Austenitizing treatment influence on the electrochemical corrosion behavior of 0.3C-14Cr-3Mo martensitic stainless steel

Effects of austenitizing treatment temperatures on aqueous corrosion properties of martensitic stainless steels were investigated by electrochemical tests (potentiodynamic test, potentiostatic test and electrochemical impedance spectroscopy), and surface analyses (optical microscopy and XRD). The results of potentiodynamic test revealed that the breakdown potential increased with the increased austenitizing temperature, indicating increased relative resistance to initiation of localized corrosion. EIS measurements showed that MSS3 (1030 °C) exhibits larger polarization resistance value than MSS1 (970 °C) and MSS2 (1000 °C) at passive and breakdown states. This was caused by decreasing the amount of Cr-rich M₂₃C₆ carbide which acts as preferential sites for pitting corrosion.     

Dynamics modeling and analysis of a biped walking robot actuated by a closed-chain mechanism

We developed a new type of human-sized biped walking robot (BWR) driven by the closed-chain type of joint actuator. Each leg of the robot is composed of three pitch joints and one roll joint. In all, a 15 degree-of-freedom robot including four arm joints and three joints for the head was developed. The BWR was developed to walk autonomously such that all leg joints are actuated by small 90 W dc motors/drivers and dc batteries and controllers which are boarded. The joint actuator for the BWR is composed of the four-bar-link mechanism driven by the ball screw which has high strength and high gear ratio. A dynamics modeling of the developed BWR for forward walking is presented in which the revolute joint dynamics are transformed into the prismatic joint dynamics of the ball screw. Also, an analysis on the four-bar-link mechanism applied to the joint actuator and on the structure of the BWR is shown. The design specification of the actuating motor for the BWR is analyzed through the torque analysis of the four-bar-link actuator. Through walking experiments of the BWR, the walking performance and trajectory tracking ability is shown. © 2004 Wiley Periodicals, Inc.     

A self-resonant frequency-modulated micromachined passive pressure transensor

In this paper, we report on the design, fabrication, and test of a passive pressure transensor. The sensor uses the self-resonant frequency modulation of an integrated coil to detect the pressure variations. This modulation is generated by the relative displacement of a ferrite core attached to a silicone rubber membrane. This scheme simplifies the packaging of the passive transensor by removing the requirement for a separate capacitor to form the resonator. A 30-turn 1.7-/spl mu/H coil having dimensions of 3/spl times/3 mm/sup 2/ is used in a prototype design yielding a sensitivity of 9.6 kHz/kPa with a cylindrical ferrite core of 0.95-mm diameter and 0.5-mm height. We also present a theoretical model of the sensor that shows good agreement with the experimental data. This model can be a useful tool for further optimization of the senors.     

Trenched‐Sinker LDMOSFET (TS‐LDMOS) Structure for 2 GHz Power Amplifiers

This paper proposes a new LDMOSFET structure with a trenched sinker for high‐power RF amplifiers. Using a low‐temperature, deep‐trench technology, we succeeded in drastically shrinking the sinker area to one‐third the size of the conventional diffusion‐type structure. The RF performance of the proposed device with a channel width of 5 mm showed a small signal gain of 16.5 dB and a maximum peak power of 32 dBm with a power‐added efficiency of 25% at 2 GHz. Furthermore, the trench sinker, which was applied to the guard ring to suppress coupling between inductors, showed an excellent blocking performance below ?40 dB at a frequency of up to 20 GHz. These results confirm that the proposed trenched sinker should be an effective technology both as a compact sinker for RF power devices and as a guard ring against coupling.     

Data retention characteristics of sub-100 nm NAND flash memory cells

In contrast to the conventional theories, we have revealed that the most distinguished mechanism in the data retention phenomenon after Fowler-Nordheim (FN) stress in sub-100 nm NAND Flash memory cells is the annihilation of interface states. Interface state generation rate increases rapidly as the channel width of NAND flash cell decreases. Comparison of interface states and stress-induced leakage current (SILC) component during retention mode shows that the annihilation of interface states strongly affects data retention characteristics of the programmed cells.     

Adaptive contour smoothing based on inter-region contrast

An adaptive contour smoothing algorithm designed as a preprocessor for shape coders is presented. In the method, the degree of the adaptive smoothing is controlled based on the significance of each contour point, which is quantified according to inter-region contrast in an intensity image. The actual smoothing consists of an expansion operator and a thinning algorithm.     

Mechanism of simultaneous solutes separation and concentration by size exclusion cyclic separation

The semicontinuous separation/concentration of two solutes with different molecular size by the size exclusion cyclic separation method is based on the opposite swelling responses of two gels to a temperature change. Experimental results of separation and concentration of solutes are verified qualitatively by the theoretical models based on the local equilibrium assumption. Separation of two solutes is shown by the breakthrough curves in coupled gel columns. In closed coupled columns, the volumetric space for the large molecules which are totally excluded from the gels becomes smaller, creating a concentrating effect as the gels swell when temperature changes. A mechanistic model is suggested to predict the large molecule concentration to increase to its solubility limit as cycle repeats.     

Role of conserved Asn-Tyr-Asp-Tyr sequence in bacterial copper/2,4, 5-trihydroxyphenylalanyl quinone-containing histamine oxidase

Copper amine oxidase contains a covalently bound quinonoid cofactor, 2,4,5-trihydroxyphenylalanyl quinone (TPQ), which is synthesized by post-translational modification of a specific tyrosyl residue occurring in the highly conserved sequence, Asn-Tyr-(Asp/Glu)-Tyr. To elucidate the role(s) of the conserved sequence in the biogenesis of TPQ, each of the corresponding residues at positions 401-404 in the recombinant histamine oxidase from Arthrobacter globiformis has been replaced with other amino acids by site-directed mutagenesis. When Asn-401 was changed to Asp or Gln, the rate of TPQ formation by copper-dependent self-processing was 10(3)- to 10(4)-fold slower than in the wild-type enzyme. When Tyr-402 was replaced by Phe, TPQ was not formed at all, showing that Tyr-402 is essential as the precursor to TPQ. In contrast, Asp-403 could be replaced by Glu without changes in the rate of TPQ formation, whereas its replacement by Asn led to a marked decrease. Furthermore, when Tyr-404 was changed to Phe, TPQ was formed swiftly on incubation with copper ions, but the TPQ enzyme exhibited very low activity with altered substrate specificity. These results collectively indicate that a very rigorous structural motif is required for efficient formation of TPQ and for the catalytic activity in the active site of copper amine oxidases.