Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

The flame retardant mechanism of polyolefins modified with chalk and silicone elastomer

This paper presents the current understanding of the flame retardant mechanism of Casico?. The study includes the flame retardant effect of each individual component: ethylene–acrylate copolymer, chalk and silicone elastomer, as well as the formation of an intumescent structure during heating. The flame retardant properties were investigated by cone calorimetry and oxygen index tests. To obtain insight into the flame retardant mechanism, heat treatment under different conditions has also been performed. The results indicate that the flame retardant mechanism of Casico is complex and is related to a number of reactions, e.g. ester pyrolysis of acrylate groups, formation of carbon dioxide by reaction between carboxylic acid and chalk, ionomer formation and formation of an intumescent structure stabilized by a protecting char. Special emphasis is given to the formation of the intumescent structure and its molecular structure as evaluated from ¹³C MAS‐NMR and ²⁹Si MAS‐NMR, ESCA and XRD analysis. After treatment at 500°C the intumescent structure consists mainly of silicon oxides and calcium carbonate and after treatment at 1000°C the intumescent structure consists of calcium silicate, calcium oxide and calcium hydroxide. Copyright © 2003 John Wiley & Sons, Ltd.     

Associative properties of perfluorooctyl end‐functionalized polystyrene–poly(ethylene oxide) diblock copolymers

The synthesis of 2,2,3,3‐tetrahydro‐perfluoroundecanoyl end‐functionalized polystyrene–poly(ethylene oxide) block (PS‐block‐PEO‐R_F) copolymers and their matching PS‐block‐PEO diblock copolymers was carried out by sequential anionic polymerization. Viscometry and ¹⁹F NMR studies show that the PS‐block‐PEO copolymers, in contrast to their matching PS‐block‐PEO‐R_F copolymers, exhibit a micellar rather than the associative behavior seen for the latter. However, the presence of an excess of fluorinated acid, used for end‐functionalization, produces a reduction of the associative behavior above the overlap concentration, with the fluorinated acid acting like a surfactant. A competition may also occur between PS—and R_F—mediated micellization. Copyright © 2004 Society of Chemical Industry     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Breaking the Nyquist barrier

The author discusses the concept that data sampled beyond the Nyquist frequency is meaningless. A simple signal processing scheme to extend resolution to nearly twice the Nyquist without the problem of alias emerged. It starts by placing one-dimensional signals into a simulated sample-and-hold process in a Mathcad application     

Effects of viscosity on the bitterness and astringency of grape seed tannin

To examine the separate effects of viscosity and sweetness on astringency, aqueous solutions of grape seed tannin (GST) were thickened with carboxymethyl cellulose (CMC) from 2 to 45 cP (experiment 1) or sweetened with 0 to 1.8 g/L aspartame (experiment 2). Trained subjects continuously rated astringency and bitterness in duplicate. Subjects were categorized by the salivary flow induced by citric acid and ability to taste n-propyl thiouracil (PROP). In experiment 1, maximum intensity and total duration of astringency were significantly decreased as viscosity rose, although time to maximum intensity of astringency was not affected. Maximum intensity and total duration of bitterness were not significantly affected by increasing viscosity; however, the onset of bitterness was significantly delayed. In experiment 2, increasing sweetness had no affect on any astringency parameter, although maximum intensity of bitterness was significantly decreased. Neither PROP nor salivary flow-status had any effect on perception of bitterness or astringency in either experiment.     

Control-canonical-form method applied to generating systems to improve dynamic stability characteristics

Contents The control-canonical-form (CCF) method is introduced for the purpose of applying it to high-order state-space single-input single or multiple-output (SISO or SIMO) and multiple-input multiple-output (MIMO) linear time-invariant system models to determine closed-loop systems (i.e. design robust controllers) from which enchanced dynamic stability characteristics and overall performance of these systems is achieved. The method has been applied successfully to a SISO 6th-order linearized state-space open-loop model (representing a simplified hydro power system), and to a MIMO 8th-order linearized state-space open-loop model (representing an 87.5 kVA synchronous machine with conventional exciter supplying power to an electric utility system through an interconnection network)

---

Anwendung der kanonischen Form der Zustandsrückführung auf Erzeugersysteme zur Verbesserung der dynamischen Stabilitätseigenschaften

Übersicht Die Methode der kanonischen Form wird auf lineare zeitinvariante Systeme höherer Ordnung im Zustandsraum angewendet, die eine oder mehrere Eingangsgrößen bei einer oder mehreren Ausgangsgrößen aufweisen. Damit werden robuste Regler entworfen, welche die dynamische Stabilität und das gesamte Betriebsverhalten verbessern. Die Methode wurde erfolgreich auf ein linearisiertes Modell sechster Ordnung mit einem Eingang und einem Ausgang angewendet, das vereinfachend eine Wasserkraftanlage darstellt; außerdem auf ein linearisiertes Zustandsmodell achter Ordnung einer Synchronmaschine 87,5kVA mit konventioneller Erregung, die über ein Verbindungsnetzwerk in das öffentliche Netz einspeist.