High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Origin of the threshold voltage instability in SiO/sub 2//HfO/sub 2/ dual layer gate dielectrics

The magnitude of the V/sub T/ instability in conventional MOSFETs and MOS capacitors with SiO/sub 2//HfO/sub 2/ dual-layer gate dielectrics is shown to depend strongly on the details of the measurement sequence used. By applying time-resolved measurements (capacitance-time traces and charge-pumping measurements), it is demonstrated that this behavior is caused by the fast charging and discharging of preexisting defects near the SiO/sub 2//HfO/sub 2/ interface and in the bulk of the HfO/sub 2/ layer. Based on these results, a simple defect model is proposed that can explain the complex behavior of the V/sub T/ instability in terms of structural defects as follows. 1) A defect band in the HfO/sub 2/ layer is located in energy above the Si conduction band edge. 2) The defect band shifts rapidly in energy with respect to the Fermi level in the Si substrate as the gate bias is varied. 3) The rapid energy shifts allows for efficient charging and discharging of the defects near the SiO/sub 2//HfO/sub 2/ interface by tunneling.     

Power combining characteristics of backed-off traveling wave tubes for communications applications

Traveling wave tubes (TWTs) used in multi-tone and digital communications applications are typically operated backed off from saturation in order to improve the amplifier linearity. This reduces the bit error rate (BER), decreases intermodulation distortion and lowers adjacent channel power; all at the expense of reducing the average output power. For emerging telecommunications applications, the average power requirement is increasing to provide higher bit rates and lower BER, and often exceeds the power obtainable from backed-off space or telecommunications TWTs. One solution is to power combine TWTs that are operated 3 to 10 dB backed off from saturation. Efficient power combining requires that the phase and gain of the signal from each TWT be closely matched. To understand the variation in these parameters across a build-set of tubes, the phase and gain versus drive of 35 Boeing S-band 5525H TWTs were measured. The standard deviation in the phase about the mean phase shift measured at saturation was found to be 2.6/spl deg/, with a related standard deviation of the gain compression at saturation of 0.22 dB. These levels result in small power combining losses and small errors in phased-array fed multi-beam antennas in broadband multi-tone applications.     

Thermal aging of plasticized PVC. I. Weight loss kinetics in the PVC—didecylphtalate system

Weight-loss kinetics were studied for 10 industrial extruded samples of poly(vinyl chloride) (PVC) plasticized by 20–30% by weight of didecylphtalate at 85, 95, 105, 110, and 120deg;C. For the most unstable samples, which contained a light coplasticizer, the weight-loss rate obeyed Fick's law. In the other cases, it was constant in the early period of exposure. The apparent Arrhenius parameters (i.e., preexponential factor and activation energy) were intercorrelated and varied strongly from one sample to another. This was explained by the existence of two distinct kinetic regimes corresponding, respectively, to diffusion or evaporation, the whole process being controlled by the slowest step, and a transition between both regimes occurring in the temperature range of exposure. In the proposed model, small changes of the preexponential factor of diffusion from one sample to another are sufficient to take into account the observed behavior.     

Production of hot-dipped tin plate 0.45–0.50 mm thick

Magnitogorsk Metallurgical Combine. Translated from Metallurg, No. 2, p. 37, February, 1991.     

Evaluation of solid-desiccant-based evaporative cooling cycles for typical hot and humid climates

This paper presents an evaluation of various solid desiccant cycles for air conditioning in hot and humid climates. Psychometric evaluation of potential cycles for 16 typical Indian cities has been carried out with the objective of achieving standard comfort conditions in the room. Computer simulation is based on constant effectiveness of heat exchangers and evaporative coolers and actual performance data of a commercially available desiccant wheel dehumidifier. The influence of various outdoor conditions, the effectiveness of heat exchangers/evaporative coolers on the cooling coefficient of performance and volumetric air flowrate per unit cooling capacity have been investigated. It is found that amongst ventilation, recirculation and Dunkle cycles, the Dunkle cycle is better for a wide range of outdoor conditions. However, cycles using wet surface heat exchangers give even higher performance.     

Influence of the Temperature of a Body on Its Weight

The physical preconditions are considered for the temperature of a body to influence the force of gravity experienced by it. The results are given of experiments on weighing metal rods heated by ultrasound which confirm a dependence of the weight of the rods on their temperature.     

Effect of exponentially graded base doping on the performance ofGaAs/AlGaAs heterojunction bipolar transistors

The authors have fabricated n-p-n GaAs/AlGaAs heterojunction bipolar transistors (HBTs) with base doping graded exponentially from 5×10¹⁹ cm^-3 at the emitter edge to 5×10¹⁸ cm^-3 at the collector edge. The built-in field due to the exponentially graded doping profile significantly reduces base transit time, despite bandgap narrowing associated with high base doping. Compared to devices with the same base thickness and uniform base doping of 1×10¹⁹ cm^-3 , the cutoff frequency is increased from 22 to 31 GHz and maximum frequency of oscillation is increased from 40 to 58 GHz. Exponentially graded base doping also results ill consistently higher common-emitter current gain than uniform base doping, even though the Gummel number is twice as high and the base resistance is reduced by 40%     

Designing and prototyping data-intensive applications in the Logresand Algres programming environment

The authors present an environment and a methodology for the design and rapid prototyping of data-intensive software applications, i.e., applications which perform substantial retrieval and update activity on persistent data. In the approach, the application is formally specified using Logres, a database language which combines object-oriented data modeling and rule-based programming. These specifications are translated into Algres, an extended relational algebra, thus yielding a rapid executable prototype. Algres programs embedded into a conventional programming language interface may be converted to conventional programs operating on a commercial relational system. This methodology helps automate the conversion from declarative requirements to imperative code, performing several tasks fully automatically and reducing the probability of human errors, while integrity constraints and application specifications are expressed in a declarative language, at a very high level of abstraction