Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。     

碳基采暖电热材料研究进展

近几年,由于节能与环保的需求,电取暖的方式得到大力的推广,电热材料的研究与应用受到人们广泛的重视。非金属碳基电热材料是新型的节能型电热采暖材料,本文重点对影响非金属碳基电热材料中的炭黑基电热材料、碳纤维基电热材料、碳晶电热材料电热性能的因素及相关应用进行了综述。     

2A12铝合金化学铣切加工工艺探讨

为了精确加工2Al2铝合金,探讨了化铣时间和温度对其化铣速率及表面粗糙度的影响,采用现代技术对化铣工件的力学性能进行了测试与分析.结果表明:延长非化铣部位保护胶固化时间并使保护部位向非加工面位移3～5 mm可很好地解决未化铣区域的腐蚀问题;随化铣时间的延长,化铣速率降低,且化铣温度与化铣速率呈现正相关性;化铣表面的粗糙度随化铣时间的延长而增加,随化铣温度的升高呈先减小后增加的趋势;化铣后材料的抗拉强度和屈服强度均有所提高.     

5-二茂铁基噁唑的合成研究

以二茂铁甲醛和对甲苯磺酰基异氰(TOSMIC)为原料,经过Van Leusen反应,一步合成目标化合物5-二茂铁基噁唑,通过~1HNMR、~(13)CNMR和ESI-MS对其结构进行表征,并对影响收率的主要因素进行考察。结果表明,在物料比n(TOSMIC)∶n(二茂铁甲醛)为1.1∶1、反应溶剂为甲醇、K_2CO_3用量即n(K_2CO_3)∶n(二茂铁甲醛)为2.0∶1、反应温度为65℃、反应时间为8 h的最佳条件下,目标化合物收率达到74.7%。该方法具有原料廉价易得、反应操作简单、收率高等优点,具有一定的应用价值。     

基于Q-learning的不确定环境BDI Agent最优策略规划研究

BDI模型能够很好地解决在特定环境下的Agent的推理和决策问题,但在动态和不确定环境下缺少决策和学习的能力。强化学习解决了Agent在未知环境下的决策问题,却缺少BDI模型中的规则描述和逻辑推理。针对BDI在未知和动态环境下的策略规划问题,提出基于强化学习Q-learning算法来实现BDI Agent学习和规划的方法,并针对BDI的实现模型ASL的决策机制做出了改进,最后在ASL的仿真平台Jason上建立了迷宫的仿真,仿真实验表明,在加入Q-learning学习机制后的新的ASL系统中,Agent在不确定环境下依然可以完成任务。