Hot dip fine Zn and Zn-Al alloy double coating for corrosion resistance at coastal area

A new hot dip Zn-7Al alloy coating was performed on a structural steel by double coating of fine Zn and Zn-7 wt.% Al alloy, to prevent severe corrosion in coastal area. The alloy-coated steels were exposed to seaside, quasi-industrial, and rural districts to compare with conventional Zn coating. Double coating was significantly effective in preventing corrosion, particularly in a seaside. It was estimated from the exposure test for 10 years that the life of the Zn-7Al alloy-coated steel would be almost four times that of the Zn-coated steel in the seaside. A bending test showed that no exfoliation occurred at the interface between the coated alloy and substrate steel. TEM observation revealed that the excellent adhesiveness of the doubly coated fine Zn and Zn-7Al alloy to the steel substrate was due to formation of the interface region consisting of heterogeneous fine phase mixture of zinc, aluminium and iron.     

Activity measurements of Al and Cu in Si–Al–Cu melt at 1273 and 1373 K by the equilibration with molten Pb

For the effective control of Al introduction to solidified Si during the solidification refining of Si with the Si–Al-based melt for the solar cell material or the LPE Si film growth processes from the Si–Cu–Al solvent, thermodynamic properties of the Si–Al–Cu melt were investigated at 1273 and 1373 K. Activities of Al and Cu in the Si–Al–Cu melt were measured by the equilibration with molten Pb. Also, the excess Gibbs energy of the melt was studied by the ternary regular solution model.

The evaluated thermodynamic properties of the Si–Al–Cu melt indicated that Cu addition to the Si–Al melt brings the smaller activity coefficient of Al and is effective for reducing the Al content of solidified Si from the melt more effectively than its dilution effect for Al.     

Two‐way multi‐view 2‐D/3‐D display combining LC lens and HVxDP panel using novel pixel arrangement

We have developed a two‐way multi‐view 2‐D/3‐D display combining a liquid crystal lens and horizontally and vertically x times‐density pixels (HVxDP) arrangement. The two‐way multi‐view display features the same display resolution in 2‐D and 3‐D modes and a quite small color moiré for landscape and portrait, respectively, when using the HVxDP arrangement. In this paper, we realized suitable 3‐D properties for achieving a good balance between 3‐D moiré and 3‐D crosstalk for landscape and portrait by a two‐way liquid crystal lens with two kinds of focal lengths for the edge part and the center part of the lens.     

Parallelized fusion visualization system

The speed-up of supercomputers has increased the complexity of simulations. To analyze such kind of data, we believe that new types of visualization software are needed. Therefore, we have been developing a visualization system called “Fusion Visualization”, and the progresses were reported in the AROB 18th and 19th International Symposiums. We introduced the overall concept at the AROB 18th International Symposium, and then demonstrated a sample of flow visualization in a blood vessel in the AROB 19th International Symposium. To extend our system to enable the handling of larger data, we have implemented the proposed system on a parallelized visualization system; AVS/Express PCE (Parallel Cluster Edition). This paper describes the implementation and the benchmark results.     

Time Averaging Algorithms with Stopping Rules for Multi‐Agent Consensus with Noisy Measurements

A time averaging technique is introduced to consensus algorithms in networked multi‐agent systems under a noisy environment. Each agent communicates with its neighboring agents via a constant gain, while the time averaging states of the agents are considered as the values for agreement. The variation of the time averaging states then is evaluated at a specific number of iterations, where the number is given explicitly in terms of parameters related to the consensus accuracy and its probabilistic guarantee. This result establishes a rigorous stopping rule for the multi‐agent consensus with noisy measurements. Several results on this type of stopping rules are provided for undirected, directed, and time‐varying communication graphs. These theoretical results are illustrated through numerical examples.     

Relationship between crystallinity and device characteristics of In‐Sn‐Zn oxide

We have reported that the transistors having the c‐axis‐aligned crystalline (CAAC) In‐Ga‐Zn oxide (IGZO) show good performance. Recently, In‐Sn‐Zn Oxide (ITZO) has attracted much attention because of its high electron mobility, as well as IGZO. However, it has been reported that ITZO field effect transistors (FET) tend to have positive Vth (normally‐on characteristics) and poor reliability compared with IGZO‐FETs. We have reported that high‐performance and high‐reliability OS‐FETs can be fabricated by using CAAC‐IGZO, which has high crystallinity and has no clear grain boundaries, as an active layer. Therefore, we have fabricated CAAC‐ITZO thin films to improve performance of ITZO‐FETs by using CAAC‐ITZO as an active layer. In addition, FETs employing CAAC‐ITZO have better characteristics and reliability than FETs using nano‐crystal ITZO. Furthermore, constant photocurrent method (CPM) measurement was carried out in order to estimate density of deep‐level defect states caused by oxygen vacancies in oxide semiconductors. The results show that CAAC‐ITZO has lower density of deep‐level defect states than nano‐crystal ITZO. We attribute the improvement in reliability of ITZO‐FETs to a decrease in deep‐level defect states of an ITZO active layer, as is the case with IGZO.     

Reversible computing and cellular automata—A survey

Reversible computing is a paradigm where computing models are defined so that they reflect physical reversibility, one of the fundamental microscopic physical property of Nature. In this survey/tutorial paper, we discuss how computation can be carried out in a reversible system, how a universal reversible computer can be constructed by reversible logic elements, and how such logic elements are related to reversible physical phenomena. We shall see that, in reversible systems, computation can often be carried out in a very different manner from conventional (i.e., irreversible) computing systems, and even very simple reversible systems or logic elements have computation- or logical-universality. We discuss these problems based on reversible logic elements/circuits, reversible Turing machines, reversible cellular automata, and some other related models of reversible computing.     

An architecture framework for an adaptive extensible processor

To improve the performance of embedded processors, an effective technique is collapsing critical computation subgraphs as application-specific instruction set extensions and executing them on custom functional units. The problem with this approach is the immense cost and the long times required to design a new processor for each application. As a solution to this issue, we propose an adaptive extensible processor in which custom instructions (CIs) are generated and added after chip-fabrication. To support this feature, custom functional units are replaced by a reconfigurable matrix of functional units (FUs). A systematic quantitative approach is used for determining the appropriate structure of the reconfigurable functional unit (RFU). We also introduce an integrated framework for generating mappable CIs on the RFU. Using this architecture, performance is improved by up to 1.33, with an average improvement of 1.16, compared to a 4-issue in-order RISC processor. By partitioning the configuration memory, detecting similar/subset CIs and merging small CIs, the size of the configuration memory is reduced by 40%.     

Current control of a PWM power amplifier by an approximate 2-degree-of-freedom digital controller

There is a need for robust current control of a pulse width modulation (PWM) power amplifier whose transient response characteristics do not deteriorate with extensive load changes and/or direct-current power supply voltage changes. In this article, we propose a digital robust controller with bumpless mode switching to control the current of a PWM power amplifier to satisfy the demands and extend the range of an inductive load width. It is necessary to measure the value of the load in order to implement this bumpless mode switching automatically depending on the load range. Therefore, a method of estimating the inductive load is shown. The bumpless mode switching is automatically performed by estimating an inductive value without specifying the value of the inductive load beforehand. That is, the value of the inductive load is estimated during the DDC execution, and the control mode is automatically switched bumplessly according to this estimated value. A digital controller equipped with inductance estimation and bumpless mode switching is realized by a DSP. Some experiments show that the digital controller with the proposed bumpless mode switching can satisfy larger specifications.