A single-chip storage LSI for home networks

Network direct attached storage (NDAS) is a network storage architecture that allows direct attachment of existing ATA/ATAPI devices to Ethernet without a separate server. Unlike other architectures such as NAS, SAN, and USB mass storage, no server computer intervenes between the storage and the client hosts. We describe an NDAS disk controller (NDC) amenable to low-cost single-chip implementation that processes a simplified L3/L4 protocol and converts commands between ATA/ATAPI and Ethernet, while the remaining complex tasks are performed by remote hosts. Unlike NAS architectures that use TCP/IP, NDAS uses a TCP-like lean protocol that lends itself well to high-performance hardware realization. Thanks to the simple NDAS architecture and protocol, an NDC implemented on a single 4 mm /spl times/ 4 mm chip in 0.18 /spl mu/m CMOS technology achieves a maximum throughput of 55 Mbytes/s on gigabit Ethernet, which is comparable to that of a high-performance disk locally attached to a host computer.     

在LabVIEW程序运行中实现控件的动态移动

通过两种在LabVIEW程序运行中实现控件移动的方法的对比,着重介绍了结合了VI Sever技术的动态注册事件结构的用法,从而总结出其具有优化程序、减少内存、提高CPU利用率等方面的优点.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

Solution of a multidimensional inverse radiation problem by means of mode reduction

The Karhunen–Loève Galerkin procedure is employed to solve an inverse radiation problem of determining the time‐varying strength of a heat source, which mimics flames in a furnace, from temperature measurements in three‐dimensional participating media where radiation and conduction occur simultaneously. The inverse radiation problem is solved through the minimization of a performance function, which is expressed by the sum of square residuals between calculated and observed temperature, using a conjugate gradient method. Through the Karhunen–Loève Galerkin procedure, one can represent the system dynamics with a minimum degree of freedom, and consequently the amount of computation required in the solution of the inverse problem is reduced drastically when the present technique is adopted. Copyright © 2004 John Wiley & Sons, Ltd.     

Workplane illuminance prediction method for daylighting control systems

A new prediction method with an interior light sensor for the workplane illuminance in daylighting control systems is introduced. Based on radiosity theory, the spatial distributions of daylight and electric light in the space are discussed and the prediction method is developed. An experimental verification of the technique is performed in an outdoor test-room for a double-glazed window system with a motorized venetian blind integrated between the two glazings. Electric light and daylight predictions were performed in accordance with the proposed method. The results showed that the electric light workplane illuminance can be predicted with high accuracy (±5 lux error with a linear correlation) and that the daylight workplane illuminance can be predicted within ±20 lux (with a linear correlation) for any sky conditions (overcast, clear sky, or variable) with the window system controlled to prevent direct daylight transmission. This method is useful for integrated control of motorized daylighting devices and dimmable electric lights.     

基于μCLinux的NAT设备的设计与开发

NAT(网络地址翻译)技术有效地解决了IP地址紧缺的问题,为实现IPv4到IPv6的平滑过渡发挥了巨大的作用.在一个体积小、重量轻、价格低廉的嵌入式平台上实现NAT设备具有很好的实际意义.文中介绍了NAT技术的原理和实现过程,在自行设计的ARM7嵌入式硬件平台上基于μCLinux操作系统实现了NAT的功能,并通过实现其他相关功能,构建了完整的NAT设备,完成了小型网络接入Internet的方案.     

High performance biofilm process for treating wastewater discharged from coal refining plants containing nitrogen, cyanide and thiocyanate.

Wastewater discharge from coal refining plants contains a number of biologically toxic compounds; 2000-2500 mg/l of COD of which 40% is composed of phenol, 100-400 mg/l of thiocyanate, 10-40 mg/l of cyanide, 100-250 mg/l of NH4+-N and 150-300 mg/l of total nitrogen. In order to treat this kind of high strength wastewater, we have developed a high performance biofilm process using fluidizing bio-carriers of the tube chip type. The fluidizing biofilm carriers are made of a composite of polyethylene and several inorganic materials, whose density is controlled at 0.97-0.98 g/ml. The fluidizing biofilm carriers show sound fluidization characteristics inside bioreactors. The wastewater is treated using three consecutive series reactors in oxic-anoxic-oxic arrangement. Each reactor is charged with the fluidizing biofilm carriers of 50 vol%. Furthermore, newly cultured active microorganisms for the thiocyanate biodegradation are added in the biofilm process. At total hydraulic retention time of 2.2 days, this process can achieve steady state removal efficiencies: COD, 99%; thiocyanate, 99%; NH4+-N, 99% and total nitrogen, 90%.