轻钢结构屋面的应用

针对轻钢结构构屋面系统的性能、特点、构造和施工方法进行了论述，介绍了与传统建筑形成对照的一种新型结构形式，使传统的重盖、肥梁、胖柱、色彩单一的建筑状况得到改善。轻钢结构的优点将使它的生产规模、适用范围不断扩大，从而以其漂亮的外和合理的造价美化人类的生活环境。     

Simulation and design methodology for a 50-Gb/s multiplexer/demultiplexer package

A 50 Gb/s package for SiGe BiCMOS 4:1 multiplexer and 1:4 demultiplexer targeting SONET OC-768 serial communication systems is introduced in this work. The package was designed to facilitate bit-error-rate tests and constructed with high-speed coaxial connectors, transmission lines on ceramic substrate, ribbon bonds for chip-to-package interconnects, and a metal composite housing. Numerical simulations were conducted to guide the package design, and both small signal measurements and operational tests were performed thereafter to verify the design and modeling concepts. To keep the model structure under the existing computing capability, the simulation was segmented into three sections - coaxial connector to transmission line, transmission line alone, and transmission line to ribbon bond, and then the results were assembled to predict the performance of the entire package. The package was operated up to 50 Gb/s with low degradation to input digital waveforms and free of error.     

拉伸速率对PP/GB复合材料力学性能的影响

应用Instron材料试验机考察了室温下拉伸速率对玻璃微珠填充聚丙烯复合材料的弹性模量和屈服强度的影响，结果表明，随着微珠含量的增加，试样的弹性模量（Ec）增大，且与拉伸应变速率呈近乎幂律函数关系，而屈服强度（бyc）则随着微珠体积分数（Φf）的增加呈线性函数形式下降，并随着拉伸应变速率的增加呈幂律函数形式提高，此外，讨论了Ec、Φf与бyc三者之间的关系。     

现场总线技术在发电系统数据采集中的应用

介绍了现场总线网络在干熄焦汽轮机发电生产过程中所起的作用，并重点介绍了系统所完成的数据采集，监视和管理等功能。     

横流均匀环境中三维线源型正负浮力射流特性研究

本文利用混合有限分析法及交错网格。对横流均匀环境中三维线源型正负浮力射流及负浮力射流的特性进行研究，分析了不同工况下流速，温度和湍动能在断面上的分布及影响射流轨迹线的因素，讨论了轨迹线上温度的变化及浮力射流的贴壁现象。对三维长线源型负浮力射流，分析了流速比，喷口弗汝德数对负浮力射流的影响。     

CO_2激光对兔脑组织血脑屏障的影响

同等功率和照射时间条件下,在14只家兔大脑皮质运用伊文思蓝染料和超微结构观察方法进行血脑屏障改变的研究。结果表明:CO_2激光作用十分表浅,且激光作用后的水肿层血脑屏障改变是可逆的。     

Ca原子的Penning离化

用614.3nm染料激光照射以Ne为缓冲气体的Ca空心阴极灯,观察到了Ca原子的Pen-ning离化效应。对比在Li空心阴极灯中获得的光电流信号,解释了Ca原子的彭宁离化。     

自适应相位制中波同步广播及现场试验

在本试验中，采用智能同步广播激励器和ＣＣＴＶ传输的１ＭＨｚ标频，实现了中波同步广播同频保护率趋于０ｄＢ．并提出了自适应相位跟踪同步的概念。     

Enhancement of oxide break-up by implantation of fluorine inpoly-Si emitter contacted p+-n shallow junctionformation

In this study, it is demonstrated that the incorporation of fluorine can enhance poly-Si/Si interfacial oxide break-up in the poly-Si emitter contacted p⁺-n shallow junction formation. The annealing temperature for breaking up the poly-Si/Si interfacial oxide has been found to be as low as 900°C. As a result, the junction depth of the BF₂-implanted device is much larger than that of the boron-implanted device     

Performance analysis of adaptive interleaving for OFDM systems

We proposed a novel interleaving technique for orthogonal frequency division multiplexing (OFDM), namely adaptive interleaving, which can break the bursty channel errors more effectively than traditional block interleaving. The technique rearranges the symbols according to instantaneous channel state information of the OFDM subcarriers so as to reduce or minimize the bit error rate (BER) of each OFDM frame. It is well suited to OFDM systems because the channel state information (CSI) values of the whole frame could be estimated at once when transmitted symbols are framed in the frequency dimension. Extensive simulations show that the proposed scheme can greatly improve the performance of the coded modulation systems utilizing block interleaving. Furthermore, we show that the adaptive interleaving out performs any other static interleaving schemes, even in the fast fading channel (with independent fading between symbols). We derived a semi-analytical bound for the BER of the adaptive interleaving scheme under correlated Rayleigh fading channels. Furthermore, we discussed the transmitter-receiver (interleaving pattern) synchronization problem