水口结瘤对板坯连铸结晶器钢水行为影响的数值模拟

以230 mm×1 600 mm板坯连铸机结晶器为研究对象,采用CFD数值模拟的计算方法,建立了VOF模型,研究了连铸水口结瘤对钢渣界面波动与钢液流动行为的影响。研究结果表明,当水口无结瘤时,结晶器内流场为典型的双环流形貌。当水口有结瘤时,结晶器内水口两侧会出现严重的非对称流,结瘤侧流股范围小,非结瘤侧流股范围大。水口不结瘤一侧动能增大导致结晶器下涡心位置下降,会使钢液冲击深度增大;水口结瘤一侧水口因涡心位置较高,加剧了弯月面处的波动和钢渣表面的波动紊乱。结瘤情况下的钢液波动较大,最大波动差为4.03 mm;不结瘤情况下钢液波动较平稳,最大波动差为1.4 mm。     

超声及电磁场对铝合金熔体影响的数值模拟及试验研究

针对铝合金熔体的超声及电磁搅拌处理过程,创建了超声场、电磁场、流场和温度场的数学模型,并采用COMSOL Multiphysics软件求解模型,得到了超声场、电磁场和超声/电磁复合场对铝合金熔体内流场和温度场的分布规律,并通过试验对模拟结果进行了验证。结果表明,增加超声功率使得声压幅值和流场的流动速率均随之增加,同时会使熔体的温度梯度逐渐减小;施加电磁场后产生的电磁搅拌改变了熔体的流动方向且使熔体的流动速率显著增大,这对熔体的温度分布产生了较大影响;在超声和电磁复合场下,电磁场比超声场对熔体流场和温度场的影响更大,且占主导地位。数值模拟结果和试验结果符合较好。     

Superplasticity of fine-grained 7475 Al alloy and a proposed new deformation mechanism

A study has been made to investigate the superplastic deformation mechanisms of 7475 Al alloy in relation to the variation of grain size ranging between 5.5 μm and 13 μm. The strain-rate sensitivity (m) was increased with decreasing grain size in the superplastic deformation regime. Microstructural investigation after tension tests revealed that the dispersoid free zones were produced mostly at the grain boundaries normal to the tensile direction. A new model for describing the deformation behavior of the 7475 Al alloy has been proposed based on the assumption that the grain boundary sliding was accommodated by both diffusional flow and slip. This new model well predicts many aspects of experimental results.     

The form error prediction in side wall machining considering tool deflection

In this research, an effective method for the form error prediction in side wall machining with a flat end mill is suggested. The form error is predicted directly from the tool deflection without surface generation by cutting edge locus with time simulation. The developed model can predict the surface form error accurately about 300 times faster than the previous method. Cutting forces and tool deflection are calculated considering tool geometry, tool setting error and machine tool stiffness. The characteristics and the difference of generated surface shape in up milling and down milling are discussed. The usefulness of the presented method is verified from a set of experiments under various cutting conditions generally used in die and mold manufacturing. This study contributes to real time surface shape estimation and cutting process planning for the improvement of form accuracy.     

中厚板在线30通道超声波探伤方法及应用

介绍了柳钢公司在生产锅炉板、压力容器板过程中，曾试用了６种探伤方法；而研制的３０通道在线超声波探伤法不仅可满足国家标准要求，而且能适应生产节奏，并具有快速、准确、简便的特点。     

A study of tailored blank welding between mild steel sheet and zn-coated steel sheet by CO2 laser beam

Research was conducted on tailored blank welding between mild steel sheet and Zn-coated steel sheet using CO₂ laser beam. The materials used in this study were low carbon steel sheets with a thickness of 1.2 mm and Zn-coated steel sheet with the same thickness and 6.3 μm Zn coating. Experiments were conducted by applying the Taguchi method to obtain optimum conditions for the application of this tailored blank laser welding method in practical manufacturing processes. Optical microscopy, XRD, SEM and TEM analysis were performed to observe the microstructures and to determine the structures of welded zone. In addition, mechanical properties were measured by the microhardness test, tensile test and Erichsen test to evaluate the formability of the welded specimen. There was no trapped Zn in the fusion zone, and the phases of this region consisted of polygonal ferrite, quasi-polygonal ferrite, banitic ferrite and martensite. The elongation value of welded specimen was more than 80% of the value in substrate metal, and the LDH value was more than 90% of the value in substrate metal.     

Microstructure of reactive sintered Al bonded Si3N4-SiC ceramics

Aluminium nitride-silicon nitride-silicon carbide （AIN-Si3N4-SiC） composite ceramics were prepared to increase the bending strength and improve the phase structure of Si3N4-based ceramics. The ceramics were made by reactive sintering in N2 atmosphere at 1 360 ℃, using Al as sintering additive. The phase composing of ceramics was identified with an X-ray diffractometer and the microstructure of the materials was studied by scanning electron microscopy. The results indicate that the phase structure is affected remarkably and the interface modality is changed. The interface between Si3N4 and SiC becomes blurry and that between SiC and AlN matches more better at the same time. But the liquid-phase appears during the reactive sintering along with the addition of AI by which the melting point of Si is decreased. The appearance of liquid Si decreases the bending strength of the ceramics. Lower temperature nitrification technic was introduced to avoid the appearance of liquid-phase Si. The optimum addition of Al was investigated by XRD and SEM analysis in order to obtain the maximal bending strength of materials.     

用于交流自动埋弧焊机的SCR—D调节系统

本文阐述了用SCR-D调节系统代替F-D调节系统的交流自动埋弧焊机的工作原理和电路分析,同时也对该焊机自动引弧提出见解。     

组织状态对循环冲击及非冲击载荷下裂纹扩展的影响

本文对10~#钢和45CrNi合金钢的几种组织状态分别进行了冲击疲劳及非冲击疲劳裂纹扩展试验,结果表明:45CrNi的组织状态对冲击疲劳裂纹扩展的影响较对非冲击疲劳的大;10~#钢的组织状态对两种载荷下的裂纹扩展基本上无影响。结合微观机制和载荷特性,讨论了组织因素对冲击、非冲击疲劳裂纹扩展的影响。