镁钴铝类水滑石催化合成安息香甲醚

采用共沉淀法制备了镁钴铝类水滑石化合物(MgCoAl-HTLcs),并用 X 射线衍射、扫描电子显微镜、NH_3程序升温脱附等方法对 MgCoAl-HTLcs 进行了表征,并以 MgCoAl-HTLcs 为催化剂催化苯甲醛与甲醇反应合成安息香甲醚,研究了n(Mg):n(Co):n(Al)、催化剂用量、原料配比、反应温度、反应时间对合成反应的影响。表征结果显示,MgCoAl-HTLcs 的晶相完整,表面主要为弱酸、弱碱性。催化合成安息香甲醚的适宜条件为:MgCoAl-HTLcs 催化剂用量0.10 g(约为原料总质量的0.23%),n(Mg):n(Co):n(Al)=0.4:1.6:1.0,V(苯甲醛):V(甲醇)=3:50,反应温度50℃,反应时间150 min。在此条件下,苯甲醛的平衡转化率达77.49%,安息香甲醚选择性接近100%。为洁净合成安息香甲醚开辟了一条新的途径。     

Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

实施六大工程打造民生水利

我省针对十年九旱、水资源短缺、生态与环境脆弱的特点，确定了今冬明春农田水利基本建设的目标任务，明确以实施兴水战略为主线，以改善民生为目标，以创新机制为保障，全面掀起冬春农田水利基本建设新高潮。     

三相异步电动机运行指标的分析

利用电机学理论分析了影响电机起动转矩、起动电流、最大转矩和最小转矩的因素。     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。     

Integrated magnetic full wave converter with flexible output inductor

A new integrated magnetic full wave DC/DC power converter that provides flexible transformer design by incorporating an independent output inductor winding is introduced. The transformer is implemented on a traditional three-leg magnetic core. The inductor winding can be separately designed to control the output current ripple. The cross-sectional area of the inductor core leg can be reduced dramatically. The operation and performance of the proposed circuit are verified on a 100 W prototype converter.     

Ф16mm、Ф18mm钼棒的研制

采用等静压制法，压制钼圆棒坯，经中频高温烧结，制得尺寸适合、用户满意的钼电极棒。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities