Experimental determination of the overall heat loss coefficient for energy requirement of greenhouse heating

This paper presents an experimental determination of energy requirement for greenhouse heating. The overall heat loss coefficient, heat input, the control factor for air‐tightness, the rate of heat loss and the thermal screen effectiveness were calculated. The relationships between the overall heat loss coefficient and the wind speed, and the outside temperature were modelled, including the measured and calculated values. It was found that the thermal screen effectiveness was 16 and 19.8% for the polyethylene (PE) and polyester screens, respectively. Copyright © 2005 John Wiley & Sons, Ltd.     

The performance of ceramic and cermet cutting tools for the machining of austempered ductile iron

In this study, the machinability of austempered ductile iron (ADI) having a ferritic structure was examined. For this purpose, three types of ductile iron materials (as cast, ADI-250, ADI-375) and two different types of cutting tool materials (ceramics and cermet) were used. To emphasize the role of austempering process, ductile iron (DI) specimens are first austenitized in salt bath at 900°C for 120 minutes after which they are quenched in salt bath at 250°C (ADI-250) and 375°C (ADI-375) for 120 min. Machining tests were carried out at various cutting speeds (100–500 m/min) under the constant depth of cut and feed rate. The performance of both ceramic and cermet tools were evaluated based on the workpiece surface roughness and flank wear. Wear conditions of the cutting tools were characterized by scanning electron microscope. The results point out that the lower austempering temperature results in increasing of the cutting forces, while better surface roughness is obtained. Additionally, the results indicate that the tool wear occurs mainly on the flank face. However, higher cutting speed results in chipping formation in cermet cutting tool.     

Fabrication and characterization of anisotropic dielectrics for low-loss microwave applications

New magneto-photonic assembly designs for high-gain antennas require dielectrics with a significant anisotropy and low loss at GHz frequencies. This paper describes an approach to fabricate such dielectrics from ceramic laminates. These laminates consist of two ceramics with largely different permittivities and low dielectric losses. Alternating layers of commercially available α-Al₂O₃ and Nd-doped BaTiO₃ were laminated using organic adhesives. Equivalent permittivity tensors and loss tangents were characterized using a resonant cavity-based approach, which was coupled with a finite-element method full-wave solver. Measured permittivity values were in good agreement with mean field predictions; a minimum loss tangent 1.1 × 10^?3 was obtained when using one-component epoxy (Loctite^®-3982) adhesive. Application of two-component epoxy (M-bond 610) adhesive results in a slightly higher loss but better mechanical properties and machinability. These laminates were used to demonstrate high gain in a prototype antenna with 6 misaligned anisotropic dielectric layers.     

Synthesis and Characterization of a Bis-Pyrazoline Derivative as Corrosion Inhibitor for A283 Carbon Steel in 1M HCl: Electrochemical,Surface, DFT and MD Simulation Studies

Protection of Metals and Physical Chemistry of Surfaces - The effect of a new synthesized bis-pyrazoline derivative namely: 5,5'-(1,4-phenylene) bis [1?formyl-4,5-dihydro-3-phenyl-1H...     

Improving hydrophobicity on polyurethane-based synthetic leather through plasma polymerization for easy care effect

This study reports on the deposition of a hydrophobic coating on polyurethane (PU)-based synthetic leather through a plasma polymerization method and investigates the hydrophobic behavior of the plasma-coated substrate. The silicon compound of hexamethyldisiloxane (HMDSO), inactive gas argon (Ar), and toluene were used to impart surface hydrophobicity to a PU-based substrate. Surface hydrophobicity was analyzed by water contact angle measurements. Surface hydrophobicity was increased by deposition of compositions of 100% HMDSO, 3:1 HMDSO/toluene, and 1:1 HMDSO/toluene. Optimum conditions of 40 W, 30 s plasma treatment resulted in essentially the same initial contact angle results of approximately 100° for all three treatment compositions. The initial water contact angle for untreated material was about 73°. A water droplet took 1800 s to spread out on the plasma-treated sample after it had been placed on the sample surface. An increase in plasma power also led to a decrease in contact angle, which may be attributed to oxidization of HMDSO during plasma deposition. XPS analysis showed that plasma polymerization of HMDSO/toluene compositions led to a significant increase in atomic percentage of Si compound responsible for the hydrophobic surface. The easy clean results for the treated and untreated PU-based synthetic leather samples clearly showed that the remaining stain on the plasma-polymerized sample was less than that of untreated sample. The plasma-formed coating was both hydrophobic and formed a physical barrier against water and stain.     

Evaluation of deflection amplification factor in steel moment‐resisting frames

Steel moment‐resisting frames (SMRFs) are the most common type of structural systems used in steel structures. The first step of structural design for SMRFs starts with the selection of the structural sections on the basis of story drift limitation. ASCE 7 (2010) requires that the inelastic story drifts be obtained by multiplying the deflections determined by elastic analysis under design earthquake forces with a deflection amplification factor (C_d). For special moment‐resisting frames, C_d is given as 5.5 in ASCE 7 (2010). Lower C_d values will increase the overall inelastic response of the structure. On the other hand, the inelastic response of the structure is expected to be less severe when designed for higher C_d values. The performance objective is that the structure should sustain the inelastic deformation demand imposed due to design earthquake ground motions. This study aims at investigating the inelastic seismic response that low‐rise, medium‐rise and high‐rise SMRFs can experience under design earthquake ground motions and maximum considered earthquake (MCE) level ground motions and evaluating the deflection amplification factors (C_d) for SMRFs in a rational way. For this purpose, nonlinear dynamic time history and pushover analyses will be carried out on SMRFs with 4, 9 and 20 stories. The results indicate that the current practice for computing the inelastic story drifts for SMRFs is rational and the frames designed complying with the current code requirements can sustain the inelastic deformations imposed during design earthquake ground motions when seismically designed and detailed. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of different boron precursors on superconducting and mechanical properties of MgB2

The superconducting, structural and mechanical properties of MgB₂ bulk samples have been studied as a function of precursor B powder particle size by means of AC susceptibility, XRD and microhardness measurements, respectively. The in situ processed MgB₂ samples have been prepared by means of conventional solid state reaction method with magnesium powder (99.8 %, 325 mesh) and four different types of boron powders (95.2, >95, 91.9 and 86.7 %) from two sources, Pavezyum and Sigma Aldrich. The XRD measurements showed that the diffraction peaks for our samples belong to the main phase of the MgB₂ diffraction patterns. The highest critical temperature T _c = 37.7 K was achieved for the MgB₂ sample which was fabricated by using >95 % purity amorphous boron. Microhardness measurements were performed to investigate the mechanical properties. Load independent hardness, Vickers microhardness, Young’s modulus, fracture toughness, and yield strength values were calculated separately for all samples. The results were analyzed by using the Meyer’s law, proportional sample resistance model, elastic–plastic deformation model, Hays Kendall approach, and indentation induced cracking (IIC) model. It was found that the IIC model is the most successful model to describe the mechanical properties of our samples.     

An artificial neural network model for virtual Superpave asphalt mixture design

This study presents an artificial neural network (ANN) model to predict the asphalt mixture volumetrics at Superpave gyration levels. The input data-set needed by the algorithm is composed of gradation of the mix, bulk specific gravity of aggregates, low- and high-performance grade of the binder, binder content of the mix and the target number of gyrations (i.e. N_ini, N_des and N_max). The proposed ANN model uses a three-layer scaled conjugate gradient back-propagation (feed-forward) network. The ANN was trained using data obtained from numerous roads with a total of 1817 different mix designs. Results revealed that the ANN was able to predict V_a within V_a (measured) ± 1.0% range 85–93% of the time and within V_a (measured) ± 0.5% range 60–70% of the time. Currently with the developed ANN model, Superpave mix design can take approximately between 1.5 and 4.5 days, which corresponds to 3–6 days of savings.