Preparation of TiB2 sintered compacts by hot pressing

A sintered compact of titanium diboride (TiB₂) was prepared by hot pressing of the synthesized TiB₂ powder, which was obtained by a solid-state reaction between TiN and amorphous boron. Densification of the sintered compact occurred at 20 MPa and 1800° C for 5 to 60 min with the aid of a reaction sintering, including the TiB₂ formation reaction between excess 20 at % amorphous boron in the as-synthesized powder (TiB₂ + 0.2B) and intentionally added 10 at % titanium metal. A homogeneous sintered compact of a single phase of TiB₂, which was prepared by hot pressing for 30 min from the starting powder composition [(TiB₂ + 0.2B) + 0.1 Ti], had a fine-grained microstructure composed of TiB₂ grains with diameters of 2 to 3 m. The bulk density was 4.47 g cm^–3, i.e. 98% of the theoretical density. The microhardness, transverse rupture strength and fracture toughness of the TiB₂ sintered compact were 2850 kg mm^–2, 48 kg mm^–2 and 2.4 MN m^–3/2, respectively. The thermal expansion coefficient increased with increasing temperature up to 400° C and had a constant value of 8.8 x 10^–6 deg^–1 above 500° C.     

Reaction control of TiB2 formation from titanium metal and amorphous boron

TiB₂ powder was synthesized by a controlled formation reaction from titanium metal and amorphous boron. Precursory TiB₂ formed by the pretreatment of the mixed powder (mole ratio: B/Ti=2.0) at 600° C for 60 min in an argon stream. Hollow TiB₂ powder with an average grain size of 15m was obtained by subsequent heat treatment above 900° C for more than 60 min in an argon stream. The formation reaction of TiB₂ powder was further controlled by pretreatment of the mixed powder at 600° C for 60 min in a hydrogen and argon stream and subsequent heat treatment at 1000° C for 360 min in an argon stream, when hollow-free TiB₂ powder was formed by a milder formation reaction between amorphous boron and the reformed titanium metal with hydrogen diffused lattice.     

Mechanical property changes in sapphire by nickel ion implantation and their dependence on implantation temperature

Sapphire plates, cut parallel to an {0001} plane, have been implanted with 300 keV nickel ions to doses ranging from 5×10¹² to 1×10¹⁷ Ni cm^–2 at specimen temperatures of 100, 300 and 523 K, in order to investigate the effect of implantation temperature on the mechanical property changes in sapphire caused by ion implantation. The measured changes in surface hardness, surface fracture toughness and bulk flexural strength were found to depend strongly on the implantation temperature, and were largely correlated with the residual surface compressive stress measured by using a cantilever beam technique. The surface amorphization that occurred only by the implantation at 100 K and at doses larger than 2×10s15 Ni cm^–2 reduced the hardness to 0.6 relative to the value of the unimplanted sapphire, and considerably increased the surface plasticity. Furthermore, the amorphization was found to involve a large volume expansion of 30% and to change drastically the apparent shape and size of a Knoop indentation flaw made prior to implantation. This effect was suggested to reduce stress concentrations at surface flaws and hence to increase the flexural strength.     

Development of reel-to-reel microchip mounting system for fabrication of meter-long LED lighting tapes

We have developed a reel-to-reel microchip mounting system that continuously mounts LED chips and other microchips on meter-long flexible printed circuit board (PCB) tape for 1.2-m-long standard LED light tubes. Mounting microchips on meter-long PCBs is difficult because a large chip mounter is expensive and the chip positioning stage is difficult to move in a meter-wide area with an accuracy of hundreds of micrometers. Hence, we developed a new microchip mounting system that utilizes a small chip mounter and reel winding machines. The system repeatedly moves the long PCB tape by a certain length with the reel winding machines and mounts the chips on it. The PCB tape (which is 5 mm wide) is made by fabricating long PCB tapes which are 25 cm × 26.6 m through a roll-to-roll PCB process and slitting them into meter-long tapes. The reel-to-reel system repeatedly mounts chips by adjusting their positions through image processing of the copper wiring pattern on the PCBs. Our constructed system mounted 24 LED chips with a pitch of 5 cm with an accuracy of 0.082 mm to form a 1.2-m-long LED tape. The luminance of the tape is 12.4 lx at a distance of 1 m, which is the luminance of outdoor corridor lighting. Therefore, this system can be used for meter-long tape lighting.     

Two-stage pyrolysis of heavy oils. 3. Pyrolysis of tar-sand bitumens. Relation between ethylene yield and structural characteristics of heavy oils

Thermal cracking of tar-sand bitumens has been carried out using a two-stage pyrolysis reactor with temperature zones of 440°C and 750–800°C, respectively. Feedstocks were pyrolysed in the first stage into cracked oils, which were carried to the second stage for subsequent pyrolysis. Only 12–14 wt% of ethylene was obtained from tar-sand bitumens at the residence time of 1.2 s in the second stage, although 27 and 16 wt% were obtained from Taching and Iranian heavy vacuum residues, respectively. The tar-sand bitumens contain shorter paraffinic straight-chains and have more branched molecules than the vacuum residues of petroleum. A straight-chain paraffin index is proposed, with which a good correlation was obtained between ethylene yield and the fraction of straight-chain paraffin carbons in the heavy oil.     

Reduction of fatty acid hydroperoxides by human parotid saliva

Arachidonic acid hydroperoxide (15-hydroperoxyeicosatetraenoic acid; 15-HPETE) was introduced into human parotid saliva and incubated at 37°C. Straight phase high-performance liquid chromatography analysis of the reaction mixture showed that 15-HPETE was detoxified to its reduced form, 15-hydroxyeicosatetraenoic acid, in the presence of glutathione. Therefore, it is concluded that human parotid saliva possesses fatty acid hydroperoxide-reducing ability. However, its effectiveness was found to be lower than that of blood plasma.     

Investigation of Ozone Loss Rate Influenced by the Surface Material of a Discharge Chamber

Decay characteristics of ozone concentration in oxygen in a chamber with three types of wall material (stainless steel, copper, and aluminum) are measured using the 254 nm photoabsorption method. Effective lifetimes of ozone are estimated from decay curves of ozone concentration. These values depend on the wall material: They are largest for stainless steel and smallest for aluminum. The relationship between effective lifetime and gas pressure is investigated precisely to determine three values. The equivalent diffusion coefficient of ozone in oxygen and the reflection coefficient of ozone at the wall correspond to the loss rate of ozone at the wall. The collisional loss (quenching) rate coefficient of ozone in oxygen is also determined.     

Triterpene alcohols and sterols of Spanish olive oil

Nine Spanish olive oils, including three each of virgin (pressed oil), refined virgin, and B-residue (solvent-extracted pomace oil) oils from different commercial sources, have been analyzed for their unsaponifiable matter (USM). Four sterolic fractions separated from the oils have been analyzed by preparative thin-layer chromatography (TLC); these fractions are triterpene alcohols, 4-methylsterols, sterols and triterpene dialcohols. The compositions of the four sterolic fractions were determined as their acetates by gas-liquid chromatography (GLC) on an OV-17 glass capillary column. Identification of each component was carried out by argentation TLC, GLC and combined gas chromatography-mass spectrometry (GC-MS); 44 components were identified, of which four: 24-methylene-31-nor-9(11)-lanostenol, 24-methyl-31-nor-E-23-dehydrocycloartanol, 24-ethyl-E-23-dehydrolophenol and 5,E-23-stigmastadienol, were considered to be new sterols from natural sources. Several characteristics, including the content of triteterpene dialcohols in the USM and that of C-24(28) unsaturated sterols in each of the four sterolic fractions, which can be used to distinguish between virgin and B-residue olive oils, were observed.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.