New amphoteric surfactants containing a phosphoric acid group: I. syntheses and physicochemical properties of sodium 2-(n-2-hydroxyalkyl-n-methylamino)ethyl hydrogen phosphate

A series of new amphoteric surfactants having a phosphoric acid group, a tertiary amino group and a 2-hydroxyalkyl group, sodium 2-(N-2-hydroxyalkyl-N-methyl-amino)ethyl hydrogen phosphates (alkyl: n-tetradecyl, n-hexadecyl, n-octadecyl), were prepared by an addition reaction of 1,2-epoxyalkanes to N-methylaminoethanol, followed by the introduction of a phosphoric acid group and neutralization with sodium hydroxide. The structures of these compounds were confirmed by spectroscopy and elemental analysis. The solubility in solvents, Krafft point, surface tension, critical micelle concentration (CMC), occupation area of the molecule at the surface of aqueous solutions and foaming power were measured. It was shown that a 2-hydroxyethyl group in a long alkyl chain seemed to behave as a hydrophobic part.     

The degradation of polystyrene during extrusion

An investigation was made of the magnitude and mechanism of shear degradation of a narrow distribution, high molecular weight (M_w = 670,000) polystyrene. An Instron rheometer was used to perform the extrusion at temperatures from 164° to 250°C. The change in molecular weight distribution was studied by gel permeation chromatography. The maximum shear stress employed was 5.83 kg/cm². It was found that degradation could be induced at high stress at temperatures of 50°C lower than degradation of polystyrene would occur exclusively due to thermal forces. An activation energy for the degradation, calculated at constant shear rate, was +20.2 kcal/mole. The direction and magnitude of this value are consistent with degradation induced through a mechanical reduced activation for thermal degradation.     

Concentration of acetic acid in sulfite pulp evaporation drain by reverse osmosis

The evaporation drain of sulfite pulp spent liquor contains few volatile fatty acids, most of which is acetic acid. The main objective of this study is to recover acetic acid as the concentrated solution (about 4%), which could be used as a culture medium of the yeast. As acetic acid can easily pass through the cellulose acetate membrane, SP drains neutralized by NaOH, NH₄OH and Ca(OH)₂ were used as the feed solutions. In all cases, concentration by reverse osmosis was successfully carried out provided the appropriate pretreatment was employed. The recovery of acetic acid was 95.6, 90.5 and 98.2% for Na-, NH₄-, and Ca-drain, respectively. In addition, the recovered (permeated) water may be used as an industrial one.     

1-O-alkyl-2,3-diacylglycerols in the skin surface lipids of the hairless mouse

A neutral lipid class was isolated by thin-layer chromatography from the skin surface lipids of the hairless mouse. The fraction migrated faster than triglycerides and had a migration rate similar to that of diacyl alkanediols (diester wax). Upon deacylation, however, the long-chain diols were identified as 1-alkylglycerol ethers based on their chromatographic properties and on the mass spectra of their nicotinylidene derivatives. Thus, the skin lipid fraction was identified as 1-O-alkyl-diacylglycerol. The alkyl moieties were all saturated and even-numbered and ranged in chainlength from C₁₆ to C₂₂ with 1-O-hexadecylglycerol amounting to 34% of the total glycerol ether moieties. The fatty acids derived from this lipid fraction were mostly monoenoic with chainlengths ranging from C₁₆ to C₂₄. The major acyl component was eicosenoic acid (20∶1) representing 61% of the total fatty acids.     

Effects of 6-anilino-1,3,5-triazine-2,4-dithiol,zinc stearate,and barium stearate on the thermal stabilization of PVC

Individual action and synergistic effect in the combination of 6-anilino-1,3,5-triazine-2,4-dithiol (AF), zinc stearate, and barium stearate on the color stabilization of PVC were investigated. In this system, AF selectively reacts with allylic chlorine atoms in PVC. Consequently, unstable allylic chlorine units were converted to thermally stable allylic structures, thus retarding the development of polyene sequences. Zinc stearate accelerated the reaction of AF with allylic chlorine atoms in PVC, forming the zinc salts of AF (AFZ_nSt, St?C₁–H₃₅COO? ) by reacting with AF. Barium stearate reacted with ZnCl₂ which is formed in the above reaction to give St₂Zn and BaCl₂. Consequently, barium stearate led to the selective reaction of AF with allylic chlorine atoms in PVC and the remarkable retarding effect of discoloration of PVC.     

Polymerization of 2-dibutylamino-1,3,5-triazine-4,6-dithiol on wire during friction process

2-Dibutylamino-1,3,5-triazine-4,6-dithiol (DB) and a mixture of DB and triallylisocyanurate (TAIC) were used as a lubricant during steel wire drawing due to a dry process. DB gave a polymer film with 180 nm in thickness to wire surfaces during the wire drawing. The polymer film had a disulfide structure on the backbone and contained a small amount of DB monomer and olygomer. Molecular weight and polymer weight increased with the drawing rate. The mixture of DB and TAIC gave mainly a three-dimensional polymer film with 225 nm in thickness to wire surfaces during drawing. The polymer film insoluble in THF had mono and disulfide structures and contained a small amount of linear polymer, DB, and TAIC. Such tribological polymerizations are estimated as follows: DB produces dithiyl radicals on a nascent surface formed during drawing and in the presence of oxygen and heat. The dithiyl radicals were polymerized by coupling with each other to give disulfide bonds or added to allyl groups in TAIC to give monosulfide bonds. It is concluded that this technique should be possible to use for unifying metal processing and surface treatment. © 1995 John Wiley & Sons, Inc.     

Biased distribution of the branched-chain fatty acids in ceramides of vernix caseosa

The compositions of ester- and amide-linked fatty acids from ceramides of human vernix caseosa were described with emphasis on the distribution of the branched-chain fatty acid (BCFA). Two novel ceramides were isolated from vernix caseosa in the course of this study: the acylated type of esterified α-OH-hydroxyacid/sphingosine ceramide (Cer[EAS]) and nonacylated type of non-OH fatty acid/hydroxysphingosine ceramide (Cer[NH]). Their chemical structures were identified by nuclear magnetic resonance and chemical procedure. The Cer[EAS] was an acylceramide and consisted of the highest concentrations of ester- and amide-linked BCFA (62 and 67%, respectively). The iso- or anteiso-branching structures of the aliphatic chains were confirmed by the mass spectra of their picolinyl or pyrrolidide derivatives. As a whole, amide-linked fatty acids of ceramides 1–7 and Cer[NH] were normal types of straight-chain fatty acids with or without α- or ω-hydroxylation. The BCFA concentrations of amide-linked fatty acids in these ceramides (ceramides 1–7 and Cer[NH]) were low and less than 10%. The BCFA thus occurred exclusively in a novel acylceramide of Cer[EAS] in the vernix caseosa.     

Effect of Composition and Size of Crystallite on Crystal Phase in Lead Barium Titanate

Lead titanate, barium titanate, and lead barium titanate powders (>99.9% pure), the particle size of which varied from 0.03 to 0.15 μm depending on the calcination temperature and the composition, was prepared from barium lead titanyl oxalate, which was previously prepared by reacting high-purity ammonium titanyl oxalate with barium and lead acetate. The critical crystallite size of BaTiO₃ powder from the cubic to the tetragonal phase is around 1 μm. Pb_0.3Ba_0.7TiO₃ powder with an average size of 0.057 μm showed the tetragonal phase.     

Evaluation of the wettability of spherical cement particle surfaces using penetration rate method

The wettability of cement particles is related to the fluidity of cement paste. This paper describes the mechanism of the higher fluidity imparted by the spherical cement particles in light of their wettability. In addition, the effects of gypsum on the wettability were also studied. This study has shown the following: (1) The weight of water and water-reducing agent solution penetrating the spherical cement powder bed is 24-150% higher than that for the ordinary Portland cement powder bed. This results in the improvement of the wettability of the particle surfaces of spherical cement. The high wettability of spherical cement contributes to its high fluidity. (2) The presence of many fine gypsum particles on the spherical cement particle surface reduces the wettability. (3) To prepare spherical cement, the optimum amount of gypsum added is determined by the acceleration of the formation of spherical particles and the wettability of particle surfaces.     

Stabilization of poly(vinyl chloride). I. Change in color of poly(vinyl chloride) compounded with some metal soaps

Poly(vinyl chloride) (PVC) with one or more metal salts added was colored by the action of heat to investigate the stabilization mechanism. The coloration and the color difference of heated PVC compound films varied according to the metal salt added. The decoloration of the colored compound films was advanced markedly in THF, DMF, acetone, and ammonia. On the other hand, the heated achromatic PVC film containing Cd/Ba soaps underwent an opposite change, from colorless to yellow orange, in the above materials. This means that the coloration of heated compound films may result from the formation of some complex (for example, π complex of the polyene with the metal chloride). Furthermore, the colored film with cadmium stearate was decolored by roll mixing with the colored film containing barium stearate. These results indicate that the stabilization with metal soaps may be founded on a physical phenomenon such aa an effect of complementary color.