X-ray Photoelectron Spectroscopy Investigation on the Low-Temperature Degradation of 2 mol% Y2O3-ZrO2 Ceramics

2 mol% Y₂O₃-ZrO₂ polycrystals were annealed in water and under vacuum to highlight the effect of the presence of H₂O on the low-temperature degradation transformation. The specimen surfaces with monoclinic phases transformed during annealing in the different environments were analyzed by X-ray photoelectron spectroscopy with special interest on the electron binding energy change of the constituent ions of the 2 mol% Y₂O₃-ZrO₂ ceramics after the degradation transformation. It was found that no change occurred for the electron-bonding energies of core levels of zirconium ions after the transformation, whereas Y-OH bonds were formed during annealing in water. This result suggested a possibility that the preferred hydration of yttrium took place at the surface of Y₂O₃-partially-stabilized ZrO₂, which is likely to be the reason for the low-temperature degradation accelerated by the presence of H₂O.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Development of a dual‐lamp projector with higher brightness

Stationary projectors mainly used in system applications have recently gained a wider application range, including general presentations in halls and large conference rooms and being used, for example, in digital signage and for monitoring purposes. Consequently, they are required to meet new market demands for durability, reliability, and flexibility in installation in addition to their conventional basic performance such as especially high brightness. To achieve especially high brightness, a new optical system with two lamps is proposed; the profile of the cover glass that prevents the glass from scattering is made aspherical, the profile of the beam‐combining mirror is improved with its position optimized, and the size of the incident plane of the integrator rod is made larger (1.1 times). These measures resulted in an optical system of an even higher efficiency with 7000 lm, which is the highest in its class (according to a June 2010 investigation). Also, the arrangement of two parallel lamps completely eliminated the effect of heat passing from one lamp to the other, which helped secure durability, reliability, and flexibility in installation. Furthermore, the combined use of the unique non‐telecentric optical system, adopted from the conventional single‐lamp model, helps maintain the class‐highest contrast ratio.^1,2     

Humidity Sensor Characteristics of Woodceramics

The humidity sensor characteristics of Woodceramics were investigated. The Woodceramics used in this experiment were prepared at 650–900°C. The size of specimens selected was 1 × 1 × 10 mm . One was used as-cut and the other was polished. Above 700°C, the resistance of the specimen was below 50 and the decrease of resistance with increasing relative humidity was small. The specimen prepared at 650°C had a resistance of about 1 k. The resistance of as-cut specimens decreased with increase in relative humidity, but that of the polished specimen did not change significantly. The difference between as-cut and polished samples was explained by the differences in surface micro-structure.     

Application of the solid polymer electrolyte (SPE) method to organic electrochemistry—III. Kolbe type reactions on Pt-SPE

The feasibility of a solid polymer electrolyte (SPE) method for Kolbe type reactions was investigated by using Pt-SPE composed with Nafion 415 and platinum. The Kolbe reaction of acetic acid proceeded effectively on one side and both sides Pt-SPE composites. The lower current efficiency was observed on the latter than on the former. Neat acetic acid could also be electrolysed on both sides SPE though the cell voltage was fairly high.A methanolic solution of monomethyl adipate was electrolysed to give dimethyl sebacate on both sides Pt-SPE according to the Brown-Walker reaction. The current efficiency and the terminal voltage increased with the concentration of monomethyl adipate. Pt-SPE behaved as an active electrode of a high roughness factor, eg about 6, for the Kolbe reaction of acetate.     

Current transients of passive iron observed during micro-indentation in pH 8.4 borate buffer solution

Micro-indentation test of passive iron electrode in deaerated pH 8.4 borate buffer solution was carried out to investigate the rupture and repair of passive film. During driving a conical diamond micro-indenter with a load of 0.1 N order downward to the electrode and driving upward from the electrode, a couple of anodic current peaks were observed. The first current peak spiked during loading was responsible for partial exposure of iron substrate to the solution due to rupture of the passive film when the indenter tip contacted. The second peak emerged during unloading when elastic deformation recovered, which was ascribed to repair at the ruptured sites. The second peak current was larger than the first one. Both peaks were sensitively influenced by electrode potential or concentration of sulfate ions containing in solution. The model for a series of rupture and repair processes of the passive film by micro-indentation was proposed to discuss the current transients.     

Phase structure in the blend of atactic poly(vinyl alcohol) with atactic poly(vinyl alcohol‐block‐vinyl acetate)

An almost fully saponified atactic poly(vinyl alcohol) and an atactic poly(vinyl alcohol‐block‐vinyl acetate) of which degree of saponification is 89 mol % were blended by a solution casting method. The phase structure of the blend film was analyzed by optical microscopy, ¹³C‐NMR, and differential scanning calorimetry. The most remarkable structure of the blend was composed of cylindrical domains penetrating the film. The swelling behavior of the blend films was also investigated in the dimethylsulfoxide and water mixed solvents to find differences in solubility and diffusion behavior between the matrix and the domain. The cylindrical domains could be selectively dissolved away in water and the film became porous. We tried to change the size of the cylindrical domain with various film preparation conditions. This aimed to turn the film into the useful filter membrane. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1807–1815, 2002