Silica-supported cobalt catalysts for the selective reduction of nitrogen monoxide with propene

Catalytic behavior of silica-supported transition metals for NO reduction with propene in the presence of oxygen was investigated. While both silica and cobalt oxides did not show any activity for the selective NO reduction, impregnated CoO/SiO₂ prepared from cobalt acetate showed good activity although the preparation conditions had significant effect on the activity. It was suggested that highly dispersed surface Co²⁺ ions on silica are responsible for the catalytic activity.     

Direct Ink Writing of a Preceramic Polymer and Fillers to Produce Hardystonite (Ca2ZnSi2O7) Bioceramic Scaffolds

The direct ink writing of an ink composed of a preceramic polymer and fillers was used to produce hardystonite (Ca₂ZnSi₂O₇) bioceramic scaffolds. Suitable formulations were developed for the extrusion of fine filaments (350 μm diameter) through a nozzle. The preceramic polymer was employed with the double purpose of contributing to the rheology of the ink by increasing its viscosity and of forming the hardystonite phase upon heat treatment by reacting with the fillers. A control of the rheology is essential when spanning features have to be produced, and therefore the main rheological characteristics of the inks were measured (flow curves, dynamic oscillation tests, viscosity recovery tests) and compared to models reported in the literature. Highly porous scaffolds (up to 80% total porosity) were produced and heat treated in air or in nitrogen atmosphere. The influence of the heat‐treatment atmosphere on the morphology, crystalline phase assemblage, and compressive strength of the scaffolds was investigated.     

Reduced Thermal Budget Process for SBT Thin Film in Planer Type Stack Cell FeRAMs

In order to reduce the thermal budget for SBT crystallization process in planer type stack cell FeRAMs, Rapid Thermal Anneal (RTA) based process for SBT thin film was investigated. Our new process is characterized by crystallization in RTA without any furnace annealing process, and includes a low temperature recovery annealing process (hereafter RTB (Reduced Thermal Budget) process). As a result of only 750C RTA for accumulated time of 60s without furnace annealing process, the sufficient ferroelectric properties were derived in comparison with that of conventional SBT thin film. In the RTB process, two approaches to improve the break down voltage were carried out. First, we used UV exposure during the baking process. By optimizing the UV assisted baking process, a high break down field due to smooth surface morphology was successfully obtained, resulting in break down field of more than 1.2 MV/cm. Secondly, ultra thin SBT films as a top few layer on the base SBT thin film were employed. After optimization of the ultra thin SBT layer thickness, a very smooth SBT surface was successfully achieved, resulting in improvement of the break down field of more than 1.1 MV/cm.     

Asymmetric Hydrogenation of 3‐Amido‐2‐arylpyridinium Salts by Triply Chloride‐Bridged Dinuclear Iridium Complexes Bearing Enantiopure Diphosphine Ligands: Synthesis of Neurokinin‐1 Receptor Antagonist Derivatives

We describe a most straightforward synthetic method for preparing neurokinin‐1 (NK1) receptor antagonist derivatives by asymmetric hydrogenation of 3‐amido‐2‐arylpyridinium salts using dinuclear iridium complexes with enantiopure diphosphine ligands, affording the corresponding chiral piperidines in high cis‐diastereoselectivity (>95:5) and moderately high enantioselectivity (up to 86%). Deprotection treatments afforded the NK‐1 receptor antagonist (+)‐CP‐99,994 (83% ee). In addition, we observed unique additive effects of 10‐camphorsulfonic acid in the asymmetric hydrogenation of 3‐amido‐2‐arylpyridinium salts.

     

Compatibilization of recycled poly(ethylene terephthalate) and polypropylene blends: Effect of polypropylene molecular weight on homogeneity and compatibility

The effectiveness of compatibilizers in enhancing the dispersion of polypropylene (PP) at various molecular weights in recycled polyethylene terephthalate (RPET) was elucidated. The idea of incorporating PP of different molecular weights evolved from the intention of simultaneously recycling the PET bottles together with the PP‐based bottle caps, which are often of low molecular weight (M_w). Three grades of PP with known molecular weights were blended with RPET at various loadings of compatibilizers. Morphological analyses suggest that the dispersion of the PP particles was more homogeneous, and the average particle size was smaller when low M_w PP was incorporated. This indicates that the interaction between the compatibilizer and PP particles was more intense with the presence of a large number but shorter PP molecular chains. Moreover, specimens containing low M_w PP were found to remain homogeneous regardless of compatibilizer and PP content in the RPET/PP blends. The homogeneity of the blends significantly affected their mechanical performance as well. Higher stiffness, yield strength, deformability, and toughness were observed when low M_w PP was incorporated, regardless of PP and compatibilizer loadings. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

New integral experiments for large angle scattering cross section data benchmarking with DT neutron beam at JAEA/FNS

A new integral experiment with a deuteron–triton fusion (DT) neutron beam started in order to validate scattering cross section data. First the DT neutron beam was constructed with a collimator. The performance of the collimator system and the characteristics of the DT neutron beam were measured. Second a new integral experiment for type 316 stainless steel (SS316) was carried out with this DT neutron beam. The DT neutron beam of 3.5 cm in diameter was injected to the front surface center of an SS316 cylindrical assembly. Reaction rates of the ⁹³Nb(n,2n)^92mNb reaction in the assembly were measured with the activation foil method and were calculated with the Monte Carlo transport calculation code. The measurement points were located at three positions, on the center of the beam axis and at 15 cm and 30 cm apart from the axis. The ratio of calculation to experiment of the ⁹³Nb(n,2n)^92mNb reaction rate became smaller than 1 with the distance from the beam axis. Then, the dependency of each reaction rate on scattering angle was calculated. It was proved that at off-axis positions, where C/E is smaller than 1, 90° scattering contribute relatively larger than at on-axis positions and backward scattering made little contribution to the results in this experiment. The reasons of the discrepancy between the measured and calculated data will be investigated.     

Dynamic defocus and occlusion compensation of projected imagery by model-based optimal projector selection in multi-projection environment

This paper presents a novel model-based approach of dynamic defocus and occlusion compensation method in a multi-projection environment. Conventional defocus compensation research applies appearance-based method, which needs a point spread function (PSF) calibration when either position or orientation of an object to be projected is changed, thus cannot be applied to interactive applications in which the object dynamically moves. On the other hand, we propose a model-based method in which PSF and geometric calibrations are required only once in advance, and projector’s PSF is computed online based on geometric relationship between the projector and the object without any additional calibrations. We propose to distinguish the oblique blur (loss of high-spatial-frequency components according to the incidence angle of the projection light) from the defocus blur and to introduce it to the PSF computation. For each part of the object surfaces, we select an optimal projector that preserves the largest amount of high-spatial-frequency components of the original image to realize defocus-free projection. The geometric relationship can also be used to eliminate the cast shadows of the projection images in multi-projection environment. Our method is particularly useful in the interactive systems because the movement of the object (consequently geometric relationship between each projector and the object) is usually measured by an attached tracking sensor. This paper describes details about the proposed approach and a prototype implementation. We performed two proof-of-concept experiments to show the feasibility of our approach.     

Estimating life-form cover fractions in California sage scrub communities using multispectral remote sensing

The California sage scrub (CSS) community type in California's Mediterranean-type ecosystems is known for its high biodiversity and is home to a large number of rare, threatened, and endangered species. Because of extensive urban development in the past fifty years, this ecologically significant community type is highly degraded and fragmented. To conserve endangered CSS communities, monitoring internal conditions of communities is as crucial as monitoring distributions of the community type in the region. Vegetation type mapping and field sampling of individual plants provide ecologically meaningful information about CSS communities such as spatial distribution and species compositions, respectively. However, both approaches only provide spatially comprehensive information but no information about internal conditions or vice versa. Therefore, there is a need for monitoring variables which fill the information gap between vegetation type maps and field-based data. A number of field-based studies indicate that life-form fractional cover is an effective indicator of CSS community health and habitat quality for CSS-obligated species. This study investigates the effectiveness of remote sensing approaches for estimating fractional cover of true shrub, subshrub, herb, and bare ground in CSS communities of southern California. Combinations of four types of multispectral imagery ranging from 0.15 m resolution scanned color infrared aerial photography to 10 m resolution SPOT 5 multispectral imagery and three image processing models - per-pixel, object-based, and spectral mixture models - were tested.An object-based image analysis (OBIA) routine consistently yielded higher accuracy than other image processing methods for estimating all cover types. Life-form cover was reliably predicted, with error magnitudes as low as 2%. Subshrub and herb cover types required finer spatial resolution imagery for more accurate predictions than true shrub and bare ground types. Positioning of sampling grids had a substantial impact on the reliability of accuracy assessment, particularly for cover estimates predicted using multiple endmember spectral mixture analysis (MESMA) applied to SPOT imagery. Of the approaches tested in this study, OBIA using pansharpened QuickBird imagery is one of the most promising approaches because of its high accuracy and processing efficiency and should be tested for more heterogeneous CSS landscapes. MESMA applied to SPOT imagery should also be examined for effectiveness in estimating factional cover over more extensive habitat areas because of its low data cost and potential for conducting retrospective studies of vegetation community conditions.     

Optimization of facial skin temperature-based anomaly detection model considering diurnal variation

Artificial Life and Robotics - The amount of blood under the surface of skin is controlled by the autonomic nervous system and directly influences the facial skin temperature. Classification models...     

An Intents-based approach for dynamic service discovery

Service discovery has been a very active research field attracting many researchers around the world. Most of the previous research efforts on service discovery have been based on the ternary classification of participant roles in web services, including service providers, brokers, and consumers. This classification is insufficient because it fails to make a difference between application developers and end users who both belong to service consumers. As a result, application developers usually take the responsibility of seeking services while end users who ultimately use the application are ignored. In order to address this issue, this paper presents an Intents-based approach for dynamic service discovery. The proposed approach is motivated from two industrial protocols: Android Intents and web Intents. It improves the two protocols by a generic model from the aspects of architecture, intent messages and their resolving process, Intents services, and user agents. It classifies the implicit intents into authoritative and naïve intents and is compatible with the current web service triangular architecture. This paper also illustrates a way of creating Intents services from SOAP and REST web services and presents two cases to demonstrate some benefits of the proposed approach.