Efficient traffic prediction scheme for real-time VBR MPEG videotransmission over high-speed networks

The efficient transportation of real-time variable bit rate (VBR) video traffic in high-speed networks is currently an active area of research. The capability to predict VBR video traffic can significantly improve the effectiveness of numerous management tasks, including dynamic bandwidth allocation and congestion control. This paper proposes an adaptive traffic prediction method for VBR MPEG videos, a major multimedia application. Rapid traffic variations due to scene changes are analyzed, then a prediction scheme using the identification of scene changes related to I and P frames is presented. For predicting multiplexed MPEG traffic, a prediction interval is derived that represents a highly correlated traffic sequence. In addition, to reduce the prediction error, a less fluctuating signal instead of the original multiplexed traffic is used as the input for the predictor. Simulation results show that the proposed method is able to predict the original traffic more accurately than the conventional LMS method     

Investigation of driving performance, vection, postural sway, and simulator sickness in a fixed-based driving simulator

This paper reports the results of a pilot study conducted to determine whether there is a relationship between simulator sickness and measures of driver inputs, vection, and postural sway, in a fixed base driving simulator. Seven males and four females performed a series of alternating left and right turns (20 each), with straigth-aways inbetween. The task was designed to promote experiences of circular and linear vection, and associated sway. It was hypothesized that greater driver inputs (i.e., steering wheel and braking activity; deviation from the centerline) would correlate: with reports of vection and measures of postural sway. Ten of the eleven subjects reported moderate sickness, which precluded any statistical comparisons between “sick” and “not sick” however, there was a significant tendency for persons who reported vection to also report sickness. There were no gender differences in reported incidence of vection or sickness, however, males tended to exhibit greater lateral velocity. The next phase of investigation will necessitate reducing the strength of the stimulus (i.e., require less turns) to increase variability of sickness scores amongst subjects and permit comparisons between “sick” and “not sick.” Measurement considerations include increasing the sensitivity of vection ratings, and examination of the timecourse for the development of postural sway.     

Frequency tuning technique for Gm-C filters

A frequency tuning technique based on an envelope locked loop is proposed for Gm-C filters. A degenerated integrator is used as the master circuit to eliminate the problems associated with the DC offset of the operational transconductance amplifier (OTA)     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal convection in a horizontal porous layer with spatially periodic boundary temperatures: small Ra flow

This study considers a small Rayleigh number thermal convection in a fluid-saturated porous medium between two infinite-horizontal walls. The lower and upper walls have sinusoidal temperature distributions with a wave number and a phase difference, and the effect of the parameters on the flow and heat transfer characteristics is investigated. For a given wave number, an out-of-phase configuration yields minimum heat transfer at the walls. Maximum heat transfer occurs at the wave number of 2.286 with an in-phase configuration.     

Superconductivity in Lithium- and Sodium-Doped Mercury-Based Cuprates

The effect of Na- and Li-doping in Hg-based cuprates has been studied. It has been found that superconductivity can be achieved in samples containing small amount of Na or Li. While little change is found in the crystalline structure, the formed superconducting phase have the onset T_c typically above 140 K and zero-resistance T_c up to 136K. More interestingly, the processing temperature for the doped Hg-1223 can be reduced significantly to near 700 °C which is promising for thin films growth on many technologically compatible substrates.     

Thermal properties and crystalline structure of liquid crystalline poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate)

Thermal properties and crystalline structure of liquid crystalline (LC) poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate) [copoly(ET/CPT)] were investigated using differential scanning calorimetry (DSC), thermogravimetry (TGA), limiting oxygen index (LOI) measurement, electron dispersive X‐ray analysis (EDX), X‐ray diffractometry, and infrared spectrometry (IR). The thermal transition temperatures of copoly(ET/CPT) were changed with the composition. Copoly(ET/CPT) showed two thermal decomposition steps and the residues at 700°C and LOI values of copoly(ET/CPT) were almost proportional to its chlorine content. The activation energy of thermal decomposition of LC units was very low compared to that of poly(ethylene terephthalate)(PET) units. Crystal structure of copoly(ET/CPT) (20/80) was of triclinic system with the lattice constants of a = 9.98 A?, b = 8.78 A?, c = 12.93 A?, α = 97.4°, β = 96.1°, and γ = 90.8°, which is very close to that of poly(chloro‐p‐phenylene terephthlate) (PCPT) with the lattice constants of a = 9.51 A?, b = 8.61 A?, c = 12.73 A?, α = 96.8°, β = 95.4°, and γ = 90.8°. When copoly(ET/CPT)(50/50) was annealed at 220°C in vacuum, crystallization induced sequential reordering (CISR) was not observed but the heat of fusion was slightly increased due to the increase of the trans isomer content in PET units. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1286–1294, 2002; DOI 10.1002/app.10451     

Pore‐free mold‐pattern‐transfer method for barrier ribs of HD PDPs

Abstract— Among various barrier‐rib manufacturing processes, the mold‐pattern‐transfer method has potential to reduce processing cost as well as the manufacture of high‐resolution pixels. In this study, the effects of major processing variables of the mold‐pattern‐transfer process on the formation of air‐trapped pores within barrier ribs were examined. The results indicated that with an optimum combination of the processing variables, barrier ribs without trapped defects can be produced, demonstrating the possibility of reducing the number of processing steps and costs of barrier ribs.