Aloe vera gel: a new thickening agent for pigment printing

An attempt was made to print cotton fabric with pigments using a new thickening agent based on Aloe vera gel in combination with sodium alginate. The results were compared with the standard conventional printing recipe containing synthetic thickener, and a favourable effect of Aloe vera introduction was achieved. The results show that the properties of the printed fabric (sharpness, colour yield, overall fastness properties, softness, and water vapour transmission) are dependent on the percentage of Aloe vera gel in the thickener combination, the concentration of printing auxiliaries, and the curing conditions. Optimal printing properties were achieved by using a printing paste containing 80% Aloe vera/20% sodium alginate (700 g kg^?1), pigment (50 g kg^?1), binder (145 g kg^?1), fixer (10 g kg^?1), and ammonium sulfate (5 g kg^?1), followed by drying at 85 °C for 5 min and curing at 150 °C for 3 min. The sample printed with the new recipe showed superior rubbing fastness and handle properties, with a slightly lower colour yield, when compared with the sample printed with synthetic thickener. Finally, economic issues arising from synthetic thickener substitution are highlighted.     

Prospects of non-edible neem (Azadirachta indica) oil in Bangladesh: performance and emission evaluation in a direct injection diesel engine

Transition to alternative energy is receiving serious attention globally and in this very way, biodiesel from inedible neem can be an alternative to conventional liquid fuels as it contains 30–45%?wt of oil. In this study, esterification and transesterification reaction of methanol and triglycerides at a molar ratio of 7:1 was done and maximum 96% by volume biodiesel was extracted. Physiochemical properties of neem biodiesel lies within ASTM standards and Fourier transform infrared spectroscopy analysis of neem biodiesel reveals the presence of strong esters and the alkane group. The maximum efficiencies were found to be 22.8% and 22.3%, whereas minimum brake specific fuel consumptions were observed to be 0.57 and 0.59?kg/kW-hr for diesel and B20, respectively. Moreover, B20 provides less emission of HC, CO_x and increase in NO_x. Taking all into consideration, if at least 60% of the arid lands is utilised to cultivate neem trees then it will minimise the import of fossil fuel to an extent of 8.75%.     

Synthesis of Co3O4 @ Organo/Polymeric Bentonite Structures as Environmental Photocatalysts and Antibacterial Agents for Enhanced Removal of Methyl Parathion and Pathogenic Bacteria

Two green nanocomposites of Co₃O₄ decorated CTAB/bentonite (Co@CT/BE) and chitosan/bentonite (Co@CH/BE) were synthesized as enhanced and environmental photocatalysts and antibacterial agents. As photocatalysts, the products were applied in the effective oxidation of toxic methyl parathion pesticide (MP) in wastewater under a visible light source. The application of Co@CH/BE (0.02 g) resulted in the complete oxidation of MP (50 mg/L) after 40 min and complete mineralization after 60 min. while the complete oxidation and mineralization of MP (50 mg/L) by Co@CT/BE was recognized after 75 min and 100 min, respectively. The Co@CH/BE composite is of higher activity than Co@CT/BE and can cause complete oxidation for MP at high concentrations up to 100 mg/L after 75 min. The oxidation pathway was illustrated considering the existence of the hydroxyl radicals as the active oxidizing species and the identified secondary organic compounds during the oxidation tests. The detected intermediate converted into end products of CO₂ and inorganic anions of SO₄^?2, NO₃^?, and PO₄^?3 at the final stages of the oxidation processes. As antibacterial agents, the two composites exhibit considerable inhabitation zones of about 20 mm against both the Gram-positive Staphylococcus aureus and Gram-negative bacterium Vibrio Sp. The synthetic Co@CH/BE showed the best antibacterial properties with 200 μg/mL as minimum inhibitory against Staphylococcus aureus.

     

Silicon Application Enhances the Photosynthetic Pigments and Phenolic/Flavonoid Content by Modulating the Phenylpropanoid Pathway in Common Buckwheat under Aluminium Stress

Silicon - Silicon (Si) is very effective in the amelioration of heavy metal (HM) stress in different crop plants. This investigation was conducted to assess the protective role of Si in modulating...     

Structural and magnetic properties of Pr–Ni substituted Ca0.5Ba0.5Fe12O19 hexa-ferrite nanoparticles

Effect of Pr–Ni substitution on structural and magnetic properties of Ca_0.5Ba_0.5−xPr_xNi_yFe_12−yO₁₉ (x=0.00–0.10 and y=0.00–1.00) prepared by the sol–gel auto combustion method were investigated. The XRD analysis confirmed the single phase M-type hexa-ferrite structure. The lattice parameters were found to increase as Pr–Ni content increases, which is attributed to the ionic size of the implicated cations. The Pr–Ni seems to be completely soluble in the lattice. Transmission electron microscopy reveals that the grain size decreases with increase of Pr–Ni substitution. The coercivity and remanent magnetization ranges from 1511 to 1925 (Oe) and 21.4 to 26.5 (emu/g), respectively. The coercivity values of all the samples fall in the range of M-type hexa-ferrites.     

Enzyme Processing of Soy Flour with Minimized Protein Loss

The enzymatic treatment of defatted soy flour (SF) to reduce indigestible carbohydrates can result in undesirable protein loss. Here protein loss was minimized with quantitation of the effects of ionic strength (IS), protease activity, and SF toasting. At the enzyme processing condition (25% w/v SF, 50 °C, pH 4.8, 48 hours), protein loss increased linearly with the IS in enzyme broths (EB); e.g., contacting untoasted SF with water or heat-deactivated EB showed protein loss of 28% in water but up to 40% when IS was increased in the range of 0.04–0.19 M. Protein loss also increased with protease in EB (nondeactivated): after adjusted for IS-related loss, approximately 10% and 25% additional protein loss occurred in EB of 73 and 490–557 U/(g SF) protease, respectively. SDS-PAGE results showed that proteolysis was not extensive, mainly on β-conglycinin α'/α and glycinin acidic 37-kDa subunits; and most of the proteolytic products could be recovered by heat-induced precipitation. SF toasting effects were studied, particularly at 2-hours 160°C, with material balances, protein distributions, and monosaccharide yields in hydrolysates. Overall, protein loss was minimized to 5.2% and the conversion of carbohydrate to monomeric sugars increased to 89.2%.     

Investigation of improved dielectric and thermal properties of ternary nanocomposite PMMA/MXene/ZnO fabricated by in-situ bulk polymerization

Electric power system applications demand for high-temperature dielectric materials. The improved performance of polymer nanocomposites requires improvement in their thermal conductivity & stability, dielectric stability and processing technique. However, they often lose their dielectric properties with a rise in temperature. Here, we offer a solution by incorporating electrically conducting material (MXene) and semiconducting inorganic nanoparticles (ZnO NPs) into an insulating PMMA polymer matrix to maintain high dielectric constant, both at the room and high temperature. Therefore, to achieve desirable thermal and dielectric properties is the main objective of the present study based on the homogeneous distribution of the nanofillers by in-situ bulk polymerization assisted by strong sonication in the corresponding polymer. The introduction of MXene and ZnO NPs into the PMMA not only acquires a substantial increment in the dielectric constant, to attain a value 437, with minimum energy loss of 0.36 at 25 Hz, but also improves the thermal conductivity of PMMA up to 14 times by causing the reduction of thermal resistance, which is actually responsible for the poor thermal conductivity of amorphous pure PMMA polymer. More importantly, hybrid PMMA/4:2 wt% MXene:ZnO nanocomposite leads to an excellent thermal stability. Moreover, further characterization of the synthesized nanocomposites by FTIR, SEM and XRD leads to the evaluation of strong interaction of ternary components with PMMA matrix.     

Effect of pH,Temperature and Reaction Time on Calcium Binding by Hydroxypropyl Rice Starches

Calcium binding by both native and hydroxypropyl starches was studied in aqueous media under different pH, temperature and reaction times at various calcium: starch ratios. Calcium binding was markedly influenced by pHs and temperatures of the reaction mixture. Reaction times did not show marked influence on calcium binding. Maximum calcium binding was observed in alkaline pH and at lower temperature. Most of the calcium bound within the first 20 minutes. Thus, alkaline pH and lower temperature is more favourable for calcium binding by both native and hydroxypropyl rice starches compared to acidic pH and higher temperatures.     

Flexible and Conductive 3D Printable Polyvinylidene Fluoride and Poly(N,N‐dimethylacrylamide) Based Gel Polymer Electrolytes

In this work, 3D printable gel polymer electrolytes (GPEs) based on N,N‐dimethylacrylamide (DMAAm) and polyvinylidene fluoride (PVDF) in lithium chloride containing ethylene glycol solution are synthesized and their physicochemical properties are investigated. 3D printing is carried out with a customized stereolithography type 3D gel printer named “Soft and Wet Intelligent Matter‐Easy Realizer” and free forming GPE samples having variable shapes and sizes are obtained. Printed PVDF/PDMAAm‐based GPEs exhibit tunable mechanical properties and favorable thermal stability. Electrochemical proprieties of the printed GPEs are carried out via impedance spectroscopy in the temperature range of 25–90 °C by varying PVDF content. Ionic conductivity as high as 6.5 × 10^?4 S cm^?1 is achieved at room temperature for GPE containing low PVDF content (5 wt%) and conductivity of the GPEs is increased as temperature rises.     

Patterning of worm-like soft polydimethylsiloxane structures using a TiO2 nanotubular array

Patterned polydimethylsiloxane (PDMS) is an important structure for soft lithography. Various materials have been deployed as mold for patterning PDMS. Anodized nanotubular array has been sought after as cost-effective alternative for textured silicon. An array of TiO₂ nanotubes with characteristic diameter ≈140 nm and the length of ≈1.5 microns, created by anodic oxidation of a titanium substrate, was used here as a template for soft PDMS molding. The optimal molding process was developed by a combination of silanization, use of solvent, application of a vacuum, and hydraulic pressing. The silanization was confirmed by Fourier transform infrared spectroscopy and contact angle measurements while the PDMS structure was examined by scanning electron microscope and energy dispersive X-ray spectroscopy. Hydraulic pressing significantly improved the infiltration of PDMS into the pores of nanotubular array resulting in formation of PDMS nanobumps after separation of the polymer from the template. Complete infiltration of PDMS precursor into the cavity of nanotubes was observed on the hydraulic-pressed sample without toluene impurities. The hydraulic-pressed samples exhibited higher adhesion strength than nonpressed ones. The adhesive strength was measured by a simple experimental arrangement, in which the PDMS layer was stuck on a vertical glass surface followed by pulling it downwards.