Effect of Composition and Size of Crystallite on Crystal Phase in Lead Barium Titanate

Lead titanate, barium titanate, and lead barium titanate powders (>99.9% pure), the particle size of which varied from 0.03 to 0.15 μm depending on the calcination temperature and the composition, was prepared from barium lead titanyl oxalate, which was previously prepared by reacting high-purity ammonium titanyl oxalate with barium and lead acetate. The critical crystallite size of BaTiO₃ powder from the cubic to the tetragonal phase is around 1 μm. Pb_0.3Ba_0.7TiO₃ powder with an average size of 0.057 μm showed the tetragonal phase.     

Stability,cure properties,and applicability as one part adhesives of systems of divalent metal salts of mono(hydroxyethyl) phthalate–anhydride–bisepoxide

Heterogeneous curable compositions of divalent metal salts of mono(hydroxyethyl) phthalate–anhydride–bisphenol A diglycidyl ether (BADG) systems were prepared by merely mixing these components at room temperature. Stability at room temperature and cure properties at high temperature of the compositions were investigated for evaluating their applicability as one part adhesive. It was found that the systems containing Mg were generally more stable than those containing Ca. Similarly, at 150°C the Ca-containing systems showed generally shorter gelation time than the Mg-containing ones, due to the fact that the Ca salt dissolves more rapidly and enters into the addition reaction with the anhydride, leading to the faster appearance of the catalytic activities of the Ca carboxylate group. Among the various combinations of components, the metal salt–succinic anhydride (SA)–BADG systems were stable at room temperature for more than 6 months and rapidly cured at high temperature, showing excellent adhesive properties. This result indicates that the SA-containing systems should be of interest in applications to one part adhesives.     

电子装置内的热移动研究——温度分布及速度分布

在高60cm,宽45cm 的模拟电子装置内,进行装置内热移动研究,得到不同条件下的温度分布及速度分布.在理论解析及数值计算基础上,进行无因次准数关联,得出实验式.实验结果及解析结果基本一致.利用所得实验式对正在运转或有待开发的新的电子装置有关参数进行推算,对于传热设计具有很强的实用性.     

Breaking Ability and Interrupting Phenomena of a Circuit Breaker Equipped with a Parallel Resistor or Capacitor

This paper discusses the breaking ability of an air blast circuit breaker (ABB) or SF6 gas circuit breaker (GCB), and the interrupting phenomena around current zero in the case where a resistor or capacitor is connected in parallel with its interrupter to improve the breaking ability. It has been clarified that the use of a parallel resistor for ABB, and that of a parallel capacitor for GCB are the most effective methods to improve the breaking abilities; the parallel resistor not only serves to reduce the rate of rise of the transient recovery voltage (rrrV), but also shifts the current from the interrupter to itself around the current zero, thus reducing the stress for interruption. The improvement of the breaking ability is achieved by reducing the initial average rrrV between zero and 1 microseconds (inherent value), when the parallel capacitor is used with the GCB.     

Gel permeation chromatography using controlled-porosity glass. II. Polyacrylamide aqueous solutions

In a study of polyacrylamide in solutions we have required the rapid characterization on chromatographies. The application to the aqueous solution of the GPC using controlled-porosity glass has been examined from both the viewpoint of the effect of salt addition and the GPC mechanism. An adequate addition to neutral salt, 0.005M KCI to the eluent, gave rise to the elution behaviors being in accord with the hydrodynamic volume concept of the GPC separation.     

Change of viscoelastic properties of epoxy resin in the curing process

This paper is concerned with the relation between the time and temperature dependences of the flexural properties and the curing conditions for the bisphenol A-type epoxy resin with acid anhydride hardener. Relaxation moduli of epoxy resin, prepared at several curing temperatures and times, were measured in the temperature range from T_g ?70°C to T_g. The master curves of relaxation modulus for the epoxy resin could be constructed, using their thermorheological simple properties. The time–temperature shift factors of the epoxy resin could be approximately expressed by the Arrhenius equation with the activation energy 59.4 kcal/mole. independent of its curing conditions. The curing time and temperature were equivalent, that is, the short curing time at high temperature corresponded to the long curing time at low temperature. The curing time–temperature shift factor could be approximately expressed by the Arrhenius equation with the activation energy 21.3 kcal/mole, which was higher than the activation energy 14.2 kcal/mole obtained in the measurements of gel times. The increase in the values shows that the temperature dependences of reaction rates increase with progressing gelation.     

Evaluation of the wettability of spherical cement particle surfaces using penetration rate method

The wettability of cement particles is related to the fluidity of cement paste. This paper describes the mechanism of the higher fluidity imparted by the spherical cement particles in light of their wettability. In addition, the effects of gypsum on the wettability were also studied. This study has shown the following: (1) The weight of water and water-reducing agent solution penetrating the spherical cement powder bed is 24-150% higher than that for the ordinary Portland cement powder bed. This results in the improvement of the wettability of the particle surfaces of spherical cement. The high wettability of spherical cement contributes to its high fluidity. (2) The presence of many fine gypsum particles on the spherical cement particle surface reduces the wettability. (3) To prepare spherical cement, the optimum amount of gypsum added is determined by the acceleration of the formation of spherical particles and the wettability of particle surfaces.     

Development of an on‐line partial discharge monitoring system for gas insulated substations

This paper describes the results of tests and discussions carried out to develop a system for partial discharge monitoring in GIS. They include the propagation characteristics of partial discharge pulses in each GIS component, as well as the test results obtained using an actual 300‐kV GIS. We also report the results of verification test on the GIS partial discharge monitoring and location system developed by the authors. © 1999 Scripta Technica, Electr Eng Jpn, 129(2): 40–50, 1999     

The dissociation process in plasma-enhanced chemical vapor deposition using tetraethoxysilane

Dissociation in plasma-enhanced chemical vapor deposition for SiO₂ deposition using tetraethoxysilane (TEOS) was investigated by means of mass spectrometry. First we obtained the basic dissociation patterns of TEOS by electron impact. It was shown that TEOS was dissociated by electron impact at low electron energies below 7 eV, removing the ethyl group (C₂H₅). Next we determined dissociation patterns in TEOS/He plasma in order to eliminate the effect of oxidation. Finally, dissociation in TEOS/O₂ plasma was investigated. It was found that oxidation plays an indispensable role in the deposition of high-quality SiO₂ films due to the decrease in high-molecular-weight compounds with carbon and hydrogen, although TEOS is highly dissociated by electron impact. © 1999 Scripta Technica, Electr Eng Jpn, 129(4): 32–38, 1999