueous ions using amorphous AlPO4

Aluminium phosphate (AlPO₄) was characterized using X-ray diffractometry (XRD), Fourier Transform infrared (FTIR), point of zero charge (PZC) and dissolution studies. XRD showed the sample to be amorphous, FTIR confirmed the presence of OH groups on the surface and PZC was determined at pH 3.45. The dissolution study illustrated a decrease in dissolution with an increase in the pH. Potentiometric titration data were fit to the Gaines–Thomas equation, which showed that AlPO₄ is a weakly acidic ion exchanger. Sorption studies were carried out at pH 4–6 and temperatures 293–323 K. The uptake of metal ions was observed to increase with an increase in the pH and temperature. The surface selectivity towards metal ions was found in the order Pb²⁺> Cu²⁺> Cd²⁺. Sorption data were fit to the new equation derived from the proposed mechanism for metal ion uptake. Various parameters such as stoichiometry of the surface H⁺ ion release, equilibrium constant, standard enthalpy, entropy and free energy changes were evaluated from the plots. The values of all these parameters were found to be closely related to the values reported in the literature.     

Comparative Study on Microstructures of Zincalume Steel (G550) Welded Joint Between Metal Inert Gas and Laser Beam Welding

Zincalume steel (G550) is commonly used in various construction fields because of its high corrosion resistance and good mechanical properties. In recent years, a number of steel companies have massively produced zincalume steel (G550) with large volumes of waste. For the reduction of massive industrial wastes, the zincalume steel (G550) was welded in the lap joint configuration using different welding parameters in the metal inert gas (MIG) welding and laser beam welding (LBW) process in this study. The MIG welding and LBW are more welcomed welding methods due to their high efficiency and low cost. However, they are different as the LBW offers welding speed three to five times faster than MIG welding, while LBW’s heat transfer to workpieces is much less than MIG welding, which can avoid some distortions. The microstructure of zincalume steel (G550) was investigated using scanning electron microscopy (SEM) and the microstructure characterizations of welded specimens were analyzed. The experiment found the columnar dendrites extended under the heat flow direction during the MIG welding and LBW process. Thus, the columnar grains were formed in between the equiaxed zone and fusion zone (FZ) at high heat input and slow cooling rate. Moreover, the grain size of FZ was comparatively smaller than heat affected zone (HAZ) and base metal (BM).     

Reactive supercritical fluid extrusion for development of moisture resistant starch‐based foams

The main objective of this work was to reduce barriers that prevent the usage of starch‐based foams by understanding the effect and the sequence of dual‐modification of crosslinked (XL) and acetylated (Ac) starch in one continuous supercritical fluid reactive extrusion (SCFX) process on wetting properties, physicochemical properties, and cellular structure of solid foam. The starch was reacted with epichlorohydrin (EPI) and acetic anhydride (Ac) under alkaline conditions in a twin‐screw extruder in the presence of supercritical carbon dioxide (SC‐CO₂). An increase in EPI concentration from 0.00 to 3.00% increased the degree of crosslinking as measured by DSC and confirmed by the quantification of the glucose units in the solution after acid hydrolysis. We observed a reduction of the glucose units from 93.07% for 0.00% EPI to 6.73% when 3.00% EPI was added. With crosslinking/acetylation processing, contact angle was higher for modified starches, indicating that chemical treatments induced dramatic changes in their surface polarity. Compared with native, the contact angle for dual modified starch increased from 43.1° to 91.7° which indicated their lower wettability. The addition of SC‐CO₂, EPI, and Ac to the formulation reduced the density of the extrudates and increased the expansion ratio. The average cell size in the extrudate determined by scanning electron microscopy was also found to decrease from 150 to 34 μm by the addition of the two reagents. Moreover, the dual‐modification of starches provided more hardness and adhesiveness to the extrudates than was observed for the unmodified starches. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Impact of frying on key fatty acid ratios of canola oil

The study was carried out to investigate the changes in saturated (SFA), monoene (MUFA), trans (TFA), and polyunsaturated (PUFA) fatty acids and the key fatty acid ratios (SFA/UFA, cis PUFA/SFA, C18:2/C16:0 and C18:3/C16:0) during potato chips frying in canola oil using single bounce attenuated total reflectance FTIR (SB‐ATR‐FTIR) spectroscopy. The data obtained from GC‐FID were used as reference. The calibration of main fat groups and their key fatty acid ratios were developed by partial least square (PLS) regression coefficients using 4000 to 650 cm^?1 spectral range. FTIR PLS regression for the predicted SFA, MUFA, TFA, and PUFA were found 0.999, 0.998, 0.998, and 0.999, respectively, whereas for SFA/UFA, cis PUFA/SFA, C18:2/C16:0 and C18:3/C16:0 the regression coefficients were 0.991, 0.997, 0.996, and 0.994, respectively. We conclude that FTIR‐PLS could be used for rapid and accurate assessment of changes in the main fat groups and their key fatty acid ratios ratio during the frying process. Practical applications: FTIR‐ATR method is very simple, rapid, and environmentally friendly. No sample preparation is required and one drop of oil is enough for FTIR analysis. The proposed method could be applied for quick determination of key fatty acid ratios in the food processing industry.     

Optimization of waste quail eggshells as biocomposites for polyaniline in ammonia gas detection

A simple, cost-effective, and novel chemical sensor for ammonia (NH₃) gas detection was developed from polyaniline (PANI)/quail eggshell (QES) composites. QES is a natural waste enriched in calcium carbonate. In this work, pure PANI was synthesized from chemical oxidation method and PANI/QES composites were prepared from physical mixing of QES with the synthesized PANI at different mass ratio. A series of complementary techniques including Fourier transform infrared and ultraviolet-visible spectrometers, scanning electron microscope with energy dispersive detection coupled with mapping, thermogravimetric analysis, and X-ray diffractometer were used to characterize the physicochemical and textural properties of the biocomposites. From the results, PANI/QES composite with a mass ratio of 1 exhibited the lowest NH₃ detection limit of 5.24 ppm with a linear correlation coefficient (R²) of close to unity (0.9932) between the signal and NH₃ gas concentration. As a whole, the PANI/QES biocomposites synthesized from this work exhibited excellent selectivity toward NH₃ gas even in the presence of other gas impurities, such as acetone, ethanol, and hexane. For the sensor reusability, the PANI/QES biocomposites can be reused in the application of NH₃ gas detection for at least 4 cycles.     

Identification of Pathogenicity-Related Genes in Biofilm-Defective Acidovorax citrulli by Transposon Tn5 Mutagenesis

Biofilm formation is important for virulence of a large number of plant pathogenic bacteria. Indeed, some virulence genes have been found to be involved in the formation of biofilm in bacterial fruit blotch pathogen Acidovorax citrulli. However, some virulent strains of A. citrulli were unable to format biofilm, indicating the complexity between biofilm formation and virulence. In this study, virulence-related genes were identified in the biofilm-defective strain A1 of A. citrulli by using Tn5 insertion, pathogenicity test, and high-efficiency thermal asymmetric interlaced PCR (hiTAIL-PCR). Results from this study indicated that 22 out of the obtained 301 mutants significantly decreased the virulence of strain A1 compared to the wild-type. Furthermore, sequence analysis indicated that the obtained 22 mutants were due to the insertion of Tn5 into eight genes, including Aave 4244 (cation diffusion facilitator family transporter), Aave 4286 (hypothetical protein), Aave 4189 (alpha/beta hydrolase fold), Aave 1911 (IMP dehydrogenase/GMP reductase domain), Aave 4383 (bacterial export proteins, family 1), Aave 4256 (Hsp70 protein), Aave 0003 (histidine kinase, DNA gyrase B, and HSP90-like ATPase), and Aave 2428 (pyridoxal-phosphate dependent enzyme). Furthermore, the growth of mutant Aave 2428 was unaffected and even increased by the change in incubation temperature, NaCl concentration and the pH of the LB broth, indicating that this gene may be directly involved in the bacterial virulence. Overall, the determination of the eight pathogenicity-related genes in strain A1 will be helpful to elucidate the pathogenesis of biofilm-defective A. citrulli.