Strain hardening due to deformation twinning in α-titanium: Mechanisms

Novel experiments were conducted to elucidate the effect of deformation twinning on the mechanical response of high-purity α-titanium deformed at room temperature. Orientation-imaging microscopy (OIM), microhardness, and nanohardness evaluations were employed in conjunction with optical microscopy and quasi-static compression testing to obtain insight into the deformation mechanisms. Hardness measurements revealed that the newly formed deformation twins were harder than the matrix. This observation is perhaps the first experimental evidence for the Basinski mechanism for hardening associated with twinning, arising from the transition of glissile dislocations to a sessile configuration upon the lattice reorientation by twinning shear. This work also provided direct evidence for two competing effects of deformation twinning on the overall stress-strain response: (1) hardening via both a reduction of the effective slip length (Hall-Petch effect) and an increase in the hardness of twinned regions (Basinski mechanism) and (2) softening due to the lattice reorientation of the twinned regions.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the performance of band-limited asynchronous DS-CDMA over nakagami-m channels

In this paper we investigated the BER performance of DS-CDMA using various chip-waveforms, which include three time-limited chip-waveforms and two band-limited chip-waveforms. Closed-form formulae were derived for evaluating the achievable bit-error rate performance with the aid of the standard Gaussian approximation, when communicating over a Nakagami-m channel. The time-limited waveforms impose a low implementational complexity, since they maybe over sampled and read from a look-up table. However, they are outperformed by the frequency-domain raised-cosine waveform as well as the optimum waveform specifically designed by Cho and Lehnert for achieving the lowest possible bit error rate     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Atomistic simulations of grain boundary migration in copper

While the motion of twist boundaries can be readily studied by atomistic simulations with molecular dynamics (MD) under the action of an elastic driving force, the approach fails for tilt boundaries. This is due to the interaction of the elastic stress with the grain boundary (GB) structure, which causes plastic strain by GB sliding. A novel concept, the orientation correlated driving force, is introduced to circumvent this problem. It is shown that this concept can be successfully applied to the study of the migration of tilt boundaries. The migration behavior of several twist and tilt GBs was investigated. The transition from low-to high-angle boundaries can be captured, and a structural transition of tilt boundaries was found at high temperatures, which also affected the migration behavior. The results compare well with experimental results of the motion high-angle boundaries, but for low-angle boundaries, the agreement is poor. This article is based on a presentation made in the “Hillert Symposium on Thermodynamics & Kinetics of Migrating Interfaces in Steels and Other Complex Alloys,” December 2–3, 2004, organized by The Royal Institute of Technology in Stockholm, Sweden.     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.     

Co-digestion of ruminal content and blood from slaughterhouse industries: influence of solid concentration and ammonium generation.

At the present time, organic solid wastes from industries and agricultural activities are considered to be promising substrates for biogas production via anaerobic digestion. Moreover solids stabilisation is required before reutilization or disposal. Slaughterhouses are among the most important industries in Uruguay and produce 150,000 tons of ruminal content (RC) and 30,000 tons of blood per year. In order to determine the influence of the solids and blood contents, the ammonia inhibition and the inoculum adaptation co-digestion batch tests were performed. A set of experiences with TS concentration of 2.5%, 5% and 7.5% and different ratios of RC/blood were carried out using an inoculum from an UASB reactor. In all experiences fast blood hydrolisation was observed. A higher methane production was detected in the experiences with higher TS content. However, the fraction of solids degradation was lower in these experiences. A plateau in the biogas production was found. The free ammonia level, which was above the reported inhibitory levels, could explain this behaviour. After the inhibition period the biogas production restarted probably due to the biomass acclimatisation to the ammonia. In order to determine the inoculum adaptation a new experiment was performed. The inoculum used was the sludge coming from the first set of experiences. Based upon batch tests a 3.5 m3 pilot reactor was designed and started up. Ammonia inhibition was avoided by the start-up strategy and in two weeks the biogas production was 3.5 m3/d. The VS stabilisation with a solid retention time of 20 days was of 43%. The pilot reactor working at steady state had a TS concentration of 3-4% with a ratio of RC/blood of 10:1 at the entrance.     

软交换与3G网络互通关键技术分析

就软交换网络和WCDMAR4网络互通的关键技术进行了分析和探讨，并借此提出了对互通节点的技术要求。     

Convergence and trust in eCommerce

Trust is the key element of commerce, both for traditional models and — more recently — for eCommerce. Unlike its traditional counterpart, eCommerce relies on trust being created and maintained with the help of digital devices and services. Convergence brings significant changes to the way people interact through digital media by offering ubiquitous and seamless communication. This has a significant impact on the way trust is established and maintained, with consequent impact upon eCommerce. This paper identifies a number of the most important challenges to trust in eCommerce as well as trust-related aspects of key enablers of eCommerce. From this perspective, the paper studies an impact of convergence on trust within eCommerce to identify several positive relationships.