Processing and Thermal Conductivity of Sintered Reaction-Bonded Silicon Nitride. I: Effect of Si Powder Characteristics

This paper will present sintered reaction-bonded silicon nitride (SRBSN) material with a high thermal conductivity of 121 W·(m·K)⁻¹, which has been successfully prepared from a coarse Si powder with lower levels of oxygen and aluminum impurities, using a mixture of Y₂O₃ and MgSiN₂ as sintering additives, by nitriding at 1400°C for 8 h and subsequent post-sintering at 1900°C for 12 h at a nitrogen pressure of 1 MPa N₂. This thermal conductivity value is higher than that of the materials prepared from high-purity α-Si₃N₄ powder (UBE SN-E10) with the same additive composition under the same sintering conditions. In order to study the effects of Si powder characteristics on the processing, microstructure, and thermal conductivity of SRBSN, the other type of fine powder with higher native oxygen and metallic impurity (typically Al and Fe) contents was also used. The effects of Si particle size, native oxygen, and metallic impurities on the nitriding process, post-sintering process, and thermal conductivity of the resultant SRBSN materials were discussed in detail. This work demonstrates that the improvement in thermal conductivity of SRBSN could be achieved by using higher purity coarse Si powder with lower levels of oxygen and aluminum impurities. In addition, this work also shows that the nitriding temperature has no significant effect on the microstructure and thermal conductivity of SRBSN during post-sintering, although it does affect the characteristics of RBSN formed during nitridation.     

Studies on the subsite structure of amylases. III. Inhibition by gluconolactone of the hydrolysis of maltodextrin catalyzed by glucoamylase from Rhizopus niveus

Inhibition by gluconic acid-1 : 5-lactone (gluconolactone) and phenyl alpha-glucoside of the hydrolysis of maltodextrin catalyzed by glucoamylase [EC 3.2.1.3] from Rhizopus niveus was investigated in relation to the subsite structure of the enzyme. Inhibition by gluconolactone was of the mixed type, whereas that by phenyl alpha-glucoside was purely competitive. These inhibition types were consistent with a theoretical prediction based on the assumption that gluconolactone and phenyl alpha-glucoside bind mainly to Subsites 1 and 2, respectively. The inhibitor constant of gluconolatone was determined to be 1.5 mM, which is in good agreement with the dissociation constant estimated by difference spectrophotometry (1.5 mM) (Ohnishi, M, et al. (1975) J. Biochem, 77, 695-703).     

Application of a novel polypropylene to the insulation of an electric power cable

Cross‐linked polyethylene (XLPE) has been widely adopted as insulating material for high‐voltage power cables up to 500 kV. Further improvement of electrical and thermal properties on insulating material is required in order to increase cable operation efficiency. Therefore, the development of novel insulating material possessing high thermal properties will be necessary. Recent progress of catalysis technology contributes to obtain new polymeric materials which may be applied to electrical insulation. The authors investigated the basic properties of newly developed stereoregular syndiotactic polypropylene (s‐PP) which is synthesized with homogeneous metallocene catalyst. Though recycling of cross‐linked polymers such as conventionally used XLPE may be difficult because of their poor heat deformation, the s‐PP which is not cross‐linked must be suitable for recycling. A series of experiments on its physical and electrical properties gave the following results.

• (1) s‐PP has sufficient flexibility compared with isotactic polypropylene (i‐PP ).
• (2) Both AC and lightning impulse breakdown strength of s‐PP in spite of no cross‐linking are superior to those of XLPE in the temperature range from 25 to 90 °C.
• (3) Degradation by copper of s‐PP is less than that of i‐PP.
• (4) s‐PP/VLDPE blend shows sufficient brittleness temperature for use.

These results suggested that s‐PP should serve as insulating material for power cables at higher‐temperature operation. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 146(1): 18–26, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002//eej.10210     

Evaluation of TEM samples of an Mg-Al alloy prepared using FIB milling at the operating voltages of 10 kV and 40 kV

Transmission electron microscopy (TEM) samples of an Mg-Al alloy has been prepared using a Ga-focused ion beam (FIB) milling at two different operating voltages of 10 kV and 40 kV to investigate the influence of the FIB energy on the sample quality. The fine structures of the samples have been studied using a high resolution TEM, and the concentration of the implanted Ga was analysed using an energy dispersive X-ray (EDX) analysis. The result of the TEM observation revealed that point defects were introduced to the sample finally milled at 40 kV but not at 10 kV. However, crystal lattice images and electron diffraction patterns were clearly observed on both the samples. The typical influence of the FIB energy was indicated in the elemental analysis. The relative Ga concentration in the thin sample finally milled at 10 kV was 1.0-2.0 at% that is less than half of 4.0-6.0 at% of the Ga concentration in the sample finally milled at 40 kV. A comparison between the experimental results of the Ga concentration measurement with simulation was also discussed.     

Synthesis of Hadamard transformers by use of multimode interference optical waveguides

We propose a synthesis method of optical Hadamard transformer using multimode interference (MMI) couplers. By using the signal transfer matrix of 2 x 2, 4 x 4, and 8 x 8 MMI couplers, we show that sum and difference units of input signals can be synthesized. An interchange unit of two signals can also be synthesized. One synthesis method of Hadamard transformers is a combination of only 2 x 2 units, and the other is a combination of N x N(N > or = 4) units as well as 2 x 2 units. The design examples of operation units are shown, and the size and the output power of Hadamard transformers are estimated.     

Heart instantaneous frequency (HIF): an alternative approach to extract heart rate variability

Our study focuses on a new method of estimating the heart rate variability (HRV) which does not require the use of electrocardiogram (ECG) R-wave detection. Contrary to the R-wave detection method which requires a sampling frequency higher than 100 Hz, the one proposed here can be used to calculate the HRV from an ECG signal sampled at a frequency of approximately 5 Hz with a relative mean error of 0.03. This new method is based on extracting the instantaneous fundamental frequency from the ECG. The method could be efficiently used to extract the HRV from an ECG measured for healthy subjects performing an exercise in which the HRV increases linearly with time, and for subjects with respiratory and cardiac problems. The overall error decreased as we low-pass filtered the HRV with lower cut-off frequencies. Moreover, it was shown that the method could be efficiently used to calculate the HRV from blood pressure measurements and to be robust to noise.     

Multirate Sampling Method for Acceleration Control System

This paper focuses on the realization of high-performance motion control based on acceleration control. A disturbance observer is used to construct an acceleration control system. A high sampling frequency is known to be effective for improving the performance. Characteristics of acceleration control are investigated to discuss the relationship between the performance and a sampling frequency of the system. The needs for a high sampling frequency for an output are then described. Based on these considerations, a novel multirate sampling method for the acceleration control system is proposed. An output sampling period is set shorter than an input sampling period, and control calculation is executed at each output sampling period in the method. The disturbance observer is redesigned for application to the multirate system. Stability analysis is performed to verify the validity of the proposal. Feasibility of the proposed method and its influence on the performance are also verified by experimental results