Dependence of Seebeck coefficient on a load resistance and energy conversion efficiency in a thermoelectric composite

The thermo-emf ΔV and current ΔI generated by imposing the alternating temperature gradients (ATG) at a period of T and the steady temperature gradient (STG) on a thermoelectric (TE) composite were measured as a function of t, where t is the lapsed time and T was varied from 60 to or ∞ s. The STG and ATG were produced by imposing steadily and alternatively a source voltage V in the range from 1.0 to 4.0 V on two Peltier modules sandwiching a composite. ΔT, ΔV, ΔI and V_P oscillate at a period T and their waveforms vary significantly with a change of T, where ΔV and V_P are the voltage drops in a load resistance R_L and in resistance R_P of two modules. The resultant Seebeck coefficient |α| = |ΔV|/ΔT of a composite under the STG was found to be expressed as |α| = |α₀|(1 − R_comp/R_T), where R_T is the total resistance of a circuit for measuring the output signals and R_comp is the resistance of a composite. The effective generating power ΔW_eff has a local maximum at T = 960 s for the p-type composite and at T = 480 s for the n-type one. The maximum energy conversion efficiency η of the p- and n-type composites under the ATG produced by imposing a voltage of 4.0 V at an optimum period were 0.22 and 0.23% at ΔT_eff = 50 K, respectively, which are 42 and 43% higher than those at ΔT = 42 K under the STG. These maximum η for a TE composite sandwiched between two Peltier modules, were found to be expressed theoretically in terms of R_P, R_T, R_L, α_P and α, where α_P and α are the resultant Seebeck coefficients of Peltier modules and a TE composite.     

A low-carbon scenario creation method for a local-scale economy and its application in Kyoto city

On May 2008, Kyoto city government set up a low-carbon target of a 50% GHG reduction by 2030 compared to the 1990 level. To contribute to these discussions, we developed a local (city-scale) low-carbon scenario creation method. An estimation model was developed to show a quantitative and consistent future snapshot. The model can explicitly treat the uncertainty of future socio-economic situations, which originate from the openness of local economy. The method was applied to Kyoto city, and countermeasures to achieve the low-carbon target were identified. Without countermeasures, emissions would increase 12% from 2000. Among the measures, the reduction potential of energy efficiency improvements to residential and commercial sectors was found to be relatively large (15% and 18% of total reductions, respectively). The reduction potential of the passenger transport sector, in which the city government's policy is especially important, was 17% of the total amount. A sensitivity analysis showed that a 10% increase in exports leads to an 8.5% increase in CO₂ emissions, and a 20% increase in the share of the commuters from outside the city leads to a 3.5% decrease of CO₂ emissions because of the smaller number of residents in the city.     

Heavy oxynitridation technology for forming highly reliable flash-type EEPROM tunnel oxide films

For the first time, it is demonstrated that in flash-type EEPROMs, the endurance properties are dramatically improved by heavy oxynitridation (RTONO) of the tunnel oxide. The layer composition evaluated by SIMS measurement indicates that large amounts of N atoms (>10/sup 20/ atom/cm/sup 3/) pile up at the SiO/sub 2/-Si interface, and are distributed in the bulk SiO/sub 2/. In addition, the RTONO film reduces the number of hydrogen atoms, which are the origin of electron traps. This oxynitridation causes a decrease of both electron and hole traps in the tunnel oxide, resulting in an improvement of the threshold voltage narrowing.<>     

A study on the characteristics of glass fibre reinforced thermoplastics by transfer moulding

Lately, the use of fibre reinforced thermoplastics (FRTP) has increased due to its increased mouldability compared to thermosetting FRP material.

FRTP includes stampable sheet, short and long fibre reinforced thermoplastic pellets, continuous fibre reinforced thermoplastics sheets, etc. The long fibre reinforced thermoplastic (LFRTP) pellet has better mechanical properties than short fibre reinforced pellets and better mouldability than stampable sheet. At present, injection moulding method is mainly used for moulding LFRTP pellets because of its high productivity.

However, the long fibre of LFRTP pellets, whose length is the same as pellet length, is degraded during processing if conventional injection moulding machines are used, and as a result, the mechanical properties are not improved as expected in many cases. Therefore, a new moulding process is required to make good use of LFRTP pellets.

For this study, a transfer moulding apparatus was designed and built to minimize fibre degradation of the moulded parts.

Firstly, the LFRTP pellets with fibre lengths of 3, 6, 9, 12.7 and 17 mm were prepared in order to clarify the difference of mechanical properties due to fibre length. The fibre ratio was 30% in weight for all cases and the same polypropylene was used. They were moulded to the shape of the test specimens. Tensile, bending and Izod impact strengths were measured by using these test specimens. Secondly, LFRTP pellets were moulded to the shape of test specimens by the transfer moulding apparatus and conventional injection moulding machine, and then mechanical properties were measured. At the same time, short fibre pellets were moulded to the smae shape of test specimens by the injection moulding machine, and mechanical properties were compared with those of LFRTP pellets.

With the long glass fibre reinforced polypropylene, good results of fibre preservation and mechanical properties were obtained by the transfer moulding apparatus which was built for this study. The impact strength was increased remarkably as the fibre length increased, and consequently the preservation of fibre length in the moulded parts was especially effective in improving the impact strength.     

Environmental ecological modeling of human blood lead levels in East Asia

Environmental ecological modeling (EEM), which unifies models simulating transport of chemicals and exposure of humans to chemicals, was used to simulate long-term trends of female adult human blood lead levels (BLLs) and historical exposure to the atmospheric lead in four East Asian countries: Japan, Korea, China, and Vietnam. Anthropogenic lead emissions to the atmosphere in Vietnam were estimated from energy statistics to be 1931 t yr(-1). Calculated BLLs generally agreed with those observed in samples collected in these countries as the error factors were less than 2. The model results revealed that BLLs decreased significantly in Tokyo (by 58%) and Seoul (by 45%) in recent decades and confirmed the effects of efforts to reduce environmental lead in Japan and Korea. The model results also revealed that BLLs in Beijing did not decrease in this decade as much as in Tokyo and Seoul, despite the phasing out of leaded gasoline, and that the contribution from the atmospheric component was increasing (43% in 2009). Finally, we applied EEM to simulate BLLs of children in Hanoi. The probability of children having BLLs greater than 50 μg L(-1) was 7.5%, which was greater than those observed in developed countries.     

A quadruple-scanning-probe force microscope for electrical property measurements of microscopic materials

Four-terminal electrical measurement is realized on a microscopic structure in air, without a lithographic process, using a home-built quadruple-scanning-probe force microscope (QSPFM). The QSPFM has four probes whose positions are individually controlled by obtaining images of a sample in the manner of atomic force microscopy (AFM), and uses the probes as contacting electrodes for electrical measurements. A specially arranged tuning fork probe (TFP) is used as a self-detection force sensor to operate each probe in a frequency modulation AFM mode, resulting in simultaneous imaging of the same microscopic feature on an insulator using the four TFPs. Four-terminal electrical measurement is then demonstrated in air by placing each probe electrode in contact with a graphene flake exfoliated on a silicon dioxide film, and the sheet resistance of the flake is measured by the van der Pauw method. The present work shows that the QSPFM has the potential to measure the intrinsic electrical properties of a wide range of microscopic materials in situ without electrode fabrication.     

Effect of CO2 on layered Li1+zNi1−x−yCoxMyO2 (M = Al,Mn) cathode materials for lithium ion batteries

We investigated the effect of CO₂ on layered Li_1+zNi_1−x−yCo_xM_yO₂ (M = Al, Mn) cathode materials for lithium ion batteries which were prepared by solid-state reactions. Li_1+zNi_(1−x)/2Co_xMn_(1−x)/2O₂ (Ni/Mn mole ratio = 1) singularly exhibited high storage stability. On the other hand, Li_1+zNi_0.80Co_0.15Al_0.05O₂ samples were very unstable due to CO₂ absorption. XPS and XRD measurements showed the reduction of Ni³⁺ to Ni²⁺ and the formation of Li₂CO₃ for Li_1+zNi_0.80Co_0.15Al_0.05O₂ samples after CO₂ exposure. SEM images also indicated that the surfaces of CO₂-treated samples were covered with passivation films, which may contain Li₂CO₃. The relationship between CO₂-exposure time and CO₃²⁻ content suggests that there are two steps in the carbonation reactions; the first step occurs with the excess Li components, Li₂O for example, and the second with LiNi_0.80Co_0.15Al_0.05O₂ itself. It is well consistent with the fact that the discharge capacity was not decreased and the capacity retention was improved until the excess lithium is consumed and then fast deterioration occurred.     

Silent myocardial ischemia in Kawasaki disease: evaluation of percutaneous transluminal coronary angioplasty by dobutamine stress testing

BACKGROUND: Myocardial ischemia and myocardial infarction are the most serious complications of coronary artery lesions in children with Kawasaki disease (KD). Therefore, early detection and treatment of myocardial ischemia in patients with KD is essential. We studied the effectiveness of percutaneous transluminal coronary angioplasty (PTCA) in patients with silent myocardial ischemia detected by dobutamine stress 99mTc myocardial scintigraphy (TMS), body surface mapping (BMS), and signal-averaged ECG late potentials (ELP). METHODS AND RESULTS: Eight of 76 asymptomatic patients with a coronary stenosis >25% and a positive dobutamine stress test were considered to have silent myocardial ischemia. All eight patients had >95% stenoses demonstrated by coronary angiography (CAG) just before PTCA. After PTCA, CAG showed that all of the coronary artery stenoses had been reduced to <50%. Additionally, intravascular ultrasonography (IVUS) performed in five patients before and after PTCA demonstrated adequate dilation of the coronary stenosis after PTCA. All eight patients underwent dobutamine stress TMS, BMS, and ELP 2 to 3 months after PTCA, which demonstrated no regions of myocardial ischemia. Approximately 6 months later, CAG was performed in all eight patients, and only one patient had developed restenosis. CONCLUSIONS: PTCA effectively dilates stenotic coronary arteries in children with KD. Moreover, dobutamine stress TMS, BMS, and ELP are useful for detecting silent myocardial ischemia and estimating the effectiveness of PTCA. Furthermore, IVUS is useful for evaluating the severity of coronary artery lesions before and after PTCA in patients with KD.