Design and fabrication of 3D‐plotted polymeric scaffolds in functional tissue engineering

Regenerating the load‐bearing tissues requires 3D scaffolds that balance the temporary mechanical function with the biological requirements. In functional tissue engineering, designing scaffolds with biomimetic mechanical properties could promote tissue ingrowth since the cells are sensitive to their local mechanical environment. This work aims to design scaffolds that mimic the mechanical response of the biological tissues under physiological loading conditions. Poly(L ‐lactide) (PLLA) scaffolds with varying porosities and pore sizes were made by the 3D‐plotting technique. The scaffolds were tested under unconfined ramp compression to compare their stress profile under load with that of bovine cartilage. A comparison between the material parameters estimated for the scaffolds and for the bovine cartilage based on the biphasic theory enabled the definition of an optimum window for the porosity and pore size of these constructs. Moreover, the finite element prediction for the stress distribution inside the scaffolds, surrounded by the host cartilaginous tissue, demonstrated a negligible perturbation of the stress field at the site of implantation. The finite element modeling tools in combination with the developed methodology for optimal porosity/pore size determination can be used to improve the design of biomimetic scaffolds. POLYM. ENG. SCI., 47:608–618, 2007. © 2007 Society of Plastics Engineers.     

国产子午线轮胎专用天然橡胶应用试验

通过对国产子午线轮胎专用天然橡胶的化学分析、物理性能检验和进行胎面胶、胎体胶的小配合、大配合胶料试验，并与进口天然橡胶试验结果进行对比，研制了一批用国产子午线轮胎专用天然橡胶生产的９．００Ｒ２０全钢子午线轮胎作里程试验。试验结果表明，国产专用天然橡胶只要适当降低塑性初值（Ｐ＿０）和生胶门尼粘度，按国际通用标准进行包装，完全可以代替马来西亚标准橡胶（ＳＭＲ１０和ＳＭＲ２０）用于子午线轮胎生产中。     

硅氮聚合物交联的室温硫化橡胶的研究Ⅰ．热稳定性的研究

本文利用硅氮聚合物作文联剂使双组分缩合型室温硫化硅橡胶在不需要催化剂存在下就能交联硫化，通过时硫化胶老化后的热失重、交联密度和力学性能的测定，表明这种硫化胶的耐温性能由２００℃提高到３５０℃。对硫化胶的降解动力学研究表明：降解反应活化能由７０ｋＪ／ｍｏｌ提高到３３０ｋＪ／ｍｏｌ，这是由于消除了端基引发的主链降解。     

新型无机絮凝剂聚硅酸铝的制备及其模拟净水试验

以硫酸铝为主要原料，引入硅酸根，在高速剪切的条件下，经过聚合，熟化反应合成出有效铝含量(以Al2O3计)9．5％～12％，碱化度45％～55％，pH2．8～3．8的半透明液体PASS，该产品稳定性好，处理后水中的铝残余远小于PAC。对产品用硅藻土配的浊度水进行絮凝试验，并与PAC、硫酸铝对比，去浊效果是PAC的一倍。且不受pH因素影响。     

Continuous ethanol production from wood hydrolysate by chemostat and total cell retention culture

Chemostat and total cell retention cultures with internal filter system ofSaecharomyc.es cerevisiae H1-7 were carried out to produce ethanol from wood hydrolysate. Maximum ethanol productivity obtained in a chemostat with the aeration rate of 1 vvm was 3.79 g/(L·h). This was 20% higher than that in a chemostat without aeration. However, the substrate was not completely consumed at the dilution rate with the maximum productivity. The realistic productivity, which has higher than 99% conversion rate of substrate, was. 2.95 g/(L·h). The maximum productivity in the total cell retention culture was 6.65 g/(L·h) at the dilution rate of 0.19 h¹ and the residual glucose concentration was negligible.     

褐煤成型的研究

由于褐煤具有含水率高，灰份大，易风化，发热值低等特点，使得成型难度很大．本文重点研究水份粒度、添加剂、成型压力等对褐煤成型的影响．最佳条件：粒度＜１ｍｍ，水份１４～１６％，压力＞５０Ｔｆ，添加剂１０～２０％．     

High clay content nanocomposite hydrogels with surprising mechanical strength and interesting deswelling kinetics

A series of high hectorite content nanocomposite Poly (N-isopropylacrylamide), (PNIPAAm), hydrogels have been successfully synthesized by choosing a special kind of hectorite (Laponite XLS) modified by tetrasodium pyrophosphate. It was found that these hydrogels show surprising mechanical properties (i.e. tensile strength: 1 MPa, elongation at break: 1400%) and complicated deswelling behavior, which are due to the high clay content of the hydrogels and ionic dispersant contained in Laponite XLS, respectively.     

Hydrodynamics of gas-solid flow around immersed tubes in bubbling fluidized beds

A numerical study was conducted based on the gas-solid two-fluid model using the body-fitted coordinate system to analyze the behavior of particles and bubbles flow in bubbling fluidized beds without and with immersed tubes. The kinetic theory of granular flow was implemented in the model. The images of simulated instantaneous particle concentration and velocity gave the process of the formation, coalescence and eruption of bubbles. The effects of the tube pitch and superficial gas velocity on the fluidization in a bubbling fluidized bed were investigated. Calculated bubble frequencies without and with immersed tubes were in agreement with previous experimental and simulation findings. The wavelet multi-resolution analysis was used to analyze the simulated data of instantaneous particle concentration. From the random-like particle concentration fluctuations, the fluctuating components due to particle flow and bubble motion can be extracted based on the wavelet multi-resolution analysis over a time-frequency plane.     

填充床鼓泡电化学反应器行为特性研究──Ⅰ.丙烯阳极直接氧化的数学模拟

本文建立了填充床鼓泡电化学反应器的一维数模．该模型既考虑了反应动力学，也考虑了体系的基本传递特性．模拟结果可以描述床层的径向电势、电流和浓度分布．     

An NMR study of the dissociation of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate) and its crosslinking of polymers containing labile hydrogens. II

Nuclear magnetic resonance spectroscopy has been used to study the dissociation and reaction of N,N′-(2-propyloximino)-4,4′-methylenebis(phenylcarbamate), as a crosslinking agent for polymers containing labile hydrogens. The crosslinking of poly(acrylic acid), polyacrylamide, and poly(vinyl alcohol) was found to result upon heating each to 150°C for 10 min with this component at 2–10 wt %.