Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

Microwave dielectric properties of ultra-low loss Li2MgTi0.7(Mg1/3Nb2/3)0.3O4 ceramics sintered at low temperature by LiF addition

In this work, ultra-low loss Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics were successfully prepared via the conventional solid-state method. X-ray photoelectron spectroscopy (XPS), thermally stimulated depolarization current (TSDC) and bond energy were used to determine the distinction between intrinsic and extrinsic dielectric loss in (Mg_1/3Nb_2/3)⁴⁺ ions substituted ceramics. The addition of (Mg_1/3Nb_2/3)⁴⁺ ions enhances the bond energy in unit cell without changing the crystal structure of Li₂MgTiO₄, which results in high Q·f value as an intrinsic factor. The extrinsic factors such as porosity and grain size influence the dielectric loss at lower sintering temperature, while the oxygen vacancies play dominant role when the ceramics densified at 1400?°C. The Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics sintered at 1400?°C can achieve an excellent combination of microwave dielectric properties: ε_r =?16.19, Q·f?=?160,000?GHz and τ_f =??3.14?ppm/°C. In addition, a certain amount of LiF can effectively lower the sintering temperature of the matrix, and the Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄-3?wt% LiF ceramics sintered at 1100?°C possess balanced properties with ε_r?=?16.32, Q·f?=?145,384?GHz and τ_f =??16.33?ppm/°C.     

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.     

Appraisal of Agriglass in Promoting Maize Production Under Abiotic Stress Conditions

An agriglass composition containing different oxides acts as a slow release for macro and micro nutrients and was chosen to improve maize yield under most important abiotic stresses which affecting agriculture development; salinity and drought. A field experiment was performed in salt affected soil (EC =?7.5 dSm^??1) by using different water deficit rates (I1 = 100, I2 = 85 and I3 = 70% of maize water requirements). Irrigation levels were located in main plots. Every main-plot divided into six sub-plots contained glassy fertilizer treatments [F1 = 55 kg fed^?1 with 1/2 mm diameter of agriglass (fed. =?4200 m²), F2 = 55 kg fed^?1 with 1 mm diameter, F3 = 80 kg fed^?1 with 1/2 mm diameter, F4 = 80 kg fed^?1 with 1 mm diameter, F5 = Recommendations of Ministry of Agriculture and F6 = control]. The experimental results demonstrated that, ears, straw, grains and biological yields increased with increasing both water and agriglass rates. Application of agriglass as a slow release fertilizer improved yield more than mineral fertilizer. Some growth parameters, water use efficiency (IWUE), macronutrients concentration and their relations were included. Other studies on residual effect of agriglass and the annual application rates to withstand salinity and drought stress by strategic crops are required.     

Effect of ZnO layer thickness upon optoelectrical properties of NiO/ ZnO heterojunction prepared at room temperature

In this work, p-NiO/n-ZnO heterostructures were successfully prepared at room temperature using RF sputtering technique. The influence of ZnO layer thickness on the performance of the heterojunction was investigated. The deposited ZnO layers have a hexagonal Wurtzite structure with preferable growth orientations along (002) and (103) for thinner films. Increasing the thickness results in more crystallographic orientation randomness. The current–voltage measurements of the realized heterojunctions showed a clear rectifying behavior. The measured ideality factor varies from 2.5 to 1.6 according to the thickness of ZnO layer. The series resistance of the device is enlarged with increasing ZnO thickness. The deduced parameters from the I–V characteristics suggest that 200 nm is the optimal thickness of the ZnO layer according to our experimental conditions. We attribute the relatively better performance of this thickness to achieving reasonable compensation between serial resistance and ideality factor. The best heterojunction was tested and successfully used as a UV detector.     

Cross-Layer Optimization of Dynamic Packet Assignment for Video Transmission Over IEEE 802.11e Networks

Video transmission over IEEE 802.11e wireless networks still shows poor performance for large bandwidth demand and frequently changed environments. Thus, several enhancements of IEEE 802.11e were proposed. On the other hand, big frames and simultaneous sending of adjacent frames always cause packet dropping for buffer overflow. In the past, we proposed an IEEE 802.11e enhancement named DFAA and a content aware mechanism to solve the above problems. The motivation of this paper is to find a proper way to integrate these two mechanisms. A DFAA enhancement (DFAA-E) is proposed to make up the insufficiency of content aware mechanism. Experiments results show that the combination of DFAA-E and content aware mechanism improves the video decoded quality greatly. And its performance can be further enhanced by selecting the suitable settings of certain parameters.     

Reoptimization framework and policy analysis for maritime inventory routing under uncertainty

We study a maritime inventory routing problem, in which shipments between production and consumption nodes are carried out by a fleet of vessels. The vessels have specific capacities and can be chartered under different agreements. The inventory levels of all consumption nodes and some production nodes should be maintained within specified bounds; for the remaining production nodes, orders should be picked up within pre-defined time windows. We propose a discrete-time mixed-integer programming model. In the face of new information and uncertainty, this optimization model has to be re-solved, as the horizon is rolled forward. We discuss how to account for different sources of uncertainty. We present a rolling-horizon reoptimization framework that allows us to study different policies that impact the quality of the implemented solution, so we can identify the optimal set of policies.     

A Constitutive Equation of Thermoelasticity for Solid Materials

A new constitutive equation of thermoelasticity for crystals is presented based on the interatomic potential and solid mechanics at finite temperature. Using the new constitutive equation, the calculations for crystal copper and graphene are carried out under different loading paths at different temperatures. The calculated results are in good agreement with those of the previous thermoelasticity constitutive equation based on quantum mechanics, which clearly indicates that our new constitutive equation of thermoelasticity is correct. A lot of comparisons also show that the present theory is more concise and efficient than the previous thermal stress theory in the practical application.