Comparisons of PWM and one-cycle control for power amplifier with multilevel converter

Based on the concepts of cascade multilevel converters and one-cycle technique, comparisons are conducted to characterize the distortion of the pulsewidth modulation (PWM) and one-cycle control methods that were applied to converters. Simulation results for the different control schemes are obtained in PSIM software initially to see the effect of one-cycle control different from that of PWM control. Through the comparisons, the advantages and disadvantages are identified for each method. The one-cycle scheme is better than PWM control in reducing undesirable harmonics and tracing dynamic waveforms. Simulation and experimental results are also provided to verify the conclusions.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

An overview of electric vehicle technology

An overview of the present status and future trends in electric vehicle technology is provided. The emphasis is on the impact of rapid development of electric motors, power electronics, microelectronics, and new materials. Comparisons are made among various electric drive systems and battery systems. The market size of electric vehicles in the coming years and the potential electric vehicle impacts are discussed     

Mechanism of iodine vapor sorption in polyacetylene

Simultaneous measurements of weight uptake and conductivity variation during iodine vapor sorption of polyacetylenes (PA) at 20–25°C show that the sorption is a two-stages process. For the first stage, iodine diffusion to the fibrilar surface of the cis-rich and trans-rich PA is of Knudsen type pore diffusion as supported by the sorption measurements of hexane for the cis-rich PA, and has a diffusion coefficient in the order of 10⁷ cm²/sec. Conductivity of the PA rises rapidly and reaches a maximum at end of the stage. For the second stage, the diffusion is more restrictive and has a diffusion coefficient lower than the first stage by a factor of about 10 due to multilayer sorption of iodine, which leads to a decrease in the pore diameter and therefor the diffusion rate. In addition to the restricted diffusion in the second stage, diffusion of the iodine molecules adsorped on the fibrilar surface into the interior of the fibrils is appreciable for cis-rich PA (leading to a conductivity drop) and is negliglible for tran-rich PA (leading to insignificant variation in conductivity).     

Advanced concepts in electric vehicle design

In 1994, the Eco-Vehicle Project was begun to develop an electric vehicle (EV) using a ground-up design approach that incorporates unique designs specific to an EV. The Eco-Vehicle will be a high-performance, but ultrasmall, battery-powered vehicle. New designs for the Eco-Vehicle include an in-wheel motor drive system, a hollow load floor which will house the batteries, and a new battery management system. The Eco-Vehicle may also utilize other advanced concepts suitable especially for EVs, including solar panels for battery charging and intelligent crash avoidance and guidance systems     

试谈我国紫菜资源的工业利用

介绍了我国紫菜工业在工艺改进、资源开发、综合利用和深度加工等方面的情况,提出了提高产率、降低物耗、增进效益和增加品种的途径。     

Ultrathin oxide-nitride dielectrics for rugged stacked DRAMcapacitors

Ultrathin dielectric materials that provide high capacitance values are needed for 64- and 256-Mb stacked DRAMs. It is shown that capacitance values as high as 12.3 fF/μm² can be obtained with ultrathin nitride-based layers deposited on rugged polysilicon storage electrodes. These films present the reliability and low leakage current levels required for 3.3-V applications. The nitride thickness, however, cannot be scaled much below 6 nm to avoid the oxidation-punchthrough mechanisms that appear when too-thin films are unable to withstand the reoxidation step     

Generalized impedance control of robot for assembly tasks requiringcompliant manipulation

To perform assembly tasks requiring compliant manipulation, the robot must follow a motion trajectory and exert an appropriate force profile while making compliant contact with a dynamic environment. For this purpose, a generalized impedance in the task space consisting of a second-order function relating the motion errors and interaction force errors is introduced such that the contact force can be commanded and controlled. With generalized impedance control, the robot can behave with a desired dynamic characteristic when it interacts with the environment. To ensure the success of the assembly, a strategy during task planning which takes into consideration the interrelation between motion and force trajectories as well as contact compliance is introduced. The generalized impedance control method is applied to the prismatic joint of a selective compliance assembly robot arm (SCARA) robot for inserting a printed circuit board (PCB) into an edge connector socket. Depending on the progress of the parts joining operation, various amount of interaction forces are generated which have to be accommodated. It is demonstrated that an assembly strategy which consists of a sequence of carefully planned target impedance can enable the task to be executed in a desirable manner. The effectiveness of this approach is illustrated through experiments by comparing the results with those obtained using a well-established position control scheme as well as the original impedance control method     

Effects of Stearic Acid on the Injection Molding of Alumina

This research investigated the influence of stearic acid on the injection molding of alumina, by varying the concentration of stearic acid. The interaction between stearic acid and alumina was identified using transmission infrared spectroscopy, indicating stearic acid preferentially adsorbed onto the alumina powder surface. In addition to slightly modifying the intrinsic binder viscosity, stearic acid adsorbed onto the powder surface changed the flow behavior of the mixtures from dilatant flow to pseudoplastic flow at low temperatures. As a result, inhomogeneous distribution of binder in the injection-molded parts was minimized with increased stearic acid concentration. However, the possibility of forming bubbles in the mixtures arising from vaporization of stearic acid was enhanced. Additionally, the binder burnout temperature range was broadened with the increase of stearic acid concentration.