Crystallite growth characteristics in superfine zirconia powders and compacts

Crystallite growth characteristics of coprecipitated superfine zirconia powders have been investigated. It was found that the crystallite growth in powders follows a cubic law at 800 and 1000°C; however, the crystallite size data for compacts of both Y-TZP and YSZ cannot be fitted with a traditional parabolic or cubic law, but with a linear relation between crystallite size and the logarithm of time. In addition, it was also found that the degree of agglomeration of the powders can affect the crystallite growth.     

Prolonged release Matrix Pellets Prepared by Melt Pelletization I. Process Variables

A melt pelletization process was investigated in an 8 litre laboratory scale high shear mixer using a formulation with paracetamol, glyceryl monostearate 40-50, and microcrystalline wax. The effects of jacket temperature, product temperature during massing, product load, massing time and impeller speed were investigated by means of factorially designed experiments. The maximum yield of pellets in the range of 500-1400μm was found to approx. 90%. For process conditions preventing deposition of moist mass, the process was found to be reproducible. Impeller speed and massing time were found to be important process variables. Remarkably low in vitro drug release rates were observed in USP-dissolution tests.     

Effects of load modeling in security constrained OPF studies

Results of computational experiments carried out on an adaptation of the AEP/IEEE 30 bus test system are reported. Some selected buses were modeled using an exponential type of load model. Three cases are considered. In the first case it is assumed that the specified load at modeled buses is obtained with unity voltage. In the second case it is assumed that the transformer taps have been adjusted to give all industrial-type consumers one per unit at the low-voltage panel when the high-side voltage corresponds to the standard optimal power flow (OPF) solution. The third case differs from the second in that the specified power demand is assumed to take place when the high-side voltages correspond to the intact case of the standard security constrained OPF solution. It is concluded that a decrease in fuel cost can be obtained in some instances when load models are incorporated in security constrained OPF studies during contingencies only. In situations where a decrease in fuel cost is obtained in this manner, the magnitude of decrease depends on the total percentage of load fed by fixed tap transformers and the sensitivity of these loads to modeling     

Determination of the relationship of pressure to process time in pneumatic forming of a round membrane in the superplastic condition

The deformation of a round membrane into a cylindrical matrix is considered. The relationship of pressure to time of the process of pneumatic forming in the superplastic condition is established. The results obtained are compared with known data. A conclusion is drawn on the applicability of the proposed approach for calculation of the production parameters of forming of axisymmetric parts in the superplastic condition.Translated from Problemy Prochnosti, No. 11, pp. 71–75, November, 1993.     

Landsat-7 ETM+ on-orbit reflective-band radiometric stability and absolute calibration

Launched in April 1999, the Landsat-7 Enhanced Thematic Mapper Plus (ETM+) instrument is in its sixth year of operation. The ETM+ instrument has been the most stable of any of the Landsat instruments. To date, the best onboard calibration source for the reflective bands has been the Full Aperture Solar Calibrator, a solar-diffuser-based system, which has indicated changes of between 1% to 2% per year in the ETM+ gain for bands 1-4 and 8 and less than 0.5%/year for bands 5 and 7. However, most of this change is believed to be caused by changes in the solar diffuser panel, as opposed to a change in the instrument's gain. This belief is based partially on vicarious calibrations and observations of "invariant sites", hyperarid sites of the Sahara and Arabia. Weighted average slopes determined from these datasets suggest changes of 0.0% to 0.4% per year for bands 1-4 and 8 and 0.4% to 0.5% per year for bands 5 and 7. Absolute calibration of the reflective bands of the ETM+ is consistent with vicarious observations and other sensors generally at the 5% level, though there appear to be some systematic differences.     

Three-dimensional inverse scattering of a dielectric target embedded in a lossy half-space

A modified iterative Born method is applied for three-dimensional inversion of a lossless dielectric target embedded in a lossy half-space. The forward solver employs a modified form of the extended Born method, and the half-space Green's function is computed efficiently via the complex-image technique. Example results are shown, with all scattering data based on a computational model, utilizing a rigorous forward solver distinct from that employed in the inversion. In addition, distinct gridding schemes are used in the forward and inverse solvers. Simple Tikhonov regularization is found to yield adequate results for inversion of noisy data.     

A reliable and manufacturable method to induce a stress of >1 GPa on a P-channel MOSFET in high volume manufacturing

This letter discusses a reliable and manufacturable integration technique to induce greater than 1 GPa of stress into a p-channel MOSFET, which will be required to increase the drive current beyond 1 mA//spl mu/m at the sub-90-nm process generation. Uniaxial compressive stress is introduced into the p-channel by both a selective deposition of SiGe in the source/drain and an engineered 2.5-GPa compressively stressed nitride. The highest to date compressively stressed SiN film is obtained by heavy ion bombardment during the deposition of the film.     

Total and acid-soluble fluoride content of infant cereals, beverages and biscuits from Brazil

Total fluoride (TF) and HCl 0.01 M ('gastric juice')-soluble fluoride (SF) were analysed in infant foods, beverages and calcium-rich biscuits. Samples were divided into seven categories: children cereals (A), chocolate-flavoured milk (B), soy beverages (C), filled biscuits (D), non-filled biscuits (E), wafer biscuits (F) and corn starch biscuits (G). Mean TF concentrations ± SD (amplitude, unit µg F ml^-1 or µg F g^-1) were: (A) 4.25 ± 3.04 (0.20 - 7.84, n = 6); (B) 0.34 ± 0.47 (0.05-1.27, n = 6); (C) 0.15 ± 0.07 (0.09-0.29, n = 8); (D) 8.44 ± 1.76 (7.65-10.47, n = 4); (E) 12.41 ± 1.15 (10.69-13.68, n = 4); (F) 0.35 ± 0 (0.34-0.36, n = 4) and (G) 7.77 ± 1.12 (6.86-8.68, n = 2). Five samples of cereals, one sample of chocolate-flavoured milk and 10 samples of biscuits were analysed for SF. In cereals analysed for SF, all fluoride was soluble, while for the chocolate-flavoured milk, approximately 50% of TF was soluble. Regarding the biscuits analysed for SF approximately 20% of TF was soluble. It was observed that some of the cereals and beverages, and most of the biscuits analysed, might be important contributors to total daily fluoride intake. When consumed just once per day, cereals and beverages might supply up to 25% of the maximum recommended daily fluoride intake (0.07 mg F kg^-1 body weight) for a 2-year-old child (12 kg). For the filled, non-filled and corn starch biscuits, when 3, 32 or 20 units of them, respectively, are consumed just once per day, they may supply up to 16% of the maximum recommended daily fluoride intake. However, only approximately 25% of fluoride absorption occurs from the stomach and 75% from the small intestine. Therefore, a higher fluoride bioavailability is possible.